Five Au complexes are evaluated for the reduction reaction of CO2 via cyclic voltammetry and in a photocatalytic system. Electrochemically, the complexes were all evaluated for pre-association with CO2 prior to electrochemical reduction and for thermodynamic favorability for CO2 reduction in photocatalytic systems. The complexes were evaluated in photocatalytic reactions using an Ir-based photosensitizer and a sacrificial electron donor for the conversion of CO2 to CO. Au-complex counterion effects on the photocatalytic reaction were analyzed by varying weakly coordinating counterions with significant performance changes noted. At low Au-complex concentrations, a high TON value of 700 was observed.

The flow of particles through confined volumes has appeared under different contexts in nature and technology. Some examples include the flow of red blood cells or drug delivery vehicles through capillaries, or surfactant-based particles in nano- or microfluidic cells. The molecular composition of the particles along with external conditions and the characteristics of the confined volume impact the response of the particle to flow. This review focuses on the problem of phospholipid vesicles constrained to flowing in channels. The review examines how experimental and computational approaches have been harnessed to study the response of these particles to the flow.

Indentation and scratch models are proposed to numerically investigate effects of compressive prestress on film's mechanical responses. In indentation, normal stress distributions are strongly dependent on film thickness; the applied force and the maximum normal stresses with a prestress are much larger than without prestress. For various film thicknesses the change in the normal force in scratch between the non-prestressed and prestressed films is 4%–23%. The scratch friction coefficient is larger with prestress than without prestress. With biaxial or uniaxial prestress the material becomes more difficult to deform or to slide at the contact surface compared with cases without prestress.

Human organoid models recapitulate many aspects of the complex composition and function of native organs. One of the main challenges in developing these models is the growth and maintenance of three-dimensional tissue structures and proper cellular organization that enable function. Biomaterials play an important role by providing a defined and tunable three-dimensional environment that is required for complex cellular organization and organoid growth in vitro or in vivo. This review summarizes organoids of the respiratory and digestive system, and the use of biomaterials to improve upon these model systems.

Nickel thin films were prepared by electroless plating in a foam of electrolyte that was generated by bubbling nitrogen gas into a hypophosphite-based electroless plating solution to which was added a surfactant of sulfuric acid monododecyl ester sodium salt. Although the film growth rate in the foam was considerably lower than that in the conventional liquid, film growth was enhanced by inducing a flow in the foam. Compared with films deposited in liquid, the films deposited in foam had a smaller number of pinholes, smaller crystallite size, and superior corrosion resistance. The ferroxyl indicator test showed that the area of corrosion can be reduced to less than 1/20 by depositing the film in foam instead of liquid.

Millions of micro electro mechanical system sensors are fabricated each year using an ultra-clean process that allows for a vacuum-encapsulated cavity. These devices have a multi-layer structure that contains hidden layers with highly doped silicon, which makes common imaging techniques ineffective. Thus, examining device features post-fabrication, and testing, is a significant challenge. Here, we use a combination of micro- and nano-scale x-ray computed tomography to study device features and assess failure mechanisms in such devices without destroying the ultra-clean cavity. This provides a unique opportunity to examine surfaces and trace failure mechanisms to specific steps in the fabrication process.

Physical understanding of crack propagation is a fundamental issue in the industry. In the literature, crack velocities of polymer materials are strongly dependent on their visco-elastic properties and energy release rates. Recently, numerical and theoretical studies have proposed that structural sizes in polymers also influence on crack propagation. Here, using polymer sheets with similar visco-elastic properties but with different pore sizes, we vary explicitly the representative structural size and examine the effect of the size on crack propagation. Findings in this work help us to understand crack propagation in polymer materials and bio-inspired materials which have porous structures.

This work investigated the photophysical pathways for light absorption, charge generation, and charge separation in donor–acceptor nanoparticle blends of poly(3-hexylthiophene) and indene-C60-bisadduct. Optical modeling combined with steady-state and time-resolved optoelectronic characterization revealed that the nanoparticle blends experience a photocurrent limited to 60% of a bulk solution mixture. This discrepancy resulted from imperfect free charge generation inside the nanoparticles. High-resolution transmission electron microscopy and chemically resolved X-ray mapping showed that enhanced miscibility of materials did improve the donor–acceptor blending at the center of the nanoparticles; however, a residual shell of almost pure donor still restricted energy generation from these nanoparticles.

Quantum dots (QDs) are increasingly employed in biologic imaging applications; however, anecdotal reports suggest difficulties in QD bioconjugation. Further, the stability of commercial QDs during bioconjugation has not been systematically evaluated. Thus, we examined fluorescence losses resulting from aggregation and declining photoluminescence quantum yield (QY) for commercial CdSe/ZnS QD products from four different vendors. QDs were most stable in the aqueous media in which they were supplied. The largest QY declines were observed during centrifugal filtration, whereas the largest declines in colloidal stability occurred in 2-(N-morpholino)ethanesulfonic acid (MES) buffer. These results enable optimization of bioconjugation protocols.

The authors demonstrate that multicomponent metallic alloy nanofoams can be synthesized by the polymeric templating method. The present approach enabled alloy compositions not accessible via commonly used dealloying or co-deposition methods. The authors report the synthesis of a Cu50Ni50 alloy nanofoam using electrospinning polymeric templating, which exhibits distinct polycrystallinity, process-driven segregation, and enhanced mechanical strength over pure Cu nanofoams. Transmission electron microscopy revealed microscopic grain formation and their variable compositions. The processing method is applicable to the synthesis of a wide range of multicomponent metal porous materials, creating new research opportunities for noble alloy foams not available through wet electrochemical routes.

Zirconium thin films were irradiated at room temperature with an 800 keV Zr+ beam using a 6 MV HVE Tandem accelerator to 1.36 displacement per atom damage. Freestanding tensile specimens, 100 nm thick and 10 nm grain size, were tested in situ inside a transmission electron microscope. Significant grain growth (>300%), texture evolution, and displacement damage defects were observed. Stress–strain profiles were mostly linear elastic below 20 nm grain size, but above this limit, the samples demonstrated yielding and strain hardening. Experimental results support the hypothesis that grain boundaries in nanocrystalline metals act as very effective defect sinks.

Two thiophene-based semiconductors, a vapor-deposited small molecule and an amorphous polymer, as well as pentacene for comparison, show potential in enhancing the thermoelectric properties of tellurium (Te) nanowires. For vapor-deposited films, Te nanostructures form directly on glass substrates or organic semiconductor films. The resulting Te power factor (S2σ) was enhanced from 36 to 45 W/mK2 (56 for pentacene) because the bilayer provides an enhancement in Seebeck (S) without compromising conductivity (σ). For solution deposited polymer blends, we obtained power factors from a Te nanowire network that alone would not have sufficient connectivity (up to 0.1 µW/mK2). While the organics are unoptimized, they are prototypical materials for further development.

Solid state batteries are an emerging alternative to traditional liquid electrolyte cells that provide potential for safe and high-energy density power sources. This report describes a self-forming, solid state battery based on the Li/I2 couple using an LiI-rich LiI(3-hydroxypropionitrile)2 electrolyte (LiI–LiI(HPN)2). As the negative and positive active materials are generated in situ, the solid electrolyte–current collector interfaces play a critical role in determining the electrochemical response of the battery. Herein, we report the investigation of solid electrolyte–current collector interfaces with a self-forming LiI–LiI(HPN)2 solid electrolyte and the role of varying interface design in reducing resistance during cycling.

Mesenchymal stem cell behavior can be regulated through mechanical signaling, either by dynamic loading or through biomaterial properties. We developed intrinsically responsive tissue engineering scaffolds that can dynamically load cells. Porous collagen- and alginate-based scaffolds were functionalized with iron oxide to produce magnetically active scaffolds. Reversible deformations in response to magnetic stimulation of up to 50% were recorded by tuning the material properties. Cells could attach to these scaffolds and magnetically induced compressive deformation did not adversely affect viability or cause cell release. This platform should have broad application in the mechanical stimulation of cells for tissue engineering applications.

Chemical vapor deposition is the most proficient method for growing graphene on copper foils due to its scalability, repeatability, and uniformity, etc. Herein, we systematically study the effect of oxygen (O2) exposure on graphene growth. We introduced O2 before and during the growth, and then studied its effects on the morphology, crystallinity, and nucleation density of graphene. We observe that introducing O2 during growth significantly improves the graphene crystallinity while pre-dosing O2 before growth reduces the graphene nucleation density. These studies suggest that intermittent O2 exposure play a significant role in graphene growth, enabling scalable production of high-quality graphene.

We report here a successful fabrication of three-dimensional (3D) photoelectrodes fully coated with hydrothermally formed TiO2 nanotubes on multi-layered Ti mesh with significantly increased surface area. A near-vertical array of ~8 nm diameter nanotubes of TiO2 was also produced on the metallic surface of folded Ti mesh electrode. The multi-layered mesh was used as a 3D highly conductive electrode, as this architecture intuitively allows for light passage, reflections, and smooth water flow for possible continuous operation of water splitting reaction. By virtue of substantially increased surface area and more efficient light usage, significantly increased photocurrent densities were obtained.

The relationship between the oscillatory force and the depth-response during dynamic indentation was analyzed mathematically and investigated experimentally in ultrafine-grained Al–Zn alloys processed by high-pressure torsion. We have shown for the first time that the phase shift between the local oscillatory force and depth signal, caused by the internal friction, is correlated to the strain-rate sensitivity, which is a key parameter indicating the ductility of materials. This correlation enables a new application of dynamic nanoindentation for studying the rate-dependent deformation-mechanisms of materials from a novel aspect.

The advancement of lead-free piezoelectric nanogenerators (PENGs) for flexible electronics necessitates designing more efficient systems for improved energy storage capacity. In this light, the effects of patterning BaTiO3 nanotubes within PENG on the electromechanical properties of the device were investigated. The PENGs comprised a sandwich structure of Ti–BaTiO3–graphite–Ti encapsulated in polydimethylsiloxane. Four patterns of vertically aligned BaTiO3 nanotubes were synthesized via the hydrothermal conversion of selectively-anodized TiO2 nanotubes. The highest output voltage reached up to 1.9 V. Decreasing the nanotube array spacing and pattern diameter increased the lateral displacement of BaTiO3 therefore, increasing the output voltage of the device.

We investigated the connectivity of high-energy random grain boundaries through fractal analyses of specimens with different grain boundary (GB) microstructures in BFe10-1-1 copper–nickel alloy. It was found that the profile of maximum random boundary network possesses a fractal nature and more than one fractal dimension can exist. The fraction of special boundaries and grain size homogeneity can play an important role on GB character distribution. Here, GB microstructures are combined with quantitative materials structure–property relationship models to predict intergranular corrosion properties. The experimental results are accurately consistent with the theoretical predictions.