The development of thermoelectric measurement technology at nanoscale is a challenging task. Here, a novel MEMS-based dual temperature control (DTC) measurement method for thermoelectric properties of individual nanowires was proposed. Different from conventional thermal bridge testing devices, this DTC thermoelectric testing device can obtain the thermoelectric properties by independently control ambient temperature and temperature difference between two ends of the nanowires through two separate resistance thermometers without auxiliary heating devices. The reliability of the model and the testing accuracy were verified by accurately measuring the thermal conductivity, electrical conductivity, and the absolute value of the Seebeck coefficient of VO2 nanowires.

First principles simulations and global optimization predict new mode of binding of Pt clusters with defects on graphene that significantly enhances their stability. Pt clusters were found to firmly bind to monovacancies in configuration transacting the vacancy site, while retaining the integrity of the cluster. Diffusion calculations support tight anchoring of Pt cluster to monovacancy. Pt cluster adsorbed on pristine graphene or other common defects exhibit a different mode of adsorption and only decorate one side of graphene. This study reveals strong influence of defect chemistry on the structure and mobility of Pt nanoclusters adsorbed on graphene and have important implications for catalytic and gas sensing applications.

Nanoparticle-mediated drug delivery has the potential to overcome several limitations of cancer chemotherapy. Lipid polymer hybrid nanoparticles (LPHNPs) have been demonstrated to exhibit superior cellular delivery efficacy. Hence, doxorubicin (a chemotherapeutic drug)-loaded LPHNPs have been synthesized by three-dimensional (3D)-printed herringbone-patterned multi-inlet vortex mixer. This method offers rapid and efficient mixing of reactants yielding controllable and reproducible synthesis of LPHNPs. The cytotoxicity of LPHNPs is tested using two-dimensional (2D) and 3D microenvironments. Results obtained from 3D cell cultures showed major differences in cytotoxicity in comparison with 2D cultures. These results have broad implications in predicting in vitro LPHNP toxicology.

Gravity is commonly considered negligible when the surface tension is dominant; i.e., the Bond number is less than 1. In this paper, however, the authors present a technique in which drops slide over surfaces with zero effective gravity. Our study compared the sliding motion of water drops on hydrophilic and hydrophobic surfaces in scenarios: one in which effective gravity = 1 (1 g) and one in which it = 0 (0 g). The authors found that the lateral retention force was greater under 1 g than it was under 0 g. Also, the results showed that retention forces calculated by Furmidge equation are higher than the measured forces.

By electron-beam (e-beam) melting, we prepared 0.4 wt% carbon-infused copper (CuCv4), and a copper control without carbon addition (CuCv0). Scanning electron microscopy and helium ion microscopy (HIM) were performed on the as-solidified surface, fracture surface, and ion-polished surface of the CuCv4 sample. The results revealed that graphitic carbon flakes cover the as-solidified surface, and carbon nanoparticles and clusters exist in the fracture and ion-polished surfaces. HIM on the ion-polished surface revealed a unique ripple-shaped feature, which is possibly associated with the infusion of carbon nanoribbons in the copper matrix. The bulk densities were measured to be 8.86 and 8.53 g/cm3, which correspond to relative densities of 98.9% and 96.4% for the CuCv0 and CuCv4 samples, respectively. In addition, apparent electrical conductivities were measured to be 56.9 and 57.5 MS/m, respectively, for the e-beam melted CuCv0 and CuCv4 samples. These values correspond to true electrical conductivities of 100.5% IACS (International Annealed Copper Standard) and 107.4% IACS after correction for the porosity. Our results reveal remarkable promise of using covetic copper for the next generation conductors in energy applications from microelectronic devices to high-power transmission cables.

${\rm Au}_{25}\lpar {{\rm C}_6{\rm H}_{14}{\rm S}} \rpar_{18}{}^-$ icosahedron and [Au25(PPh)10(C6H14S)5Cl2]2+ bi-icosahedron clusters were synthesized. Ligand exchange reactions were carried out with a new coumarin-derived fluorophore (Cou-SH) to label both clusters. Labeled and unlabeled Au25 were compared and the changes in the electronic structure were determined. The labeled clusters showed marked changes in electronic states, as evidenced by the quenching in the UV region and enhancement in the near infrared. The quantum yield from Cou-SH decreased and the quantum yield from the labeled Au25 increased. Second, the authors observed changes in the electrochemical band gap.

In order to reveal the quantitative relationship between fatigue crack deflection path and cross-sectional grain boundary (GB) arrangement of metallic nanolayered composites (NLCs), a stochastic model was established based on the interface-dominant fatigue damage for the ultrafine-scale NLCs. The model indicates that the crack deflection length decreases with decreasing GB arrangement deviation and grain size of constituent layers. The observation and quantitative analysis of fatigue cracking behavior of the Cu/W multilayers with a layer thickness of 5 and 20 nm was conducted to verify the model.

Plasmonic waveguides can transport light while still confining it beyond the diffraction limit. Recently, crossing plasmonic waveguides have been suggested for the implementation of higher-density optical networks. However, suppressing undesirable scattering at their crossing point is still a challenging task because waveguides in these structures are physically connected. Here, we present an experimental demonstration of surface plasmon propagation on an overcrossing metallic waveguide fabricated by a pick-and-place method. By spatially separating the waveguides, the undesirable interaction at the interconnection can be suppressed. Our approach could be a powerful platform to achieve high-density integration of optical waveguides.

Lateral memristors consisting of planar Ag electrodes (with sub-micrometer separation) supported on thin films of amorphous zinc-tin-oxide have been characterized. After an initial filament-forming process, each device exhibited volatile, resistive switching. In the low resistance state, the transport mechanism and conductance depended on prior activity and on the imposed current limit, mimicking biologic synaptic plasticity. Microscopic observations performed on each device revealed nanoscale filaments between the electrodes. These filaments were subject to Rayleigh instability and exhibited relaxation times determined by their effective radii. The relaxation times and on:off resistance ratios suggest suitability for threshold switching selector devices.

We have investigated interfacial thermal resistance (ITR) between single-layer graphene and Cu substrate by using both experimental and numerical methods. For experiments, the micropipette sensing technique was utilized to measure the thermal conductivity of suspended graphene and temperature profile of supported graphene on Cu film subjected to heating with a point source continuous wave laser. The thermal conductivity of suspended single-layer graphene was measured to be 3492 ± 453 W/m°C from measurements of temperature profile on the suspended graphene. This intrinsic graphene thermal conductivity and the finite element method integrated with a multi-parameter fitting technique were used to estimate ITR between graphene and Cu film. In the multi-parameter fitting technique, the simulated temperature profile is compared with experimentally measured temperature profile on the supported graphene surface and the best-fitted parameters including thermal interface resistance was obtained. The estimated interface thermal resistance between single graphene and Cu substrate is 2.3 × 10−7 m2 K/W and the difference between experiment and simulation result during multi-parameter fitting is 6.9%.

We investigate the two-photon absorption characteristics of hemicyanine dyes that exhibit a one-photon absorption at around 500 nm. The dyes exhibited two-photon-induced fluorescence upon irradiation with an Yb-doped femtosecond fiber laser operating at 1030 nm. Among the dyes, 4-[4-[4-(dimethylamino)phenyl]-1,3-butadienyl]-1-ethyl-pyridinium perchlorate exhibited the most efficient two-photon-induced fluorescence at 1030 nm. Since these dyes possess cationic moiety, the dyes accumulated in the mitochondria of a living cell. Two-photon images of mitochondria were obtained by staining living HEK293 cells with these dyes. When 4-[4-[4-(dimethylamino)phenyl]-1,3-butadienyl]-1-ethyl-pyridinium perchlorate was employed, a two-photon-induced fluorescence image could be obtained even when a 3 mW fiber laser beam was used as the excitation source.

Lithium-ion capacitors utilizing graphite (G) and reduced graphite oxide (RGO) as negative electrode materials were investigated. Various reduction methods of graphite oxide were applied to compare properties of modified materials. The hybrid cells showed the energy density at mild current regimes of ca. 70–100 Wh/kg. However, at higher rates, only the capacitor with chemically RGO maintained this tendency. Moreover, the system demonstrated the energy density of 34 Wh/kg at a power density of 26 kW/kg. The electrochemical measurements were conducted in three-electrode systems to record responses of positive and negative electrodes separately.

Immune cells can be genetically engineered with a synthetic chimeric antigen receptor (CAR) to eliminate cancer cells, but clinical efficacy in solid tumors has been disappointing due in part to the immunosuppressive tumor microenvironment (TME). Additionally, the cost and logistical issues of personalized medicine necessitate the creation of an off-the-shelf CAR therapy. Synthetic biology tools were implemented in addressing these problems: an anti-mesothelin CAR, membrane-bound IL-15/IL-15Rα complex, and inducible caspase 9 “kill switch” were expressed in natural killer cells for tumor-targeting capabilities, immunostimulatory effects, and safety in treating a preclinical model of ovarian cancer with a renewable, allogenic cell therapy.

This research utilizes anatase TiO2 incorporated with lithium salt via a simple wet physical method to surface-modified the commercial graphite to form the lithium titanate/graphite composite coated with an amorphous carbon layer on its surface (the double core–shell structure) to enhance its surface conductivity. This double core–shell structure provides a stable specific capacity about 280 mAh/g under the high current density, 2.25 A/g with 15% capacity retention decay. Its intercalation potential is below 1 V that is much lower than that of 1.55 V, the intercalation potential of spinel Li4Ti5O12, to make higher power and energy density for a full cell.

ZnO-based oxides are promising for thermoelectric energy generation at elevated temperatures. We study electrical transport properties of Ni-doped ZnO applying the density functional theory, indicating increase of the electrical conductivity (σ) and decrease of the Seebeck coefficient (S) due to Ni-doping, in full accordance with experimental results. We calculate the temperature-dependent σ and S applying the Boltzmann transport theory, approximating the electron relaxation time, τe. Good agreement with experimental data is obtained considering both temperature and energy dependence of τe. This yields explicit expressions for τe and provides us with powerful predictive tool assessing electronic transport in ZnO.

We present the first characterization of strongly scale-dependent charge transport of a unique, hierarchical complex topology: an interconnected random network of silicon quantum dots (QDs) and nanowires. We show that this specific topology has different charge transport characteristics on the nanoscale and the microscale: photogenerated charge carriers tend to be confined inside the QDs and externally injected charge carriers flow preferably along the nanowires. The former enables expression of quantum confinement properties, and the latter mainly contributes to the good electrical conduction on the microscale. Our findings strongly suggest that this multifunctionality can be controlled and used in photovoltaic device applications.

Properly driving protein interactions with solid surfaces play a very important role in many natural processes, stimulating a great interest for the design of new biomaterials and medical devices. Despite the progress in this field, many further upgrades have to be achieved to better exploit the protein driving, in terms of control of amounts and conformation of the adsorbing proteins. In this paper, new biocompatible amino acid–calix[4]crown-5 bilayers were built as nano-templating surfaces, hosting a controlled number of anchoring sites, able to immobilize proteins in well-defined quantity, and the evaluated footprint data support the idea of oriented protein on analyzed substrates. The efficiency of the setup was tested for the particular case of antibacterial lysozyme adsorption on biocompatible surfaces.

Oligodepsipeptides (ODPs) with alternating amide and ester bonds prepared by ring-opening polymerization of morpholine-2,5-dione derivatives are promising matrices for drug delivery systems and building blocks for multifunctional biomaterials. Here, we elucidate the behavior of three telechelic ODPs and one multiblock copolymer containing ODP blocks at the air–water interface. Surprisingly, whereas the oligomers and multiblock copolymers crystallize in bulk, no crystallization is observed at the air–water interface. Furthermore, polarization modulation infrared reflection absorption spectroscopy is used to elucidate hydrogen bonding and secondary structures in ODP monolayers. The results will direct the development of the next ODP-based biomaterial generation with tailored properties for highly sophisticated applications.

Direct electrical measurement of single grain boundaries is performed for ZnO-based multilayer ceramic varistors with fine grains of 2 µm, using a nano-prober. The effect of ZnO grains on non-linearity is shown to be significant. The microstructure is comprised at least two non-linear types as good- and bad-junctions. The numerical ratio of good to bad is estimated to be about one (non-linearity exponent α max ≥ 10) to two (<10), which is independent of microstructural development as grain growth. The grain control of twinning as well as crystal orientation and donor concentration is considered effective in the further improvement.