In this article, a genetic algorithm (GA) is proposed as a solution for the path planning of unmanned aerial vehicles (UAVs) in 3D, both static and dynamic environments. In most cases, genetic algorithms are utilised for optimisation in offline applications; however, this work proposes an approach that performs real-time path planning with the capability to avoid dynamic obstacles. The proposed method is based on applying a genetic algorithm to find optimised trajectories in changing static and dynamic environments. The genetic algorithm considers genetic operators that are employed for path planning, along with high mutation criteria, the population of convergence, repopulation criteria and the incorporation of the destination point within the population. The effectiveness of this approach is validated through results obtained from both simulations and experiments, demonstrating that the genetic algorithm ensures efficient path planning and the ability to effectively avoid static and dynamic obstacles. A genetic algorithm for path planning of UAVs is proposed, achieving optimised paths in both static and dynamic environments for real-time tasks. In addition, this path planning algorithm has the properties to avoid static and moving obstacles in real-time environments.

The rising demand for air traffic will inevitably result in a surge in both the number and complexity of flight conflicts, necessitating intelligent strategies for conflict resolution. This study addresses the critical challenges of scalability and real-time performance in multi-aircraft flight conflict resolution by proposing a comprehensive method that integrates a priority ranking mechanism with a conflict resolution model based on the Markov decision process (MDP). Within this framework, the proximity between aircraft in a multi-aircraft conflict set is dynamically assessed to establish a conflict resolution ranking mechanism. The problem of multi-aircraft conflict resolution is formalised through the MDP, encompassing the design of state space, discrete action space and reward function, with the transition function implemented via simulation prediction using model-free methods. To address the positional uncertainty of aircraft in real-time scenarios, the conflict detection mechanism introduces the aircraft’s positional error. A deep reinforcement learning (DRL) environment is constructed incorporating actual airspace structures and traffic densities, leveraging the Actor Critic using Kronecker-factored Trust Region (ACKTR) algorithm to determine resolution actions. The experimental results indicate that with 20–30 aircraft in the airspace, the success rate can reach 94% for the training set and 85% for the test set. Furthermore, this study analyses the impact of varying aircraft numbers on the success rate within a specific airspace scenario. The outcomes of this research provide valuable insights for the automation of flight conflict resolution.

In order to improve the performance of $k - \omega $ SST model in turbomachinery, previous studies have used the machine-learning (ML) technique to obtain turbulence models (for example, the ML-RANS EQ model). However, these models do not lead to satisfactory results in complex flows in turbomachinery. In this study, we use non-equilibrium training dataset to obtain a new turbulence model (i.e., the ML-RANS TR-NE-EQ model). Calculations in various cases of turbine cascade flows show that ML-RANS TR-NE-EQ model performs obviously better than ML-RANS EQ model as well as $k - \omega $ SST model.

Aircraft play a major role in meeting the fast and efficient transportation needs of modern society, thanks to their advanced features. However, gas turbine engines used in aircraft have many negative effects on human health. One of the negative effects is the exhaust gases released by these engines to nature. In this study, it is discussed to present alternative models based on heuristic methods to reduce the emission values of the synthetic fuel mixture used in the combustion chamber of gas turbine engines. For this purpose, a model based on artificial neural networks (ANN) based on the back-tracking search optimisation (BSO) algorithm is proposed by using experimentally obtained emission values found in the literature. In the proposed model, the parameters of the optimum ANN structure are first determined by the BSO algorithm. Then, by using the optimum ANN structure, the most appropriate input values were found with the BSO algorithm, and the emission values were reduced. The simulation results have shown that the proposed method will be a fast and safe alternative method for reducing emission values.

The objective of this study was to investigate the effects of different cockpit primary flight display (PFD) interface designs on pilot cognitive efficiency and cognitive load. This study designed five optimised PFD interfaces and conducted interface cognition experiments to assess cognitive responses across six different PFD interface designs, including the original design. It compared various subjective and objective metrics across different interface designs and evaluated the impact of each design factor on cognitive task performance. The experimental results show that the PFD interface in the original interface design performs better under different flight symbol designs, and the interface with 50% increase in font size performs better among interface designs with different font sizes with relatively lower cognitive load. This study provides experimental support and optimization suggestions for the optimal design of cockpit PFD interface, which can help improve pilots’ perception and operational capabilities, and thus enhance task performance efficiency and flight safety. Future research can investigate the effects of various design factors on the cognitive effects of the interface to enhance the ongoing improvement and optimisation of interface design.

This paper describes a reverse engineering methodology so as to accomplish an aero-propulsive modelling (APM) through implementing a drag polar estimation for a case study jet aircraft in case of the absence of the thrust data of the aircraft’s engine. Since the available thrust force can be replaced by the required thrust force for the sustained turn, this approach allows the elimination for the need of the thrust parameter in deriving an aero-propulsive model utilising equations of motion. Two different modelling approaches have been adopted: (i) implementing the 6-DOF model data for sustained turn and climb flight to achieve induced drag model; and then incorporating the glide data to obtain the total drag polar model; (ii) using the 6-DOF model data together with introducing the effect of CL-α dependency. The error assessments showed that the derived CSA models were able to predict the drag polar values accurately, providing linear correlation coefficient (R) values equal to 0.9982 and 0.9998 for the small α assumption and CL-α dependency, respectively. A direct comparison between the trimmed CD values of 6-DOF model and the values predicted by the CSA model was accomplished, which yielded highly satisfactory results within high subsonic and transonic CL values.

Contrails are a major contributor to the climate effect of aviation. Mitigation efforts and technological improvements aim to reduce the contrail climate effect. Many currently discussed innovations (like using sustainable aviation fuels (SAFs) or hydrogen) affect the physical processes and phenomena during contrail formation. Hence, understanding and analysing contrail formation is of great importance in the context of climate research. Ice crystal formation in a nascent contrail is completed within the first seconds after the engine exhaust is emitted. In the past, numerical models treating this early stage typically involved either a 3D or 0D approach. Whereas 3D models are computationally expensive, restricting the number of simulations that could be performed, less expensive 0D models allow to explore a larger parameter space but neglect plume heterogeneity and use a prescribed plume dilution. We present the new dynamical framework RadMod for contrail formation simulations that describes the evolution of a turbulent round jet emitted from an aircraft engine. Relative to large-eddy simulation (LES) or Reynolds-averaged Navier-Stokes (RANS) 3D models of contrail formation, our model is computationally less expensive, enabling extensive parameter studies. The model accounts for the mixing of the hot and moist exhaust air with the cold ambient air through the solution of the two-dimensional advection-diffusion equation of momentum, temperature, and water vapour. The validation of our model is conducted through comparisons with empirical relationships and CFD results. In the near future, this model will be combined with an existing microphysical model, resulting in a contrail formation model of intermediate complexity.

In the past few decades, substantial work has been directed towards the design of aircraft structures that maximise fuel efficiency, improve performance and curtail emissions. Aeroelastic optimisation offers an effective way to devise lightweight and fuel efficient structures, with structural stability constraints often driving the design. To date, the aeroelastic optimisation community has relied mostly on linear buckling predictions for the evaluation of structural stability constraints, mainly because of their conservativeness, computational efficiency and simplicity of implementation. This approach typically leads to overly conservative buckling margins, and this over-conservativeness places a glass ceiling over the load carrying capacity of wing structures, consequently restricting the exploration of regions within the design space where considerable weight savings could be achieved.

By contrast to previous works that predominantly rely on linear buckling constraints, the present paper introduces a method to incorporate nonlinear structural stability analysis into aeroelastic optimisations of wingbox-like structures. The method relies on the evaluation of the positive-definiteness of the tangent stiffness matrix, which is an indicator of structural stability. The sign of the stiffness eigenvalues is monitored while tracing the load-displacement equilibrium paths by means of the arc-length method, thus pinpointing the onset of instability. The proposed constraint is tested in a proof of concept structural optimisation of an idealised version of the CRM wingbox. This optimisation shows a $10.9{\rm{\% }} $ reduction in mass with respect to a baseline design that is optimal with a linear buckling approach, promising great potential for application to more realistic aeroelastic optimisations.

The variable stator vanes (VSV) are a set of typical spatial linkage mechanisms widely used in the variable cycle engine compressor. Various factors influence the angle adjustment precision of the VSV, leading to the failure of the mechanism. The reliability analysis of VSV is a complex task due to the involvement of multiple components, high dimensionality input and computational inefficiency. Considering the hierarchical characteristics of VSV structure, we propose a novel multi-layer Kriging surrogate (MLKG) for the reliability analysis of VSV. The MLKG combines multiple Kriging surrogate models arranged in a hierarchical structure. By breaking the problem down into more minor problems, MLKG works by presenting each small problem as a Kriging model and reducing the input dimension of the sub-layer Kriging model. In this way, the MLKG can capture the complex interactions between the inputs and outputs of the problem while maintaining a high degree of accuracy and efficiency. This study proves the error propagation process of MLKG. To evaluate MLKG’s accuracy, we test it on two typical high-dimensional non-linearity functions (Rosenbrock and Michalewicz function). We compared MLKG with some contemporary KG surrogate modeling techniques using mean squared error (MSE) and R square (${R^2}$). Results show that MLKG achieves an excellent level of accuracy for reliability analysis in high-dimensional problems with a small number of sample points.

Aiming at the problem of fast and consensus obstacle avoidance of multiple unmanned aerial systems in undirected network, a multi-quadrotor unmanned aerial vehicles UAVs (QUAVs) finite-time consensus obstacle avoidance algorithm is proposed. In this paper, multi-QUAVs establish communication through the leader-following method, and the formation is led by the leader to fly to the target position automatically and avoid obstacles autonomously through the improved artificial potential field method. The finite-time consensus protocol controls multi-QUAVs to form a desired formation quickly, considering the existence of communication and input delay, and rigorously proves the convergence of the proposed protocol. A trajectory segmentation strategy is added to the improved artificial potential field method to reduce trajectory loss and improve the task execution efficiency. The simulation results show that multi-QUAVs can be assembled to form the desired formation quickly, and the QUAV formation can avoid obstacles and maintain the formation unchanged while avoiding obstacles.

This paper aims to explore the feasibility of providing boundary layer propulsion and flow control by means of embedded aerofoils that are oscillating in the pure plunge mode. To this end, Navier-Stokes calculations of the low-speed flow over a flat plate with an oscillating small foil in close vicinity to the plate were performed to determine the influence of the wall distance, Reynolds number, and reduced frequency on the aerofoil thrust. The simulations were extensively validated against water tunnel experiments at Reynolds numbers between 440 to 5,940. Good agreement was obtained in terms of mean streamwise velocity profiles and the vortical wake patterns. Results indicate that the thrust increases from its value in unbounded flow with decreasing distance from the plate. The propulsive efficiency exhibits a consistent peak at a non-dimensional plunge velocity of about 0.55. For wall distances between one-half to one chord lengths, vortex pairs are shed in a slightly upward deflected direction independent of the starting motion of the aerofoil. As the wall distance increases further, these vortex pairs change into the well-known reverse Karman vortex street. Example calculations for a flat plate with two foils mounted close to the plate trailing edge and oscillating in counterphase confirm the device’s efficacy.

Friction stir welding (FSW) is a method of solid-state welding used to connect difficult-to-weld materials, such as aluminium alloy and magnesium alloy that cannot be joined using conventional welding techniques. This paper investigates the impact of FSW parameters on the corrosion characteristics of friction stir-welded AA2014-T6 aluminium alloy. Experiments were conducted in accordance with the Taguchi L9 orthogonal array by varying tool rotation speed, weld speed, and axial force across three levels. The FSW joints of the aluminium alloy AA2014-T6 were subjected to corrosion test using the electro-chemical workstation CHI660C. The Tafel plots and the corrosion rates were obtained from the corrosion tests. It was observed from the analysis of variance (ANOVA) results of the corrosion rates, that the tool rotation speed is the most persuading factor in controlling the corrosion rate. The scanning electron microscope (SEM) images of the corroded samples were analysed for the presence of pitting spots and its density.

The fault-tolerant control issue of aircraft engines with actuator dynamics and faults is investigated in this paper. By proposing a novel intelligent sliding mode fault-tolerant control (ISMFTC) method, which combines an adaptive dynamic programming (ADP) sliding surface with Grey Wolf Optimizer (GWO) for controller parameter optimisation, the goal is to achieve quality steady-state and dynamic performance in aircraft engines while maintaining strong fault-tolerance properties. Firstly, by considering not only actuator dynamics but also actuator faults, an uncertain nonlinear cascaded model of aircraft engines is developed according to characteristic of aircraft engines and their actuators. Secondly, an ADP-based sliding surface is proposed for considered aircraft engine uncertain nonlinear cascaded system. It can obtain a certain sense of optimised performance, and could be solved by ADP strategy off-line as well. Thirdly, fault-tolerant controller is obtained on the basis of sliding mode theory and adaptive fault estimation law, namely, ADP-based ISMFTC controller. Meanwhile, GWO is integrated into the investigation of ADP-based ISMFTC controller, optimised designable control parameters are obtained subsequently. Besides, robustness analysis is elaborated according to Lyapunov theory, fault estimation error is bounded and states of closed-loop system are uniformly ultimately bounded. Simulation on a twin-shaft turbofan aircraft engine, indicates the effect of proposed ADP-based ISMFTC method.

The current emphasis in aerospace component development is on creating safe, reliable and cost-effective technologies. However, the intricate design of stage separation systems renders component reliability a critical factor in determining mission success or failure. One of the technical challenges involves the development of various aerospace mechanisms, such as payload separation, heavy propulsion system separation, ejection of auxiliary components and detachment of rigid components. These stage separation mechanisms commonly employ pyrotechnic devices, which, by their operational nature, impart shock to the spacecraft, potentially causing damage or adverse effects on flight instruments. Therefore, it is imperative to explore multiple viable concepts aimed at reducing shock and experimentally ascertain the impact of shock using diverse shock attenuation techniques. While existing literature primarily addresses shock attenuation with distance from the shock source, limited attention has been given to diminishing shock at the location of the shock-generating element. This study employed various shock-attenuating devices, including dampers, metallic foam structures, viscous materials and dampeners, to assess the effectiveness of shock reduction. Furthermore, the study investigated shock reduction resulting from the elimination of rigid connections, such as bolted joints, from pyro-actuated mechanisms. Through a series of experiments, a conclusive analysis was conducted to determine the approach for achieving a substantial reduction in pyro shock.

The world is currently undergoing a technological transformation with numerous innovative concepts emerging. This shift is driven by remarkable advancements in artificial intelligence and the urgent need for decarbonisation. With this comes a growing demand for skilled engineers who can actively contribute at any stage within the life cycle of a product. This can be the generation of new concepts at low Technology Readiness Levels or contributing actively to their development and operational safety. This paper explores the integration of a 1-day practical activity to reinforce theoretical concepts learned within a classroom-based environment. Small groups of students were given the opportunity of engaging with a small helicopter engine (Rolls-Royce Gnome engine) through the disassembly and reassembly of the exhaust and power turbine section while following the manufacturer’s manual and ensuring industrial norms for safe practice. This hands-on activity included an introduction to tooling, a Gnome familiarisation activity, and an introduction to inspection techniques. Based on the feedback recorded, the students experienced a notable improvement in their basic understanding by effectively reinforcing knowledge acquired within the classroom through active engagement with an actual gas turbine engine.

A simplified configuration was developed to facilitate the mode transition process within an over-under Turbine-Based Combined Cycle (TBCC) inlet. Leveraging dynamic mesh technology, an unsteady numerical simulation of the mode transition was conducted, emphasising the flow characteristics of the mode transition and the impact of key similarity criteria numbers. The findings indicate that at an incoming Mach number of 2.0, the mode transition is paired with a continuous alteration in the capture mass flow of the high-speed duct. This continual change instigates the inlet unstarting, with subsequent flow characteristics being contingent on the historical effect, exhibiting a degree of hysteresis characteristics. When the scale effect is considered, it is observed that a larger model scale results in higher Reynolds (Re) and Strouhal (St) numbers. This directly contributes to a notable delay in the unstart moment, a decrease in the unstart interval, and an enlargement of the hysteresis loop. An examination of control variables reveals that the Re number marginally influences mode transition characteristics, while the St number’s effect constitutes approximately 90% of the scale effect. This conclusively demonstrates that the St number is the predominant similarity criterion number in the mode transition process.

Interlaminar delamination damage is a common and typical defect in the context of structural damage in carbon fiber-reinforced resin matrix composites. The technology to identify such damage is crucial for improving the safety and reliability of structures. In this paper, we fabricated carbon fiber-reinforced composite laminates with different degrees of delamination damage, conducted static load experiments on them and used femtosecond fiber Bragg grating sensors (fsFBG) to determine their structural state to investigate the effects of delamination damage on their performance. We constructed a model to identify damage based on the deep residual shrinkage network, and used experimental data to enable it to identify varying degrees of delamination damage to carbon fiber-reinforced composites with an accuracy of 97.98%.

Critical space assets require continuous monitoring to prevent potential losses. Auxiliary satellites protect these assets by observing and tracking approaching targets. Although observation satellites can make rapid autonomous onboard decisions, they face challenges due to limited computational capacity. The two mainstream command and control methods currently available do not meet the demands of onboard decision-making. Highly procedural decision-making methods require extended decision times, while rapid-response intuitive or heuristic methods carry significant error risks. To address this, this paper proposes a multi-granularity decision-making method for optical space surveillance satellites. First, multi-granularity relative orbit determination algorithm models and multi-granularity impulsive orbit manoeuver algorithm models were developed. Based on these models, a granularity selection method for sequential three-way decisions is proposed. In non-emergency situations, fine-granularity models are preferred to conserve fuel, while in emergency situations, coarse-granularity models are used to enhance decision-making speed and reduce positional deviations caused by the manoeuvering game. In random multi-scenario tests, the proposed method demonstrates lower average terminal positional deviations and fuel consumption compared to single-granularity (highly procedural or rapid-response) and random-granularity methods.

In a competitive market, airlines continually seek solutions that can reduce their operational costs. Flight path optimisation is a commonly pursued approach to this but requires a large amount of data about the flight environment including the weather information, the aircraft performance and the air traffic control (ATC) requirements. Existing programmes require the user to provide this aircraft performance data in advance and are incapable of generating the information on their own. In this study, using a multidisciplinary approach and numerical optimisations, a novel standalone flight path optimiser (SAFPO) solution is proposed and developed to choose the best flight path for a flight between two points in accordance with the cost objectives. SAFPO uses its own performance calculator, predefined ATC routes, and known weather information to find the optimum flight path which minimises fuel consumption and/or flight time. The aerodynamic characteristics of the aircraft are determined using a validated semi-empirical programme called MAPLA, previously developed for light aircraft analysis. Furthermore, the optimisation process consists of a multidisciplinary-feasible (MDF) framework that employs a genetic algorithm (GA) optimiser. The resulting performance characteristics of the aircraft and the optimisation process are compared with the actual information provided within the flight manual of a Beechcraft Baron G58 aircraft. The optimisation results show that SAFPO can be used to make advances in the daily operations of small and local airlines suffering from a lack of aircraft performance data and help them to choose the scenario that best accomplishes their cost objectives.

This paper develops a novel full-state-constrained intelligent adaptive control (FIAC) scheme for a class of uncertain nonlinear systems under full state constraints, unmodeled dynamics and external disturbances. The key point of the proposed scheme is to appropriately suppress and compensate for unmodeled dynamics that are coupled with other states of the system under the conditions of various disturbances and full state constraints. Firstly, to guarantee that the time-varying asymmetric full state constraints are obeyed, a simple and valid nonlinear error transformation method has been proposed, which can simplify the constrained control problem of the system states into a bounded control problem of the transformed states. Secondly, considering the coupling relationship between the unmodeled dynamics and other states of the controlled system such as system states and control inputs, a decoupling approach for coupling uncertainties is introduced. Thereafter, owing to the employed dynamic signal and bias radial basis function neural network (BIAS-RBFNN) improved on traditional RBFNN, the adverse effects of unmodeled dynamics on the controlled system can be suppressed appropriately. Furthermore, the matched and mismatched disturbances are reasonably estimated and circumvented by a mathematical inequality and a disturbance observer, respectively. Finally, numerical simulations are provided to demonstrate the effectiveness of the proposed FIAC strategy.