The state of river channels and their riparian zones in terms of geomorphology and vegetation has a significant effect on water and sediment transport in headwater catchments. High roughness in natural rivers due to vegetation and geomorphological attributes generate drag on flowing water. This drag will slow water discharge, which in turn influences the sediment dynamics of the flow. The impacts of changes in the management of rivers and their riparian zone (either by catchment managers or river restoration plans) impacts both up- as well as downstream reaches, and should be assessed holistically prior to the implementation of these plans.

To assess the river's current state as well as any possible changes in geomorphology and vegetation in and around the river, effective approaches to characterise the river are needed. In this paper, we present a practical approach for making detailed surveys of relevant river attributes. This methodology has the benefit of being both detailed – describing river depth, width, channel morphology, erosive features and vegetation types – but also being practical in terms of time management. This is accomplished by identifying and describing characteristic benchmark reaches (typical sites) in detail against which the remainder of the river course can be rated. Using this method, a large river stretch can be assessed in a relatively short period while still retrieving high quality data for the total river course. In this way, models with high data requirements for assessing the condition of a river course, can be parameterised without major investments on field surveys.

In a small headwater catchment (23 km2) in southwestern Poland, this field methodology was used to retrieve data to run an existing model (HEC-GeoRAS) which can assess the impact of changes in the riparian and channel vegetation and channel management on sedimentation processes and stream flow velocity. This model determines the impact of channel morphology and in-channel and riparian vegetation on stream flow and sediment transport. Using four return periods of flooding (2, 10, 20 and 100 years), two opposing channel management / morphology scenarios were run; a natural channel and a fully regulated channel. The modelling results show an increase in the effect of riparian vegetation / geomorphology with an increase in return period of the modeled peak discharge. More natural channel form and increased roughness reduces the stream flow velocity due to increasing drag from flow obstructions (vegetation and channel morphological features). The higher the flood water stage, the greater the drag due to vegetation on the floodplains of natural river reaches compared to channelised sections. Slower flow rates have an impact on sediment mobilisation and transport in the river.

The knowledge of the Eemian fauna of central Europe is based on the fossil record from a number of sites located in the eastern part of Germany. The faunas with different deer species as well as Sus scrofa, Palaeoloxodon antiquus, Stephanorhinus kirchbergensis and Glis glis indicate a forested environment alternating during the climatic optimum of the Eemian s.s. with areas with a more open environment inhabited by species such as Cricetus cricetus, Equus sp. (or Equus taubachensis), Equus hydruntinus and Stephanorhinus hemitoechus. Characteristic for the Rhine valley fauna are Hippopotamus amphibius and the water buffalo (Bubalus murrensis); both species are absent in the eastern German faunas with an Eemian age.

Taking into account the short period of time covered by the Eemian s.s., the amount of data on the Eemian mammalian fauna is remarkably large. There is, however, still an ongoing debate on whether the stratigraphical position of a number of faunas are of Eemian or ‘intra-Saalian’ age. Furthermore, there are faunal assemblages or stratigraphically isolated finds referred to the Eemian without indisputable evidence. This is particularly the case in the Rhine valley, where most of the so-called Eemian fossils come from dredged assemblages. The picture of the evolution of the Eemian fauna and its geographical variation is consequently still incomplete.

The Amsterdam glacial basin was a major sedimentary sink from late Saalian until late Eemian (Picea zone, E6) times. The basin’s exemplary record makes it a potential reference area for the last interglacial stage. The cored Amsterdam-Terminal borehole was drilled in 1997 to provide a record throughout the Eemian interglacial. Integrated facies analysis has resulted in a detailed reconstruction of the sedimentary history.

After the Saalian ice mass had disappeared from the area, a large, deep lake had come into being, fed by the Rhine river. At the end of the glacial, the lake became smaller because it was cut off from the river-water supply, and eventually only a number of shallow pools remained in the Amsterdam basin. During the early Eemian (Betula zone, El), a seepage lake existed at the site. The lake deepened under the influence of a steadily rising sea level and finally evolved into a silled lagoon (late Quercus zone, E3). Initially, the lagoon water had fairly stable stratification, but as the sea level continued to rise the sill lost its significance, the lagoon becoming well mixed by the middle of the Corylus/Taxus zone (E4b). The phase of free exchange with the open sea ended in the early Carpinus zone (E5), when barriers developed in the sill area causing the lagoon to become stratified again. During the Late Eemian (late E5), a more dynamic system developed. The sandy barriers that had obstructed exchange with the open sea were no longer effective, and a tidally-influenced coastal lagoon formed.

The Eemian sedimentary history shown in the Amsterdam-Terminal borehole is intimately connected with the sea-level history. Because the site includes both a high-resolution pollen signal and a record of sea-level change, it has potential for correlation on various scales. Palaeomagnetic results show that the sediments predate the Blake Event, which confirms that this reversal excursion is relatively young. The U/Th age of the uppermost part of the Eemian sequence is 118.2±6.3 ka.

For more than one century, the textural B-horizon of the last interglacial soil and its cover deposits have been standing out in Europe as an important pedostratigraphic marker. The complexity of this horizon was well illustrated since the seventies, though its pedological and stratigraphic significance remained doubtful. Macro-, meso- and micromorphological data gathered by the authors at various key-sites in Europe and the sequential correlation principle have resulted in a better understanding of the high complexity of the pedosedimentary and stratigraphical evolution of the last interglacial and early glacial loess succession. The present study identifies four megacyclic pedosedimentary intervals that show a general trend towards dry and continental climatic conditions.

A consistent correlation exists between pedosedimentary evolution and vegetation, as recorded in the Grande Pile pollen record. The picture obtained in the present study is similar for both the Western and the Eastern European loess palaeosol successions. The so-called ‘last interglacial soil’, with three major soil-forming processes, belongs to the Eemian and Saint-Germain I (MIS substages 5e and 5c), whereas the humiferous sediments and soils on top are linked to Melisey II, Saint-Germain II and Ognon I (MIS substages 5b and 5a).The overlying loess, colluvial sediments and humiferous soils that end the palaeosol succession belong to the Ognon II and III interstadials; they record the onset of the early Pleniglacial (MIS stage 4) characterized by a significant increase in aeolian sedimentation.

After more than half a century of production and with some 350 wells, the Groningen gas field must be one of the best-studied gas fields in the world. Initially, it was considered to be relatively simple and behaving like one big tank. Now that it is entering a phase of declining production it has become clear that many subtleties are not fully understood yet. Prediction and management of subsidence and induced earth tremors require a detailed understanding of the field geology. In addition, an optimum gas recovery is only possible if details of, for example, reservoir quality distribution and faulting, that did not appear relevant before, are well understood.

The large Groningen field comprises a structurally high block during much of its history, probably already from Devonian times onwards. The desert sandstones of the Rotliegend reservoir exhibit a strong south-to-north proximal–distal relationship. Whilst diagenesis has in many fields led to deterioration of reservoir properties, this effect is small in the Groningen field. The field is dipping to the north, and bounded by a series of normal faults in the west, south and east. Almost all faults are normal extensional faults, but locally inverse reactivation has led to small pop-up structures. Reactivation of older faults must have resulted in oblique movements along most faults.

The challenges for future development of the Groningen field are immense. Managing the risks associated with induced seismicity and recovery of the remaining gas will continue to require an increasingly detailed knowledge and understanding of its geology.

Uplift of the Rhenish Massif can be demonstrated by means of the stream-made river terrace system that accompanies the Rhine river and its tributaries along their way through or within this part of the Variscan fold and thrust belt. The height difference between a former valley floor, especially that of the Younger ‘Hauptterrasse’ (Main Terrace), and the recent one allows to quantify the uplift by the amount of downcutting erosion. The uplift velocity increased just after the BRUNHES / MATUYAMA boundary, i.e. about 0.8 Ma B.R Since that time, a domal uplift of more than 250 m is documented in the eastern Hunsriick and in the south-eastern Eifel. The area of this maximum height anomaly is situated just between the East-and West-Eifel Quaternary volcanic districts. Thus, causal connections are supposed. The domai uplift is affected by normal faulting partly inherited since Tertiary rifting.

The Late Cretaceous and Cenozoic sedimentary record in the Campine Basin along the southern border of the North Sea Basin is analysed in terms of sequence stratigraphy. All available biostratigraphic, and in some cases, magnetostratigraphic data are used to constrain the sequence chronostratigraphy. The relative geographic extent of the strata is used as an indication of the relative sea level. Tectonic and eustatic components could be distinguished in several cases using regional geological information. Generally, sequences consist of transgressive and highstand systems tracts only and have flat, abrasion-type lower boundaries. Lowstand deposits are only identified as infill of erosional space, which generally implies marked tectonic uplift. Several eustatic and tectonic events can be correlated with similar events known elsewhere in the North Sea Basin. The time intervals spanned by the different sequences vary considerably, pointing out different control mechanisms.

Three durophagous mosasaur species are represented by isolated teeth in the Upper Cretaceous (Maastrichtian) phosphatic beds of Morocco. Globidens phosphaticus nov. sp. is characterised mainly by a strong heterodonty, with mid-posterior teeth being bulbous, irregularly oval in crosssection, and having an inflated posterior surface, a large eccentric located and recurved apical nubbin, vertical sulci on medial and lateral faces, no carinae and an enamel surface covered by anastomosing ridges. Teeth of Prognathodon currii are broad and tall, straight cones, slightly swollen at the base, and with two serrated carinae. These two taxa have been collected from all the phosphatic series (lower to upper Maastrichtian) in the Ganntour Basin (Morocco). Globidens phosphaticus nov. sp. is probably also represented at other Maastrichtian phosphatic sites along the southern margin of the Mediterranean Tethys. Prognathodon currii was previously known only from the Upper Cretaceous phosphates of Negev. Of the third taxon, Carinodens belgicus, only a single tooth (now lost) is known from the Oulad Abdoun Basin (Morocco); this is low, swollen, laterally compressed and bicarinate with a large apical nubbin. Previous records of this species include Europe and Brazil.

A general model is presented for the small type of fans (not to be confused with sandurs) that develop subaerially in the zone immediately before an ice front. These fans have in common with other fans that a proximal, a middle and a distal subenvironment– with distinctly different sedimentary facies– can be distinguished. The characteristics of these fans differ in several respects, however, from those formed under other conditions, particularly by the high proportion of mass-flow deposits in the proximal part, by the relative scarcity of fine particles in the middle fan, and by the relatively uniform character of the sediments in the distal fan.

The special character of this type of fan is ascribed to the interaction of a continuously changing distance between the ice front and the fan (as a result of alternating phases of ice advance and ice retreat), its position that may be surrounded by ice for a large part, and the irregular supply of debris-laden meltwater that comes sometimes even in the form of more or less catastrophic floods.

Due to the fact that terminoglacial fans have a good preservation potential only during phases of ice retreat, these fas tend to show a slight fining-upward tendency. The slope of terminoglacial fans tends to be more gentle (rarely over 2–5°) than that of fans formed under different conditions.

In order to obtain a better understanding of the infilling of the Saalian glacial basins during the Eemian, particularly following the recent research in the Amsterdam Basin (Terminal borehole), it was necessary to re-investigate the type locality of the Eemian at Amersfoort. Both published and unpublished data from various biota (diatoms, foraminifers, molluscs, ostracods, pollen) provide new information on the changing sedimentary environments during the Eemian. Although the organic and clastic sediments of the infilling represent nearly all the pollen zones, the sedimentary sequence at Amersfoort is discontinuous: four breaks at least are recognised at the type locality.

The successive sedimentary environments and the breaks in the record are linked with the transgression of the Eemian sea, the topographic position at the margin of an ice-pushed ridge, and the changes in hydrodynamic conditions. Local conditions, such as a sandy sea bed, shallow water and a reduced water exchange near the North Sea margin, influenced the salinity of the basin. Rib counts of Cerastoderma edule shells indicate a higher salinity at the end of the Taxus (E4b) and the beginning of the Carpinus (E5) zones than that present in the modern North Sea. Local conditions were responsible for the higher salinity following the climate optimum.

During the Abies phase (the later part of regional pollen zone E5), the sea level had already fallen. The change from eu-trophic peat growth (with Alnus and Salix) to an oligotrophic Ericaceae/Sphagnum community at the end of the Eemian resulted from the change from a marine to a fresh-water environment, probably coherent with a deterioration of the climate.

This paper discusses the faunal content, the mammal biostratigraphy, and the environmental ecology of three important continental Tertiary vertebrate faunas from the Lower Rhine Embayment. The sites investigated are Rott (MP 30, Late Oligocene), Hambach 6C (MN 5, Middle Miocene), Frechen and Hambach 11 (both MN 16, Late Pliocene). Comparative analysis of the entire faunas shows the assemblages to exhibit many conformities in their general composition, presumably resulting from their preference for wet lowlands. It appears that very similar environmental conditions for vertebrates reoccurred during at least 20 Ma although the sites are located in a tectonically active region with high subsidence rates. Differences in the faunal composition are partly due to local differences in the depositional environment of the sites: lake deposits at the margin of the embayment (Rott), coal swamp and estuarine conditions in the centre of the embayment (Hambach 6C), and flood plain environments with small rivulets (Frechen and Hambach 11). The composition of the faunal assemblages (diversity and taxonomy) also documents faunal turnovers with extinctions and immigrations (Oligocene/Miocene and postMiddle Miocene), as a result of changing climate conditions.

Additional vertebrate faunal data were retrieved from two new assemblages collected from younger strata at the Hambach mine (Hambach 11C and 14). They are important for the understanding of the Plio-Pleistocene transition in the southern part of the Lower Rhine Embayment and for correlating depositional sequences in the Dutch/German borderland.

New elasmosaurid plesiosaur specimens are described from the Early Maastrichtian of Angola. Phylogenetic analyses reconstruct the Angolan taxon as an aristonectine elasmosaurid and the sister taxon of an unnamed form of similar age from New Zealand. Comparisons also indicate a close relationship with an unnamed form previously described from Patagonia. All of these specimens exhibit an ostensibly osteologically immature external morphology, but histological analysis of the Angolan material suggests an adult with paedomorphic traits. By extension, the similarity of the Angolan, New Zealand and Patagonian material indicates that these specimens represent a widespread paedomorphic yet unnamed taxon.

Neotectonic movements have caused differential subsidence in the Lower Rhine Embayment during the Quaternary. The Late Weichselian and Holocene Rhine-Meuse fluvial archive in the central Netherlands was used to quantify neotectonic movements in a setting that was primarily controlled by sea-level rise and climate change. Evidence for neotectonic activity in the central Netherlands is reviewed. Sedimentary evidence shows that fluvial deposits of Late Weichselian and Holocene Rhine and Meuse (Maas) distributaries are vertically displaced along the northern shoulder of the Roer Valley Graben system. Elevation differences in the longitudinal profiles of Late Weichselian terrace deposits were used to quantify tectonic displacements. New results for the southeastern Rhine-Meuse delta (Maaskant area) show that displacements in the top of the Pleniglacial terrace along the Peel Boundary Fault are up to 1.4 m. The maximum displacement between the Peel Horst and the Roer Valley Graben is 2.3 m. This is equivalent to relative tectonic movement rates of 0.09-0.15 mm/yr, averaged over the last 15,000 years.

The hydrocarbon systems of the Mesozoic, inverted West Netherlands Basin have been analyzed using 2-D forward modelling. Three source rocks are considered in the modelling: Lower Jurassic oil-prone shales, Westphalian gas-prone coal deposits, and Lower Namurian oil-prone shales. The Lower Namurian hydrocarbon system of the basin is discussed for the first time.

According to the modelling results of the Early Jurassic oil system, the oil accumulations were filled just after the main inversion event. Their predicted locations are in agreement with exploration results. Modelling results of the Westphalian gas system, however, show smaller and larger sized accumulations at unexplored locations. The gas reservoirs were filled during the Late Jurassic-Early Cretaceous rifting phase. Results of modelling of the Lower Namurian oil system indicate that gas formed by secondary cracking of the oils can have mixed with the Westphalian coal-derived gas. Such a mixing is inferred from geochemical analyses. The existence of a Lower Namurian hydrocarbon system in the West Netherlands Basin implies that hydrocarbons are possibly trapped in the Westphalian and Namurian successions. These potential traps in the basin have not yet been explored.

A revised Upper Cenozoic stratigraphic framework of the Dutch sector of the North Sea Basin is presented whereby offshore stratigraphic units are integrated or correlated with onshore units. The framework is based on an integrated stratigraphic approach that combines elements of lithostratigraphy, seismostratigraphy and allostratigraphy. Offshore formations are redefined in terms of seismofacies and lithofacies associations, and are differentiated on the basis of common genesis and stratigraphic position. These facies associations represent five major depositional environments, which occur in repetitive successions in the subsurface of the Netherlands: Marine, Coastal, Glacial, Fluvial, and Local Terrestrial. Five conceptual basin-wide bounding discontinuities are identified in the North Sea-Basin that span land and sea. They are represented by both seismostratigraphic and lithostratigraphic unconformities and interpreted as surfaces that formed as a result of North Sea Basin-wide changes in depositional systems. Their formation relates to sea level rise, continental-scale glaciations, and tectonic processes. The bounding discontinuities separate informal allostratigraphic groups of formations that have a grossly uniform geologic setting in common. While the allostratigraphic principles provide a view on the stratigraphy on the largest spatial and temporal scale, the genetic concept facilitates mapping on a local scale.

The River Rhine and its tributaries represent one of the largest drainage systems in Europe. Its prominence among other fluvial systems is due to the location of its headwaters within the central Swiss Alps, which were repeatedly glaciated during the Quaternary, and the concurrence of major parts of the River Rhine course with the European Cenozoic Rift System. Sediments of the Rhine have thus recorded both changes in climate and tectonic activity as well as sea level change in the lower part of the river course.

The River Rhine is composed of different subdivisions characterised by distinct geographical and geological settings. Vorder-and Hinterrhein in the headwaters are inner-alpine rivers frequently influenced in their course by tectonic lines and the blockage of valley floors by the deposits of mass movements. The Alpenrhein is located in a main Alpine valley that drains into a large foreland basin, the Bodensee (Lake Constance). The Hochrhein flows out of the lake following the Jura Mountains in a western direction. All these areas display a series of geological features such as moraine ridges and outwash plains, which directly reflect Quaternary glaciations of the Alps. The Oberrhein (Upper Rhine) Valley, as a graben structure, is part of the rifting system that started to develop during the middle Tertiary. The northern end of the graben is represented by the triple junction of the Mainz Basin, which is mainly characterised by the remains of marine transgressions that occurred during the initial rifting phase. The Rhine continues following the western branch of the tectonic system by passing through the Rhenish Massif. Uplift in this so-called Mittelrhein (Middle Rhine) area is well documented by a flight of late Tertiary to Quaternary river terraces. This region is also characterised by young volcanic activity as found, for example, in the Eifel volcanic field. The Niederheinische Bucht (Lower Rhine Embayment), especially the Roer Valley Rift System, represents the northern continuation of the rifting system. This area is characterised by differential uplift in the southern and subsidence in the northern part of the basin, which continues into the Netherlands. Here, the main stream of the River Rhine is separated into different branches developing an active delta at the coast of the North Sea. When the North Sea Basin was covered by ice during the Elsterian, Saalian and probably also the Weichselian glaciation and global sea level was low, the Rhine continued its course through the English Channel and flowed into the North Atlantic off Brittany.

At river bifurcations water and sediment is divided among the downstreambranches. Prediction of the sediment transport rate and division thereof atbifurcations is of utmost importance for understanding the evolution of thebifurcates for short-term management purposes and for long-term fluvialplain development. However, measured sediment transports in rivers rarelyshow a uniquely determined relation with hydrodynamic parameters. Commonly ahysteresis is observed of transport rate as a function of discharge or shearstress which cannot be explained with the standard sediment transportpredictor approach. The aim of this paper is to investigate the causes ofhysteresis at a bifurcation of the lower Rhine river, a meandering riverwith stable banks, large dunes during flood, and poorly sorted bed sediment.The hydrodynamics and bed sediment transport were measured in detail duringa discharge wave with a recurrence interval larger than 10 years.Surprisingly, the hysteresis in bedload against discharge was in theopposite direction upstream and downstream of the bifurcation. The upstreamclockwise hysteresis is caused by the lagging development of dunes duringthe flood. The counter-clockwise hysteresis downstream of the bifurcation iscaused by a combination of processes in addition to dune lagging, namely 1)formation of a scour zone upstream of the bifurcation, causing a migratingfine sediment wave, and 2) vertical bed sorting of the bed sediment by duneswith avalanching lee-sides, together leading to surface-sediment fining andincreased transport during and after the flood. These findings lead tochallenges for future morphological models, particularly for bifurcations,which will have to deal with varying discharge, sediment sorting in thechannel bed, lagging dunes and related hydraulic roughness.

The Late Permian Zechstein carbonates in the Southern Permian Basin were deposited under marine conditions. The carbonates form part of a largely progradational infill, with a gradual northward facies shift. The paleogeography of the Zechstein carbonate deposits has been reviewed recently on the base of well data, cores and publications. This has resulted in three updated maps of the carbonate units. These maps reflect the increase in knowledge of the palaeogeography of the Zechstein as a result of several decades of subsurface exploration. It is found that deposition of the carbonates was controlled by various factors, i.e., rifting during deposition of the basal Zechstein, sea-level fluctuations and basin subsidence. This resulted in an overall E-W orientated facies distribution in the Zechstein carbonates, and in the gradual northward shift of the various facies belts in time.

Reefs in the Zl Carbonate Member and off-platform highs and turbidites in the Z2 Carbonate Member have been identified as potential future exploration targets.

A seismic velocity model is necessary to map depth and thickness of subsurface layers interpreted from seismic reflection images. We have built a seismic velocity model (VELMOD-1) for the entire Netherlands area, both onshore and offshore, using non-confidential data (sonic logs, time-depth pairs, lithostratigraphic marker depths and downhole position data) of 720 boreholes in DINO - National Geoscientific Portal, and a preliminary isochore map (in seismic traveltime representation) of the layer of the Zechstein Group. The model is based on the Vint-zmid method applied to the following lithostratigraphic layers: Lower, Middle and Upper North Sea groups; Chalk Group; Rijnland Group; Schieland, Scruff and Niedersachsen groups; Altena Group; Lower and Upper Germanic Trias groups; Upper Rotliegend Group; and Limburg Group. Per layer, the linear least squares approximation, applied to Vint as a function of zmid, provides parameters V0 and K for a linear velocity function V(z) = V0 + K · z. In VELMOD-1, K is constant, at least at the scale of structural elements, whereas V0 varies with location. At borehole locations, V0 is calibrated such that traveltime through the layer according to the linear velocity model equals the traveltime according to the borehole data. A kriging procedure is applied to the calibrated V0(x, y)-values resulting in an estimated V0-value at any other location. The model V0-values were determined on an areal grid with cells of 1 km × 1 km. On the same grid, kriged interval velocities constitute the model for the Zechstein Group. These interval velocities stem directly from interval velocities at borehole locations; at other positions they are also dependent on the thickness (in terms of seismic traveltime isochores) of the layer of the Zechstein Group. Maps are presented of the distributions of both V0 and its standard deviation for two layers: that of the Chalk Group and that of the Lower and Upper Germanic Trias groups.

The fluvial history of the northern Lower Rhine Embayment shows interplay of three main river systems: Rhine, Meuse and smaller rivers draining the central and northern part of Belgium.

The Pliocene and Early Pleistocene (pre-)Rhine and Meuse river systems had their conjunction in the southern part of the Roer Valley Graben between Aachen and Jülich. Despite slight differences in the heavy-mineral assemblages the lithological composition of the Pliocene deposits of the three river systems shows close resemblance and therefore they cannot be mapped separately. However, due to a marked change of the petrographical composition the Upper Pliocene and Lower Pleistocene deposits of the Rhine are easily recognised and as a result Rhine and Meuse deposits can be mapped separately upstream of their confluence.

The Lower Pleistocene deposits of Rhine, Meuse and the Belgian rivers show a clear interrelationship. They are bounded by two regional well-mapable unconformities and are preserved in from west to east changing lithostratigraphical sequences. Revision of the lithostratigraphical schemes in Germany and the Netherlands and the better defined lithostratigraphical position of Meuse deposits in Germany now strongly constrain the correlation of the various fluvial deposits. As a result existing reconstructions of the fluvial deposition and tectonic history of the southern Roer Valley Graben can be evaluated and re-adjusted.

It is concluded that the main course of the Meuse was aligned through the so-called East Meuse valley during the larger part of the Early Pleistocene. Available pollen data do not conflict with this conclusion. At the same time the Rhine ceased to enter the southern part of the Roer Valley Graben. Instead, the Meuse accumulated here a series of deposits derived from the East-Meuse valley. Simultaneously, the Belgian rivers filled available accommodation space in the Roer Valley Graben of the southern Netherlands. The conclusions are based primarily on the revised lithostratigraphical framework. In general they simplify the picture of fluvial and tectonic behaviour of the area.