In this study, a novel shape memory polymer (SMP), eggshell membrane (ESM), with macroscopic mesh structures and microscopic crosslinked protein fibers, has shown water-stimulated shape recovery characteristics. Our results show that the collagen triple-helical molecular chains and disulfide-rich motifs in the ESM function as net-points retaining essential structures during deformation, while hydrogen bonds play a key role as switch units for shape recovery through water stimulation. We also demonstrate that programmable shape recovery characteristics of ESM can be obtained by modulating the number of net-points. This study may inspire the design of new programmable SMPs.

Forty-eight different Ag–Al–Zr ternary alloys were prepared in various compositions to determine the metallic glass region in the Ag–Al–Zr ternary system. Experimental results indicated that the metallic glass region in the Ag–Al–Zr ternary system is Ag20–30Al10–30Zr50–60. The Ag20Al30Zr50 and Ag30Al20Zr50 alloys are supposed to have the best glass-forming ability in the Ag–Al–Zr ternary system. The phase equilibria of the Ag–Al–Zr ternary system at 773 K (500 °C) were investigated and compared with the metallic glass region results in the Ag–Al–Zr ternary system. Ternary isothermal sections of the Ag–Al–Zr system at 773 K (500 °C) were established and two ternary intermetallic phases were observed in this isothermal section.

The authors carried out matched experiments and molecular dynamics simulations of the compression of nanopillars prepared from Cu|Au nanolaminates with up to 25 nm layer thickness. The stress–strain behaviors obtained from both techniques are in excellent agreement. Variation in the layer thickness reveals an increase in the strength with a decreasing layer thickness. Pillars fail through the formation of shear bands whose nucleation they trace back to the existence of surface flaws. This combined approach demonstrates the crucial role of contact geometry in controlling the deformation mode and suggests that modulus-matched nanolaminates should be able to suppress strain localization while maintaining controllable strength.

We have prepared stable ultrafine narrow dispersed copper nanoparticles (Cu-NPs) using a facile chemical reduction technique below room temperature (300 K), without any template. X-ray diffraction and high-resolution transmission electron microscopy studies reveal the growth of highly crystalline Cu-NPs with an average diameter of 2.2 nm. Interestingly, these Cu-NPs demonstrate both interband electronic transitions along with usual surface plasmon resonance, a unique phenomenon previously unobserved in any noble metal nanoparticles. These Cu-NPs do not get oxidized easily and could be suitable candidates for different optical devices, heat transfer liquids, and biological applications.

Effective modification of existing supported catalyst has attracted plenty of interests recently. Herein, we introduced ultrasonication to synthesize the palladium-loaded cobalt-based zeolitic imidazolate framework and compared its properties with those using the conventional method. Remarkably, the ultrasonicated frameworks possess 15.33% higher of Brunauer–Emmett–Teller (BET) surface area and 63.37% higher of t-plot external surface area, respectively, which lead up to 23% rise in the degradation of organic pollutants under optimized conditions. Characterizations clearly revealed the causality between ultrasonication, morphology, and catalytic performance compared with their non-ultrasonicated counterparts which further demonstrates a simple but useful method for the modification of supported catalysts.

Nanomaterials have been proposed as key components in biosensing, imaging, and drug delivery since they offer distinctive advantages over conventional approaches. The unique chemical and physical properties of graphene make it possible to functionalize and develop protein transducers, therapeutic delivery vehicles, and microbial diagnostics. In this study, we evaluate reduced graphene oxide as a potential nanomaterial for quantification of microRNAs including their structural differentiation in vitro in solution and inside intact cells. Our results provide evidence for the potential use of graphene nanomaterials as a platform for developing devices that can be used for microRNA quantitation as biomarkers for clinical applications.

A model with which to predict the effect of coplanar electrode geometry on diffraction uniformity in photorefractive polymer display devices was developed. Assumptions made in the standard use cases are no longer valid in the regions of extreme electric fields present in this type of device. Using electric-field induced second-harmonic generation through multiphoton microscopy, the physical response in regions of internal electric fields which fall outside the standard regimes of validity were probed. Adjustments to the standard model were made and the results of the new model corroborated through holographic four-wave mixing measurements.

The remarkable broadband and omnidirectional anti-reflectivity observed in the glasswing butterfly arises from the random array of nanopillars present on their wings. In the present study, analogous structures have been replicated on transparent substrates using a scalable, low-cost method that exploits surface dewetting of silver thin films on silica substrates to form an etch mask. Directional etching was applied with high selectivity between Ag and SiO2 using CHF3, allowing large aspect ratios to be achieved with 20 min etches. Single-sided nanostructuring of glass by this method improved the transmission of light by 2–8% for viewing angles of 25°, 45°, and 65°.

The understanding of adhesion and survival behavior of bacterial pathogens on implant surfaces are critical to control and reduce implant-associated infections. Herein, the authors investigate the interactions of Staphylococcus aureus, one of the most prevalent causes of implant infections, with Mg–4Zn–0.5Ca implants. It was found that within 60 min of exposure, 99.1% of adherent bacteria were inactivated. The combination of unique mechanical properties, biodegradation kinetics, and antimicrobial characteristics of Mg–4Zn–0.5Ca alloy makes it a promising candidate for future implant applications.

Solid oxide fuel cells (SOFCs) efficiently generate electricity, but high operating temperatures (T op > 800 °C) limit their utility. Reducing T op requires mixed ion–electron conducting (MIEC) cathode materials. Density functional theory is used here to investigate the role of potassium substitutions in the MIEC material Sr1−x K x FeO3 (SKFO). We predict that such substitutions are endothermic. SrFeO3 and SKFO have nearly identical metallic electronic structures. Oxygen vacancy formation energies decrease by ~0.2 eV when x K increases from 0 to 0.0625. SKFO is a promising SOFC MIEC cathode material; however, further experimental investigations must assess its long-term stability at the desired operating temperatures.

A broadband magnetoelectric energy harvester, consisting of Fe1−xGax (Galfenol) as the magnetostrictor and a relaxor ferroelectric single crystal as the piezoelectric, has been designed and optimized. Finite element analysis (FEA) has been employed to show that either a linear displacement or a 180° rotation of a magnet is sufficient to achieve maximum stroke from the Galfenol rod, which induces a rhombohedral to orthorhombic phase transition in Pb(In1/2Nb1/2)O3–Pb(Mg1/3Nb2/3)O3–PbTiO3 that produces a large jump in voltage. A rotational design based on a pendulum with an unbalanced mass was fabricated and used to confirm the validity of our FEA model.

In this paper new materials and substrate approaches are discussed which have potential to provide (Al)GaN buffers with a better crystal quality, higher critical electrical field, or thickness and have the potential to offer co-integration of GaN switches at different reference potentials, while maintaining lower wafer bow and maintaining complementary metal–oxide semiconductor (CMOS) compatibility. Engineered silicon substrates, silicon on insulator (SOI) and coefficient of thermal expansion (CTE)-matched substrates have been investigated and benchmarked with respect to each other. SOI and CTE-matched offer benefits for scaling to higher voltage, while a trench isolation process combined with an oxide interlayer substrate allows co-integration of GaN components in a GaN-integrated circuit (IC).

We propose a device to secure random data in analog format, so that it is taken off the digital grid. Such action will turn off the means by which remote hackers violate security. A physical “rock” manufactured through 3D printing technology, constructed on the basis of high-grade randomness, which is packed into the comprising materials of that rock. The rock functions as an oracle, and does not allow any massive copy of its content. Thus, a major claim of this Prospective is that materials science and engineering may hold the keys to the future of cryptography.

Self-assembly of multiferroic oxide composites by chemical and biochemical methodology is discussed. The approach involves covalently attaching organic functional groups or oligomeric DNA/RNA to the nanoparticles (NPs). The organic functional groups are only reactive toward functional groups located on different NPs. Using oligomeric DNA/RNA, one could program NPs to only interact with particles possessing complementary DNA/RNA. We have applied both concepts to the assembly of nanostructures with ferrites for the ferromagnetic phase and barium titanate for the ferroelectric phase. The assembled core–shell particles and superstructures obtained in a magnetic field show evidence for strong interactions between the magnetic and ferroelectric subsystems.

A correction method for linear hardening materials is brought forward to obtain the true (or nearly true) modulus of cylindrical specimens with middle aspect ratios in compression tests. By considering the stress concentration near the interface between the specimen and the compression platen caused by slanted contact, a “sandwich” model is developed. A correction formula is derived and all parameters can be obtained from the tested stress–strain curve. Experiments were performed on Al 2024 specimens with four aspect ratios. The corrected results are closer to the intrinsic modulus than the tested values, which verify the effectiveness of the correction method.

Cation doping is a practical way of engineering the optical properties of one-dimensional semiconductor nanomaterials, such as their band gap. We have grown zinc oxide (ZnO) nanorods doped with sodium cations (Na+) using a hydrothermal method at temperatures as low as 60 °C. We have investigated the effect of different concentrations of Na+ on structural and optical properties and morphology of the ZnO nanostructures. We have also simulated and discussed the chemical route of formation of doped and undoped ZnO nanorods. We found that, for low-temperature hydrothermal doping of ZnO nanorods with Na+, the optimum concentration ratio of zinc to sodium precursors is 1:10.

A review of the literature offers an explanation for the large anomalous electro-optic (e.o.) effect reported by Fujiwara et al. in 1994. It is based on the large e.o. coefficient of ordered water at an interface measured in recent years >1000 pm/V. More broadly, the concept of water-based photonics, where water could be a new platform material for devices and systems, is introduced, suggesting that liquid states of matter can allow ready shaping and exploitation of many processes in ways not previously considered. This paper is a commentary on the significance of this new understanding and the broader interest of water in photonics, particularly its consideration as a new platform material.

Machinable mica glass ceramics were synthesized by sintering method. The crystal phase was characterized using x-ray diffraction, showing that the main crystal phase was fluorophlogopite. Mechanical properties were measured at different temperatures. The results demonstrated that bending strength and fracture toughness increased 28% and 24% when temperature decreased from 300 to 77 K, respectively. Compressive strength also increased at cryogenic temperatures, but a higher value was obtained at 195 K. According to scanning electron microscope observation, the extraction of mica platelets was observed at 77 K, which may be the toughening mechanism of machinable mica glass ceramics.

The time-dependent pyramidal or conical indentation of viscoelastic–plastic materials, such as glassy polymers, is examined by a flexible, Kelvin-like model. The model equation is simply solved numerically for a wide range of material properties and indentation loading sequences. The flexibility of the model is demonstrated by generating typical indentation responses for a metal, a ceramic, an elastomer, and a glassy polymer. Polymer indentation is further examined under ramp, hold, and cyclic loading conditions, including adhesive effects. The model and approach should be particularly useful in identifying the various deformation components contributing to observed instrumented indentation phenomena.

This paper proposes to improve the corrosion resistance of stainless steel using the photocathodic protection (PCP) method with CdS/PbS/titanium dioxide (TiO2) as the photoanode material. Cadmium sulfide (CdS)/lead sulfide (PbS) quantum dot (QD) heterostructure layered on TiO2 enhanced the photoelectrochemical performance and improved the PCP of 304 stainless steel. The photoanode film can protect 304 stainless steel for a period of upto 3 months against corrosion. This work demonstrates that CdS/PbS/TiO2 tandem heterostructure is a promising durable and stable photoanode, which can protect stainless steel in both dark and illuminated conditions.