In electron beams where space charge plays an important role in the beam transport, the beams’ transverse and longitudinal properties will become coupled. One example of this is the transverse–longitudinal correlation produced in a current-modulated beam generated in a DC electron gun, formed through the competition between the time-dependent radial space charge force and the time-independent radial focusing force. This correlation will cause both the slice radius and divergence of the beam extracted from the gun to depend on the slice current. Here we consider the transport of such a beam in a linearly tapered solenoid focusing channel. Transport performance was generally improved with longer taper lengths, minimal initial correlation between slice divergence and slice current, and moderate degrees of initial correlation between initial slice radius and slice current. Performance was also generally improved with lower slice emittances, although surprisingly transport was improved by slightly increasing the assumed slice emittance in certain limited circumstances.

Effective suppression of transverse stimulated Raman scattering (TSRS) in a large-aperture potassium dihydrogen phosphate (KDP) crystal is an important scientific and technical problem in high-intensity laser research and applications. In this work, a method to suppress TSRS using pulse stacking is proposed. The method suppresses TSRS significantly, with greater numbers of subpulses producing more obvious suppression effects, and the threshold intensity growth rate of the 3ω laser in the KDP crystal reaches up to about 1.9 when the stacked pulse contains four subpulses. This suppression effect is attributed to the fact that the polarization directions of adjacent subpulses are perpendicular to each other. The method can be used to suppress other nonlinear effects, including transverse stimulated Brillouin scattering in large-aperture optical devices and stimulated rotational Raman scattering in long air paths.

We investigate an ionization injection scheme in a “weakly” non-linear regime of a wakefield, driven by sub-TW, few-cycle laser pulses in a single-stage, high-Z gas. This medium simultaneously provides the background wake fluid electrons from its lower ionization states and the necessary dephased electrons from its higher ionization states. Two dimensional-particle-in-cell simulations show the generation of relativistic electron beamlets having up to 15 MeV peak energy, with a narrow energy-spread and sub-fs duration. Since the currently-available sub-TW, few-cycle laser systems operate at kHz repetition rates, the presented scheme is capable of producing kHz attosecond electron bunches and their associated radiations which can find unique applications, for instance, in attosecond diffraction and microscopy.

Efficient electron acceleration by a linearly chirped ultrashort laser pulse in vacuum is investigated using the particle swarm optimization method. By applying this method for optimizing the initial parameters of the laser pulse, a pronounced increase in final energy gain of the electron is obtained compared to that expected from the successive optimization method. Our results also suggest that the value of the optimal chirp parameter is independent of laser polarization and the energy gain could be insensitive to the sign of this parameter when the initial phase is optimally adjusted. In addition, utilizing the chirped laser pulse with optimized conditions for acceleration of an electron bunch reveals that the energy spectrum is shifted to considerably higher energies and the spatial distribution is significantly improved in a polarization-dependent manner.

Flux waveforms of aluminum cluster beams supplied from a laser-ablation cluster source were precisely investigated under various source conditions such as background pressure, ablation laser intensity, and nozzle structure. A time-of-flight mass spectroscopy revealed that aluminum clusters with sizes up to 200 were generated and the amount of the clusters could be maximized by choosing a proper background pressure (~2 MPa) and an ablation laser fluence (~40 mJ/cm2). Flux waveforms of clusters having specific sizes were carefully reconstructed from the observed mass spectra. It is found that the pulse widths of the aluminum cluster beams were typically about 100 µs and much smaller than that of the monoatomic aluminum beam, indicating that the cluster formation was limited in a relatively small volume in the laser-ablated vapor. Introducing a conical nozzle having a large open angle was also found to enhance the cluster beam velocity and reduce its pulse width. A velocity measurement of particles in the cluster beam was conducted to examine the velocity spread of the supplied clusters. We found that the aluminum clusters were continuously released from the source for about 100 µs and this release time mainly determined the pulse width of the cluster beam, suggesting that controlling the behavior of an ablated vapor plume in the waiting room of the cluster source holds the key to drastically improving the cluster beam flux.

In this paper, the possibility of using neural networks for fast tomographic reconstructions of tokamak plasma soft X-ray (SXR) emissivity is investigated. Indeed, the radiative cooling of heavy impurities like tungsten could be detrimental for the plasma core performances of ITER, thus developing robust and fast SXR diagnostic tools is a crucial issue to monitor the impurities and to mitigate in real-time their central accumulation. As preliminary work, a database of emissivity phantoms with associated synthetic measurements is used to train the neural network to solve the inversion problem. The inversion method, training process, and first tomographic reconstructions are presented with the perspectives about our future work.

Study of even harmonic generation resulting from propagation of whistler pulse in homogeneous high-density quantum plasma immersed in an externally applied magnetic field, using the recently developed quantum hydrodynamic model is presented. The effects of quantum Bohm potential, quantum statistical pressure, and electron spin have been taken into account. The field amplitude of even harmonic of the whistler with respect to fundamental wave and the conversion efficiency for phase-mismatch has been analyzed. The conversion efficiency of harmonic radiation depends on the plasma electron density, magnetic field strength as well as the intensity of whistler pulse. The efficiency increases significantly with an increase in plasma density, magnetic field and whistler wave intensity. Higher conversion efficiency is observed in degenerate plasma for lower values of the static magnetic field as compared with classical plasma.

We study the setting up of relativistic ponderomotive non-linearity in an under-dense collisionless cold plasma. Using the fluid model, coupled system of equations of the laser beam and electron plasma oscillations has been derived. We present the numerical simulation for this coupled system of equations, when the coupling arises through relativistic ponderomotive non-linearity. The filamentation of the laser beam has been found to vary appreciably with perturbation wave number. The results show that with time, localized structures become more complex and the plasma oscillation frequency spectra have several harmonic peaks at terahertz frequencies when the electron plasma frequency is in terahertz range and laser frequency is around 2.35 × 1015 rad/s. We also present the semi-analytical model to capture the underlying physics.

The generation of high-order harmonics in ultraviolet spectral range by targets of periodic modulation interacting with relativistic, high contrast laser pulse (Iλ2 = 1020 W/cm2 · μm2) was investigated experimentally and numerically. The spectral intensity of the 2nd- and 3rd-order harmonic emission from grating of different periodicities (250, 410, and 480 nm) is presented. The enhancement of the 3rd harmonic order compared with 2nd was observed for a grating of 480 nm periodicity. The experimental results indicate the role of the grating periodicity on the emission efficiency of different higher order harmonics in the UV spectral range. The higher order harmonics are emitted at the grating surface separated from the specular reflection of the laser pulse, due of the interference effects. In addition, 2D numerical PIC simulations demonstrate a complex angular distribution of the higher harmonics (HH) spectral intensity and confirm the strong dependence of the HH efficiency of a specific order on the grating periodicity, as observed experimentally. These special features of the high harmonic emission by periodically modulated targets open the route toward the control of HH spectral composition and of the emission efficiency of the lower order harmonics.

Ignition with the help of a shock wave is performed by the interaction of accelerated plasma block by a petawatt-picosecond (PW-ps) laser, with a solid-state density fuel that it is a new possibility for achieving controlled fusion by inertial confinement. The unexpected production of plasma blocks provides new access to the ignition of solid-state density fuel according to the Chu hydrodynamic model. When the produced plasma block by the PW-ps laser hits the main fuel due to the density differences between the plasma block and the main fuel of the shock wave, this progressive wave increases the density of solidified fuels and reduces the energy of the ignition threshold and increases the flammability. In this study, a new discovery of shock waves has been observed leading to the resonance phenomenon. Nuclear heat shock waves resonance in the side-on ignition of fuel in the internal layer of fuel at x ≠ 0 appears from the exact solution of the hydrodynamic equations with respect to the density profile. This important finding achieves the required ignition temperature for solid-state fuel deuterium–tritium (D–T) in certain energies, with a significant increase due to the resonance of thermonuclear waves. This discovery will facilitate practical experiments on the ignition of advanced solid-state fuels with the accelerated plasma blocks by a PW-ps laser at certain energies.

The use of targets with surface structures for laser-driven particle acceleration has potential to significantly boost the particle and radiation energies because of enhanced laser absorption. We investigate, via experiment and particle-in-cell simulations, the impact of micron-scale surface-structured targets on the spectrum of electrons and protons accelerated by a picosecond laser pulse at relativistic intensity. Our results show that, compared with flat-surfaced targets, structures on this scale give rise to a significant enhancement in particle and radiation emission over a wide range of laser–target interaction parameters. This is due to the longer plasma scale length when using micro-structures on the target front surface. We do not observe an increase in the proton cutoff energy with our microstructured targets, and this is due to the large volume of the relief.

Thermal imaging diagnostics was used as a surface temperature mapping tool to characterize the energy density distribution of a high-intensity pulsed ion beam. This approach was tested on the TEMP-6 accelerator (200–250 kV, 150 ns). The beam composition included carbon ions (85%) and protons, and the energy density in the focus was 5–12 J/cm2. Targets of stainless steel, titanium, brass, copper, and tungsten were examined. Our observations show that the maximum energy density measured with the thermal imaging diagnostics considerably exceeds the ablation threshold of the targets. An analysis of the overheating mechanisms of each target was carried out, including metastable overheating of the target to above its boiling temperature during rapid heating; formation, migration, and the subsequent annealing of fast radiation-induced defects in the target under ion beam irradiation. This expands the range of energy density measurement for this thermal imaging diagnostics from 2–3 J/cm2 up to 10–12 J/cm2 but introduces error into the results of measurement. For a stainless steel target, this error exceeds 15% at an energy density of more than 4 J/cm2. A method of correcting the results of the thermal imaging diagnostics is developed for a pulsed ion beam under conditions of intense ablation of the target material.

A scheme of phase-matched terahertz generation by beating two co-propagating lasers in magnetized plasma, in the presence of a magnetosonic wave (MSW), is developed. The beat frequency ponderomotive force of the lasers imparts an oscillatory drift to electrons. The electron drift velocity couples with the electron density perturbation associated with the MSW to produce an irrotational nonlinear current $\left(\nabla \times {\vec J}\;{}^{\rm NL}\ne 0\right)$. The beat current density resonantly excites a THz (Terahertz) radiation when the phase-matching conditions are satisfied. The MSW mediates the phase matching. At 9.6 and 10.6 µm wavelengths, and background magnetic field of 285 kG, one may achieve normalized THz wave amplitude of the order of 10−3 and one obtains the ratio of THz power to pump power of the order of 10−6.

Research results of luminescence spectra of noble gases and Ar–Xe, Ar–Kr, and Kr–Xe mixtures under the excitation by products of nuclear reaction in the core of a stationary nuclear reactor with 0.87 × 1014 n/cm2s thermal neutron flux are described in the article. The emission spectra of noble gases are similar to the obtained spectrum under the excitation by the 40Ar+7 ion beam from the DC-60 accelerator. Bands in spectra of the binary mixtures of noble gases are connected with the radiation on heteronuclear ion molecule transitions. The appearance of the lines of alkali metal atoms at the temperature increase of gas chamber is explained by sputtering of the lithium layer via nuclear reaction products as well as ionized and excited particles of the buffer gas.

This paper presents a scheme for second harmonic generation (SHG) of q-Gaussian laser beam in plasma channel created by ignitor heater technique. The ignitor beam creates plasma by tunnel ionization of air. The heater beam heats the plasma electrons and establishes a parabolic density profile. The third beam (q-Gaussian beam) is guided in this plasma channel under the combined effects of density nonuniformity of the plasma channel and relativistic mass nonlinearity of the plasma electrons. The propagation of q-Gaussian laser beam through the plasma channel excites an electron plasma wave at pump frequency that interacts with the incident laser beam to produce its second harmonics. The formulation is based on finding the numerical solution of the nonlinear Schrodinger wave equation for the fields of the incident laser beams with the help of moment theory approach. Particular emphasis is put on dynamical variations of the spot size of the laser beams and conversion efficiency of the second harmonics with distance of propagation.

The formation of a collisional shock wave by the light pressure of a short-laser pulse at intensities in the range of 1018–1023 W/cm2 is considered. In this regime the thermodynamic parameters of the equilibrium states, before and after the shock transition, are related to the relativistic Rankine–Hugoniot equations. The electron and ion temperatures associated with these shock waves are calculated. It is shown that if the time scale of energy dissipation is shorter than the laser pulse duration a collisional shock is formed. The electrons and the ions in the shock-heated layer may have equal or different temperatures, depending on the laser pulse duration, the material density and the laser intensity. This shock wave may serve as a heating mechanism in a fast ignition scheme.

We present a broad study of linear, clustered, noble gas puffs irradiated with the frequency doubled (527 nm) Titan laser at Lawrence Livermore National Laboratory. Pure Ar, Kr, and Xe clustered gas puffs, as well as two mixed-gas puffs consisting of KrAr and XeKrAr gases, make up the targets. Characterization experiments to determine gas-puff density show that varying the experimental parameter gas-delay timing (the delay between gas puff initialization and laser-gas-puff interaction) provides a simple control over the gas-puff density. X-ray emission (>1.4 keV) is studied as a function of gas composition, density, and delay timing. Xe gas puffs produce the strongest peak radiation in the several keV spectral region. The emitted radiation was found to be anisotropic, with smaller X-ray flux observed in the direction perpendicular to both laser beam propagation and polarization directions. The degree of anisotropy is independent of gas target type but increases with photon energy. X-ray spectroscopic measurements estimate plasma parameters and highlight their difference with previous studies. Electron beams with energy in excess of 72 keV are present in the noble gas-puff plasmas and results indicate that Ar plays a key role in their production. A drastic increase in harder X-ray emissions (X-ray flash effect) and multi-MeV electron-beam generation from Xe gas-puff plasma occurred when the laser beam was focused on the front edge of the linear gas puff.

We present results of 2D particle-in-cell (PIC) simulations of carbon ion acceleration by 10 petawatt (PW) laser pulses, studying both circular polarized (CP) and linear polarized (LP) pulses. We carry out a thickness scanning of a solid carbon target to investigate the ideal thickness for carbon ion acceleration mechanisms using a 10 PW laser with an irradiance of 5 × 1022 W cm−2. The energy spectra of carbon ions and electrons and their temperature are studied. Additionally, for the carbon ions, their angular divergence is studied. It is shown that the ideal thickness for the carbon acceleration is 120 nm and the cutoff energy for carbon ions is 5 and 3 GeV for CP and LP pulses, respectively. The corresponding carbon ions temperature is ~1 and ~0.75 GeV. On the other hand, the energy cutoff for the electrons is ~500 MeV with LP and ~400 MeV with CP laser pulses. We report that the breakout afterburner mechanism is most likely causing the acceleration of carbon ions to such high energies for the optimal target thickness.

The cryogenic system for maintaining a target at a constant temperature in the range 5–25 K after shutting off the pulse tube (PT) cryogenic refrigerator is developed and tested. The temperature stability at the sample is ±2 mK for at least 20 hours. The cryogenic setup consists of cryostat, PT cryocooler, liquid helium vessel, helium gas supply, thermo-radiation shield, thermal resistance. The system provides 0.25 W of cooling power at the target. The appropriate thermal resistance should be used for different temperatures. The designed operation mode is 3 minutes off and 15 minutes on. The deactivation of PT cryocooler allows to achieve the target position stability of 1 micrometer or less during the X-ray characterization. The effect of neutron-shield was estimated using Monte-Carlo simulation.

A high energy electron density modulator from a high-intensity laser standing wave field is studied herein by investigating the ultrafast motion of electrons in the field. Electrons converge at the electric field antinodes, and the discrete electron density peaks modulated by the field located at the corresponding laser phases of kx = nπ, (n = 0, 1, 2, …), that is, the modulation period is 1/2 the wavelength of the individual laser. We also discussed the influence of the laser parameters such as laser intensity and waist size on the beam modulator. It is shown that a long interaction length (waist) or sufficiently high field intensity is essential for relativistic electron density modulation.