We have experimentally investigated the collisionless shock acceleration of ions via the interaction of a relativistic intensity (3 × 1019 W/cm2), 1.053 µm wavelength laser pulse with an underdense plasma. This plasma is formed through the use of a novel cluster jet design that allows for control of the plasma peak density and front scale length without the use of additional plasma-forming laser pulses. When the front density scale length of the target plasma is less than 60 µm, the laser pulse (1 J, 400 fs) is capable of launching an electrostatic shock wave that accelerates a proton beam. This beam is shown to have a narrow divergence angle of 0.8°, a peak flux of 14 × 106 protons/sr with an ion energy exceeding 440 keV. Particle-in-cell simulations indicate this narrow ion beam is produced by converging shocks generated via filamentation of the laser pulse in high-density (near critical) plasma.

The proton–boron ${}^{11}{\text{B}}\left( {p,\alpha } \right)2\alpha $ reaction (p-11B) is an interesting alternative to the D-T reaction ${\text{D}}\left( {{\text{T}},{\text{n}}} \right)\alpha $ for fusion energy, since the primary reaction channel is aneutronic and all reaction partners are stable isotopes. We measured the α production yield using protons in the 120–260 keV energy range impinging onto a hydrogen–boron-mixed target, and for the first time present experimental evidence of an increase of α-particle yield relative to a pure boron target. The measured enhancement factor is approximately 30%. The experiment results indicate a higher reactivity, and that may lower the condition for p-11B fusion ignition.

A partition calculation method (PCM) for calculating the diffraction efficiency of multilayer Fresnel zone plate with high aspect ratio is proposed. In contrast to the traditional theory, PCM designs and evaluates Fresnel zone plate (FZP) considering material pairs, all zone widths, thicknesses and X-ray energy more completely. The results obtained through PCM are validated by comparing them with the complex amplitude superposition theory and coupled wave theory numerical results. The PCM satisfies the requirements of the theoretical investigation of FZP with small outermost zone width (drN) and large thickness (t). Combining proper numerical analysis with the experimental conditions will present a great potential to break through the imaging performance of X-ray microscopy.

The interaction of focused high power laser beam with solid targets leads to acceleration of charged particles among other by non-linear effects in the plasma. In this experiment, the hot electrons are characterized from the interaction of sub-nanosecond and kilo-joule class laser pulse with thin metal foil targets (Cu, Ta, Ti, Sn, Pb). The energy distribution functions of electrons were measured by angularly resolved multichannel electron spectrometer. The hot electron temperatures were observed in range from 30 to 80 keV for laser intensities between ${\sim}10^{15}$ and $3 \times 10^{16}\ \mathrm{W\,cm^{-2}}$. The measured energy distribution and electron temperature were compared with published results and known scaling laws at higher laser intensities. For foil targets of different materials, the temperature and flux of hot electrons were scaled with target thickness in the range of 1–100 $\unicode{x03BC}\mathrm{m}$ from low Z to high Z materials where Z is the atomic number. The profile of conversion efficiency from laser energy to hot electrons is discussed in the energy range from 100 to 600 J. For the given laser and target parameters, the nonlinear behaviour of conversion efficiency and relevant physics are also described in detail.

Laser-driven X-rays as probes for high-energy-density physics spans an extremely large parameter space with laser intensities varying by 8 orders of magnitude. We have built and characterized a soft X-ray source driven by a modest intensity laser of 4 × 1013 W/cm2. Emitted X-rays were measured by diamond radiation detectors and a filtered soft X-ray camera. A material-dependence study on Al, Ti, stainless steel alloy 304, Fe, Cu and Sn targets indicated 5-μm-thick Cu foils produced the highest X-ray yield. X-ray emission in the laser direction and emission in the reverse direction depend strongly on the foil material and the thickness due to the opacity and hydrodynamic disassembly time. The time-varying X-ray signals are used to measure the material thinning rate and is found to be ∼1.5 μm/ns for the materials tested implying thermal temperature around 0.6 eV. The X-ray spectra from Cu targets peaks at ∼2 keV with no emission >4 keV and was estimated using images with eight different foil filters. One-dimensional hydrodynamic and spectral calculations using HELIOS-CR provide qualitative agreement with experimental results. Modest intensity lasers can be an excellent source for nanosecond bursts of soft X-rays.

The aneutronic 11B(p, α)2α fusion reaction driven by the interaction of high-energy lasers with matter has become a popular topic of research, since it represents a potential long-term goal alternative to the most studied deuterium-tritium reaction. However, the detection of the typical ionic products, especially alpha particles, of this low-rate fusion reaction is a challenging issue, due to their low flux. One of the diagnostic devices that can be implemented in laser-driven proton-boron fusion experiments is a Thomson spectrometer (TS), which is capable of detecting and discriminating ions according to their mass-to-charge ratio (A/Z, where A is the mass number and Z is the atomic number of the ions). In this work, we report on the ultimate test of a TS, which was designed and developed at the ENEA Research Centre in Frascati, Italy, in the context of a p + 11B fusion experiment. Our device—designed to have high sensitivity and a robust shielding against electromagnetic pulses (EMPs)—was implemented at the PALS laser facility (∼700 J in ∼350 ps pulses) at a distance of 367 mm from the laser-plasma interaction point. We analyse here the measured signals obtained with our device, focusing on the assessment of their signal-to-background ratio. Despite the presence of strong EMPs and background radiation at such a short distance from the laser-irradiated target, the TS proved to be suitable for effectively detecting protons and heavier ions stemming from the plasma source.

The characterization of energetic protons generated in the ShenGuang-II UP petawatt laser interactions with foil targets has been systematically studied. The proton energy spectra and angular distributions are measured with a radiochromic film stack. It shows that the proton energy spectra have a Boltzmann distribution with temperature of about 2.8 MeV and cutoff energy of about 20 MeV. The divergence angles of protons vary from 10° to 60°, dependent on the proton energy. The proton source size and location are investigated via the proton point-projection mesh imaging. The proton virtual sources are found to locate tens to hundreds of microns in front of the foil target, depending on the proton energies. A Monte Carlo simulation estimates the diameter of the virtual proton source to be about 12 μm for the protons with energy of 16.8 MeV, which is much smaller than the laser focus size of about 50 μm. The spatial resolution of the 16.8 MeV proton imaging is quantified with the point spread function to be about 15 μm, which is consistent with the proton virtual source size. These results will be important for the users conducting experiments with the protons as a backlighting source on the ShenGuang-II UP petawatt laser.

Relativistic surface high harmonics, combined with the use of polarization gating, present a promising route towards intense single attosecond pulses. However, they impose stringent requirements on ultra-high laser contrast and are restricted by large intensity losses in real experiments. Here, we numerically demonstrate that by setting an optimal time delay in the polarization gating scheme, the intensity of the generated single attosecond pulses can become approximately 100 times stronger than that with nonoptimal time delay in the coherent synchrotron emission process. When a petawatt-class driving laser irradiates a solid target, an ultra-dense electron nanobunch and a strong space-charge sheath develop, and the accumulated electrostatic energy is only released in half of the laser cycle when this electron nanobunch moves backward. This process results in the emission of intense high harmonics. Our study provides a reliable method for developing bright attosecond extreme ultraviolet pulses.

The energy balance of the p-11B fusion scenario with compensation of the transfer of kinetic energy of protons and alpha particles to the gas medium by the electric field is considered. It is shown that such scenario cannot provide the use of p-11B fusion reaction for power production due to the very low ratio of the energy release of the fusion reaction to the energy necessary for compensation. The upper boundary of this ratio is about $2\times {10}^{-3}$.

The advent of high-energy short-pulse laser beams poses new problems related to radiation protection. The radiation generated in experiments using multipetawatt laser systems leads to prompt doses and potentially to the activation of the materials within the interaction chamber and the experimental hall. Despite many new PW laser facilities are nowadays entering into operation, this question has received little attention until now. In this paper, we evaluate the radiological effects induced by the operation of a high-power laser facility. Two working regimes are considered related to the production of hard X-rays and energetic protons. The methodology is general and may be applied for the design of experiments with any high-power laser systems.

The laboratory generation and diagnosis of uniform near-critical-density (NCD) plasmas play critical roles in various studies and applications, such as fusion science, high energy density physics, astrophysics as well as relativistic electron beam generation. Here we successfully generated the quasistatic NCD plasma sample by heating a low-density tri-cellulose acetate (TCA) foam with the high-power-laser-driven hohlraum radiation. The temperature of the hohlraum is determined to be 20 eV by analyzing the spectra obtained with the transmission grating spectrometer. The single-order diffraction grating was employed to eliminate the high-order disturbance. The temperature of the heated foam is determined to be T = 16.8 ± 1.1 eV by analyzing the high-resolution spectra obtained with a flat-field grating spectrometer. The electron density of the heated foam is about $N_e=4.0\pm 0.3\times {10}^{20}{\text{cm}}^{-3}$ under the reasonable assumption of constant mass density.

The effects of magnetic vortex acceleration (MVA) are investigated with two-dimensional particle-in-cell (PIC) simulations by laser interaction with near-critical density (NCD) plasma inside a hollow conical plasma. Energetic and collimated proton beams can be accelerated by a longitudinal charge-separation field. Energetic protons with a peak energy of 220 MeV are produced in PIC simulations. Compared with a uniform NCD plasma, both the cutoff energy and collimation of proton beams are improved remarkably. Furthermore, the influence of different gap sizes of cone tip is taken into account. For optimizing magnetic vortex acceleration, the gap size of the cone tip is suggested to match the focal spot size of laser pulse.

Liquid leaf targets show promise as high repetition rate targets for laser-based ion acceleration using the Target Normal Sheath Acceleration (TNSA) mechanism and are currently under development. In this work, we discuss the effects of different ion species and investigate how they can be leveraged for use as a possible laser-driven neutron source. To aid in this research, we develop a surrogate model for liquid leaf target laser-ion acceleration experiments, based on artificial neural networks. The model is trained using data from Particle-In-Cell (PIC) simulations. The fast inference speed of our deep learning model allows us to optimize experimental parameters for maximum ion energy and laser-energy conversion efficiency. An analysis of parameter influence on our model output, using Sobol’ and PAWN indices, provides deeper insights into the laser-plasma system.

Terahertz (THz) radiation from a plasma cylinder with embedded radial electric and axial magnetic fields is investigated. The plasma density and the electric and magnetic fields are such that the electron plasma frequency is near the electron cyclotron frequency and in the THz regime. Two-dimensional particle-in-cell simulations show that the plasma electrons oscillate not only in the azimuthal direction but also in the radial direction. Spectral analysis shows that the resulting oscillating current pattern has a clearly defined characteristic frequency near the electron cyclotron frequency, suggesting resonance between the cyclotron and plasma oscillations. The resulting far-field THz radiation in the axial direction is also discussed.

The energy problem is an open issue becoming increasingly pressing. The possibility to use nuclear fusion as an alternative energy source is thus acquiring progressively more importance and many investors are pushing to achieve the goal of an electric plant based on fusion. The most studied reaction is the deuterium-tritium one, but this poses several technical issues related to the handling of the radioactive fuel and neutron generation. In this frame, the aneutronic 11B(p, α)2α fusion reaction has attracted the interest of many researchers. Despite a fusion reactor based on pB is still a long-term goal, the study of this reaction is important both for astrophysics research and for its possible employment in schemes of high brightness source of α particles for applications, as for instance in medicine. Nevertheless, the univocal identification of the produced alphas is a well-known challenging task when the reaction is triggered by high-intensity lasers. Indeed, due to the multifaceted emission typical of laser-matter interactions, the signal coming from alphas is often superimposed to that generated by protons and by other ions, and in many cases, it is therefore hardly recognizable. In this work, we analysed the possibility of employing a Thomson spectrometer (TS) with an adequate differential filtering system for the exclusion from the α-particle trace, the contribution of all other ionic species. Moreover, for the energy ranges where the filtering method cannot be successfully applied, we investigated the feasibility of integrating in the TS assembly a particle detector for time-of-flight (TOF) measurements.

Stimulated Raman forward scattering (SRFS) of an intense X-mode laser pump in a preformed parabolic plasma density profile is investigated. The laser pump excites a plasma wave and one/two electromagnetic sideband waves. In Raman forward scattering, the growth rate of the parametric instability scales as two-third powers of the pump amplitude and increases linearly with cyclotron frequency.

Two-dimensional electromagnetic particle-in-cell simulations are carried out to investigate the effect of ion-to-electron mass ratio on the evolution of warm electron beam-plasma instability. Four cases are considered: A: mi/me = 0 (two-electron stream instability); B: mi/me = 1 (pair plasma); C: mi/me = 100; and D: mi/me = 1000. It is shown that the generation of Langmuir waves in the fundamental mode of electron plasma frequency and the subsequent dynamics of large-amplitude solitons are not affected by the ion species. However, it determines the decay process of solitons and the excitation of electromagnetic waves in the second harmonic. In the first two cases, mi/me = 0 and 1, there is no sign of emission in the second harmonic, while the strongest emission in the second harmonic is found for the case of largest mass ratio, mi/me = 1000. This confirms the two-step wave-wave coupling mechanism for the generation of second harmonic electromagnetic waves, which requires the excitation of ion-acoustic waves in the first step. Moreover, the dispersion diagrams of all excited waves are presented.

The third-order nonlinear optical properties of three hydrazone derivatives, namely, ethyl 2-((2E)-2-(4-(dimethylamino)benzylidene]hydrazinyl)-5-nitrobenzoate, ethyl 2-((2E)-2-(4-chlorobenzylidene)hydrazino)-5-nitrobenzoate, and methyl 5-nitro-2-((2E)-2-(4-nitrobenzylidene)hydrazino)benzoate were investigated by the single beam Z-scan technique with nanosecond laser pulses at 532 nm. The compounds were doped into PMMA (poly (methyl methacrylate)), and their third-order nonlinearity was studied with a prospective of reaching a compromise between processability and high nonlinear optical behavior. The optical limiting study of the samples was carried out at 532 nm. The measured values of the third-order nonlinear susceptibility, χ(3), and the nonlinear refractive index, n2, are of the order of 10−13 esu and 10−11 esu, respectively. The nonlinear absorption in materials was attributed to reverse saturable absorption. The results are quite promising for possible applications in photonic devices.

A comparative analysis of a fast atom beam and ion beam effect on a metal target in the binary collision model is performed. Irradiation by fast atoms has been shown to more closely correspond to neutron radiation in a nuclear reactor, in terms of the primary knocked-on atom spectrum and the efficiency and mechanism of the radiation defect formation. It was found that upon irradiation by fast carbon atoms with an energy of 0.2-0.3 MeV, the average number of radiation defects in the displacement cascade of one atom is four to five times higher than the calculated values using the SRIM program for ions with the same energy. It is shown that during penetration in the target, the probability of ionization of atoms with energies less than 0.4 MeV is negligible.

L subshell X-rays of 48Cd and 49In have been measured for the impact of protons with energies from 75 to 250 keV. Obviously, it is found that Lγ2 (abbreviation Lγ2,3 for 48Cd and Lγ2,3,4 for 49In) X-ray emission is enhanced in comparison with Lγ1 X-ray emission. The relative intensity ratios of Lγ2 to Lγ1 X-ray are larger than the atomic data and increase with decreasing proton energy. This is caused by the multiple ionization of outer-shell electrons. To verify this explanation, the enhancements for relative intensity ratio of Lι and Lβ2 to Lα X-ray in experiments are discussed, and the direct ionization cross sections of 4d, 5s, and 5p electrons are calculated using BEA theory.