Propulsion systems have revolutionised human activities and made the world smaller. They have brought transport advances that enabled the conversion of dreams into reality. Very large international high-technology investments are being made to continue to develop efficient and affordable gas turbine and ramjet propulsion while implementing knowledge that is bringing large environmental benefits.

This paper presents performance analyses of the model-scale ERICA and TILTAERO tiltrotors and of the full-scale XV-15 rotor with high-fidelity computational fluids dynamics. For the ERICA tiltrotor, the overall effect of the blades on the fuselage was well captured, as demonstrated by analysing surface pressure measurements. However, there was no available experimental data for the blade aerodynamic loads. A comparison of computed rotor loads with experiments was instead possible for the XV-15 rotor, where CFD results predicted the FoM within 1.05%. The method was also able to capture the differences in performance between hover and propeller modes. Good agreement was also found for the TILTAERO loads. The overall agreement with the experimental data and theory for the considered cases demonstrates the capability of the present CFD method to accurately predict tiltrotor flows. In a second part of this work, the validated method is used for blade shape optimisation.

Various liquid and gaseous alternative fuels have been proposed to replace the kerosene as aircraft fuel. Furthermore, new combustion technologies were developed to reduce the emissions of aero-engine. A staged fuel injection arrangement for a lean burn combustion system was applied to improve the operability of an aero-engine by achieving high flame stability at reduced combustion emissions. Originally, both circuits (pilot and main) are fuelled by kerosene; moreover, the pilot injector is operating at low power (engine idle and approach) and the pilot flame is anchored in an airflow recirculation zone. In the case of the performed research, the pilot injector was modified to allow the use of gaseous fuels. Thus, the burner model allows a flexible balancing of the mass flows for gaseous and liquid fuel. The present paper describes the investigation of ignitability for the proposed staged combustor model fuelled by gaseous and liquid fuels. A short overview on physical properties of used fuels is given. To investigate atomisation and ignition, different measurements systems were used. The effectiveness of two ignitor types (spark plug and laser ignitor) was analysed. The ignition performance of the combustor operating on various fuels was compared and discussed in detail.

In this paper, structural modelling and dynamic analysis methods reflecting the characteristics of a liquid propellant were developed for a pogo analysis. The pogo phenomenon results from the complex interaction between the vehicle structural vibration in the longitudinal direction and the propulsion system. Thus, for an accurate vibration analysis of a liquid propellant launch vehicle, both the consumption of the liquid propellant and the change in the stiffness reflecting the nonlinear hydroelastic effect were simultaneously considered. A complete vehicle structure, including the liquid propellant tanks, was analytically modelled while focusing on pogo. In addition, a feasible liquid propellant tank modelling method was established to obtain an one-dimensional complete vehicle model. With these methods, comparative studies of the hydroelastic effect were conducted. Evaluations of the dynamic analysis of a reference vehicle were also conducted during the first burning stage. The numerical results obtained with the present orthotropic model and the dynamic analysis method were found to be in good agreement with the natural vibration characteristics according to previous analyses and experiments. Additionally, the reference vehicle showed the estimated occurrence of pogo in the first structural mode when compared with the frequencies of the propellant feeding system. In conclusion, the present structural modelling and modal analysis procedures can be effectively used to analyse dynamic characteristics of liquid propellant launch vehicles. These techniques are also capable of identifying the occurrence of pogo and providing design criteria related to pogo instability.

Some helicopter manufacturers are exploring the compound helicopter design as it could potentially satisfy the new emerging requirements placed on the next generation of rotorcraft. It is well understood that the main benefit of the compound helicopter is its ability to reach speeds that significantly surpass the conventional helicopter. However, it is possible that the introduction of compounding may lead to a vehicle with significantly different flight characteristics when compared to a conventional helicopter. One method to examine the flight dynamics of an aircraft is to create a linearised mathematical model of the aircraft and to investigate the stability derivatives of the vehicle. The aim of this paper is to examine the stability derivatives of a compound helicopter through a comparison with a conventional helicopter. By taking this approach, some stability, handling qualities and design issues associated with the compound helicopter can be identified. The paper features a conventional helicopter and a compound helicopter. The conventional helicopter is a standard design, featuring a main rotor and a tail-rotor. The compound helicopter configuration features both lift and thrust compounding. The wing offloads the main rotor at high speeds, whereas two propellers provide additional propulsive thrust as well as yaw control. The results highlight that the bare airframe compound helicopter would require a larger tailplane surface to ensure acceptable longitudinal handling qualities in forward flight. In addition, without increasing the size of the bare airframe compound helicopter’s vertical fin, the Dutch roll mode satisfies the ADS-33 level 1 handling qualities category for the majority of the flight envelope.

This paper considers capabilities and benefits of aircraft-sized radio/radar frequency anechoic chambers for Test and Evaluation (T&E) of Electronic Warfare (EW), radar and other electromagnetics aspects of air and ground platforms. There are few such chambers worldwide. Initially developed to reduce costs, timescales and risks associated with open-air range flight testing of EW systems, their utility has expanded to most areas of platforms’ electromagnetics’ T&E. A key feature is the ability to conduct T&E of nationally sensitive equipment and systems, fully installed on platforms, in absolute privacy. Chambers’ capabilities and uses are described, with emphasis on key infrastructure and instrumentation. Non-EW uses are identified and selected topics elaborated. Operation and maintenance are discussed, based on experiential knowledge from international use and the authors’ 30 years’ involvement with BAE Systems’ EW Test Facility. A view is provided of trends and challenges whose resolution could further increase chamber utility. National affordability challenges also suggest utility expansion to support continuing moves, from expensive and difficult to repeat flight test and operational evaluation trials, towards an affordability-driven optimal balance between modelling and simulation, and real-world testing of platforms.

Variable tail rotor speed is investigated as a method for reducing tail rotor power, and improving helicopter performance. A helicopter model able to predict the main rotor and tail rotor powers is presented, and the flight test data of the UH-60A helicopter is used for validation. The predictions of the main and tail rotor powers are generally in good agreement with flight tests, which justifies the use of the present method in analysing main and tail rotors. Reducing the main rotor speed can result in lower main rotor power at certain flight conditions. However, it increases the main rotor torque and the corresponding required tail rotor thrust to trim, which then decreases the yaw control margin of the tail rotor. In hover, the tail rotor may not be able to provide enough thrust to counter the main rotor torque, if it is slowed to follow the main rotor speed. The main rotor speed corresponding to the minimum main rotor power increases, if the change of tail rotor power in hover is considered. As a helicopter translates to cruise, the induced power decreases, and the profile power increases, with the profile power dominating the tail rotor. Reducing the tail rotor speed in cruise reduces the profile power to give a 37% reduction in total tail rotor power and a 1.4% reduction to total helicopter power. In high-speed flight, varying the tail rotor speed is ineffective for power reduction. The power reduction obtained by the variable tail rotor speed is reduced for increased helicopter weight.

Aviation brings great commercial and social benefits and, as the global economy develops, the demand for air transport is expected to grow. However, aviation also contributes to climate change and there is increasing international pressure to limit mean global temperature rise. Therefore, the future success of aviation is likely to depend upon the industry's ability to hold its environmental impact within politically acceptable limits. This paper describes aviation's interaction with climate and sets out, in broad terms, the challenge facing the industry. The prospects for mitigating the adverse effects by advanced technology working through aircraft design and manufacture are assessed and some potential restrictions imposed by airport infrastructure are identified. Some consideration is also given to the practicalities imposed by airline economics and the likely impact of the recent ICAO regulations, plus the proposed global-based market measures scheme for aviation carbon offset. It is argued that the environmental problem is not just about carbon dioxide emissions and that aircraft technology improvement alone is unlikely to provide a complete solution. The observation that, in current operations, the total fuel used is almost twice the minimum required suggests a need to recognise a broader ownership of the problem and broader responsibility for the solution. However, improvements in the overall system efficiency will probably need to be driven by additional regulation and the imposition of other financial measures.

The overall conclusion is that the actions currently being taken and currently being proposed are probably not sufficient in themselves to meet the challenge of climate change. However, it appears that there is more that can be done and, provided that action is taken soon, there are some grounds for optimism that aviation will still be able to meet the needs of society in the 21st century.

The historical trends of reduction in fuel consumption and emissions from aero engines have been mainly due to the improvement in the thermal efficiency, propulsive efficiency and combustion technology. The engine Overall Pressure Ratio (OPR) and Turbine Inlet Temperature (TIT) are being increased in the pursuit of increasing the engine thermal efficiency. However, this has an adverse effect on engine NOx emission. The current paper investigates a possible solution to overcome this problem for future generation Very High Bypass Ratio (VHBR)/Ultra High Bypass Ratio (UHBR) aero-engines in the form of an Inter-stage Turbine Burner (ITB). The ITB concept is investigated on a next generation baseline VHBR aero engine to evaluate its effect on the engine performance and emission characteristics for different ITB energy fractions. It is found that the ITB can reduce the bleed air required for cooling the HPT substantially (around 80%) and also reduce the NOx emission significantly (>30%) without penalising the engine specific fuel consumption.

The rapid increase in the demand for air transportation over the last four decades has led to serious capacity problems for both the airside and landside components of major airports. The efficient management of existing airside resources seems to be the most effective and practical approach to overcome these capacity and traffic flow problems. Although integrated management of aircraft parking position assignments and ground movement planning processes are vital for the effective use of resources and for efficient operations, the current practice is that these processes are handled separately by different agents. This study proposes a hybrid dynamic system, an integrated methodology of taxi path and gate assignment using a knowledge-based decision-making approach to model effectively time-variant and realistic operational features of aircraft gate management and route planning. The model assigns the most suitable parking positions with minimum taxi time and taxi delay among a reduced solution set, satisfying pre-defined decision criteria as well as monitoring ground movements and, if necessary, reassigning new taxi paths and parking positions in real time. Both the proposed integrated methodology and the separate gate assignment and ground management operations currently in use were implemented, analysed and compared in a fast-time simulation model of Istanbul Ataturk Airport (LTBA). The hybrid dynamic assignment model provided significant improvements in taxi times, ground delays and gate utilisation.

The Unmanned Aerial Vehicles (UAVs) become more and more popular due to various potential application fields. This paper studies the distributed leader-follower formation flight control problem of multiple UAVs with uncertain parameters for both the leader and followers. This problem has not been addressed in the literature. Most of the existing literature considers the leader-follower formation control strategy with parametric uncertainty for the followers. However, they do not take the leader parametric uncertainty into account. Meanwhile, the distributed control strategy depends on less information interactions and is more likely to avoid information conflict. The dynamic model of the UAVs is established based on the aerodynamic parameters. The establishment of the topology structure between a collection of UAVs is based on the algebraic graph theory. To handle the parametric uncertainty of the UAVs dynamics, a multivariable model reference adaptive control (MRAC) method is addressed to design the control law, which enables follower UAVs to track the leader UAV. The stability of the formation flight control system is proved by the Lyapunov theory. Simulation results show that the proposed distributed adaptive leader-following formation flight control system has stronger robustness and adaptivity than the fixed control system, as well as the existing adaptive control system.

Several critical load cases during the aircraft design process result from atmospheric turbulence. Thus, rapidly performable and highly accurate dynamic response simulations are required to analyse a wide range of parameters. A method is proposed to predict dynamic loads on an elastically trimmed, large civil aircraft using computational fluid dynamics in conjunction with model reduction. A small-sized modal basis is computed by sampling the aerodynamic response at discrete frequencies and applying proper orthogonal decomposition. The linear operator of the Reynolds-averaged Navier-Stokes equations plus turbulence model is then projected onto the subspace spanned by this basis. The resulting reduced system is solved at an arbitrary number of frequencies to analyse responses to 1-cos gusts very efficiently. Lift coefficient and surface pressure distribution are compared with full-order, non-linear, unsteady time-marching simulations to verify the method. Overall, the reduced-order model predicts highly accurate global coefficients and surface loads at a fraction of the computational cost, which is an important step towards the aircraft loads process relying on computational fluid dynamics.

This paper investigates the effects of the design variables of an aerial deployment mechanism on the robustness of the aerial deployment through a multibody dynamics simulation. The aircraft is modelled as three joined rigid bodies: a right wing, a left wing and a centre body. A spring-loaded hinge is adopted as an actuator for deployment. The design variables are the hinge torque and the deployment timing. The robustness is evaluated using a sigma level method. The margins for the safe deployment conditions are set for the evaluation functions. The dispersive input variables are the initial drop velocity, the surrounding gust velocity, the initial pitch angle and the initial height. The design point with a deployment torque scale value F of 0.7 and a right-wing deployment delay time TSR of 1.0 s can safely deploy in the low-torque deployment condition. This design point is able to accomplish both a safe deployment and a lightweight deployment mechanism.

This paper presents aerodynamic optimisation of tiltrotor blades with high-fidelity computational fluid dynamics. The employed optimisation framework is based on a quasi-Newton method, and the required high-fidelity flow gradients were computed using a discrete adjoint solver. Single-point optimisations were first performed to highlight the contrasting requirements of the helicopter and aeroplane flight regimes. It is then shown how a trade-off blade design can be obtained using a multi-point optimisation strategy. The parametrisation of the blade shape allowed the twist and chord distributions to be modified and a swept tip to be introduced. The work shows how these main blade shape parameters influence the optimal performance of the tiltrotor in helicopter and aeroplane modes, and how an optimised blade shape can increase the overall tiltrotor performance. Moreover, in all the presented cases, the accuracy of the adjoint gradients resulted in a small number of flow evaluations for finding the optimal solution, thus indicating gradient-based optimisation as a viable tool for modern tiltrotor design.

Over the last decades, it has been progressively acknowledged that reducing the specific fuel consumption and the emission of pollutants, as well as improving the thrust-to-weight ratio involves extensive research on advanced sealing technologies. Amongst these, brush seals are particularly well considered for their excellent leakage performance, their low friction properties, and their ability to cope with inevitable rotor excursions during flights. This paper presents the experimental work that has been carried on in order to characterise carbon fibre brush seals leakage rate in function of the bristle pack geometry, under different pressure loads and rotational speeds. The analysed parameters are the bristle-free length, the density and the inter-plate distance. The work, performed by the ULB (Université Libre de Bruxelles) in collaboration with French engine manufacturer Safran Aircraft Engines, highlights specific behaviour of carbon fibre brush seals under differential pressure, proposes a leakage prediction model developed through empirical equations, and discusses over the most influential parameters that influence the air consumption of a brush seal.

This article aims to present a novel control strategy for quadrotor helicopter. It is composed of three main parts constituting the system modelling, the integral back-stepping control, and fuzzy logic compensator. In the first part, a non-linear model is presented taking in consideration some non-linearities and variables that are usually neglected. In the second part, a controller based on the integral back-stepping algorithm has been developed for the system in order to make the system follows a desired path. However, due to complexity of paths and to the presence of unknown disturbances, a fuzzy logic compensator is added in parallel to the integral back-stepping controller to improve trajectory tracking in some critical conditions (high wind speed, mass variation, etc.). Simulation results have been presented to show the effectiveness of the proposed approach.

The performance of a circulation-control inlet guide vane that makes use of the Coanda effect was studied numerically in a high Mach number turbine cascade. The effect of different shapes (elliptic and circular) of the Coanda surface at the blade trailing edge was investigated by implementing both a Coanda jet and a counter-flow blowing. Under high subsonic flow conditions, with a total blowing ratio of 3% of the mainstream, the circulation control cascade can reach the same performance as the reference stator with a 13.5% reduction in the axial chord length, with minimal increase of the energy loss coefficient. The Coanda surfaces with small curvature are more efficient in entraining the mainstream flow, and they achieve better aerodynamic performance. The wall attachment of the Coanda jet is improved by employing counter-flow blowing, resulting in a slight increase of both the exit flow angle and the expansion ratio. Under supersonic flow conditions at the cascade exit, it is more difficult for the circulation control cascade to reach the appropriate flow turning due to a premature shock wave, which is absent in the original cascade until the very end of the suction surface.

Cycloidal rotors are a novel form of propulsion system that can be adapted to various forms of transport such as air and marine vehicles, with a geometrical design differing significantly from the conventional screw propeller. Research on cycloidal rotor design began in the early 1930s and has developed throughout the years to the point where such devices now operate as propulsion systems for various aerospace applications such as micro air vehicles, unmanned air vehicles and compound helicopters. The majority of research conducted on the cycloidal rotor’s aerodynamic performance have not assessed mitigating the dynamic stall effect, which can have a negative impact on the rotor performance when the blades operate in the rotor retreating side. A solution has been proposed to mitigate the dynamic stall effect through employment of active, compliant leading-edge morphing. A review of the current state of the art in this area is presented. A two-dimensional, implicit unsteady numerical analysis was conducted using the commercial computational fluid dynamics software package STAR CCM+, on a two-bladed cycloidal rotor. An overset mesh technique, otherwise known as a chimera mesh, was used to apply complex transient motions to the simulations. Active, compliant leading-edge morphing is applied to an oscillating NACA 0015 aerofoil to attempt to mitigate the dynamic stall whilst maintaining the positive dynamic lift coefficient (Cl) contributions. It was verified that by applying a pulsed input leading-edge rotational morphing schedule, the leading-edge vortex does not fully form and the large flow separation is prevented. Further work in this investigation will focus on coupling the active, leading-edge motion to the cycloidal rotor model with the aim to maximise aerodynamic performance.

The work presented here forms part of a larger project on Large-Eddy Simulation (LES) of aeroengine aeroacoustic interactions. In this paper, we concentrate on LES of near-field flow over an isolated NACA0012 aerofoil at zero angle-of-attack and a chord based Reynolds number of Rec = 2 × 105. A wall-resolved compressible Numerical Large Eddy Simulation (NLES) approach is employed to resolve streak-like structures in the near-wall flow regions. The calculated unsteady pressure/velocity field will be imported into an analyticallybased scheme for far-field trailing-edge noise prediction later. The boundary-layer mean and root-mean-square (rms) velocity profiles, the surface pressure fluctuation over the aerofoil, and the wake flow development are compared with experimental data and previous computational simulations in our research group. It is found that the results from the wall-resolved compressible NLES are very encouraging as they correlate well with test data. The main features of the wall-resolved compressible NLES, as well as the advantages of such compressible NLES over previous incompressible LES performed in our research group, are also discussed.