The deadliest outburst flood from an englacial cavity occurred on Glacier de Tête Rousse in the Mont Blanc area, French Alps, in 1892. A subglacial reservoir was discovered in the same glacier in 2010 and drained artificially in 2010, 2011 and 2012 to protect the 3000 inhabitants downstream. The mechanism leading to the spontaneous refilling of the cavity following these pumping operations has been analyzed. For this purpose, the subglacial water volume changes between 2010 and 2013 were reconstructed. The size of the cavity following the pumping was found to have decreased from 53500 m3 in 2010 to 12 750 m3 in 2013. Creep and the partial collapse of the cavity roof explain a large part of the volume loss. Analysis of cavity filling showed a strong relationship between measured surface melting and the filling rate, with a time delay of 4–6 hours. A permanent input of 15 m3 d−1, not depending on surface melt, was also found. The meltwater and rain from the surface is conveyed to bedrock through crevasses and probably through a permeable layer of rock debris at the glacier bed. The drainage pathway permeability was estimated at 0.054 ms−1 from water discharge measurements and dye-tracing experiments.

The behavior of marine-terminating ice sheets, such as the West Antarctic ice sheet, is of interest due to the possibility of rapid grounding-line retreat and consequent catastrophic loss of ice. Critical to modeling this behavior is a choice of basal rheology, where the most popular approach is to relate the ice-sheet velocity to a power-law function of basal stress. Recent experiments, however, suggest that near-grounding line tills exhibit Coulomb friction behavior. Here we address how Coulomb conditions modify ice-sheet profiles and stability criteria. The basal rheology necessarily transitions to Coulomb friction near the grounding line, due to low effective stresses, leading to changes in ice-sheet properties within a narrow boundary layer. Ice-sheet profiles ‘taper off’ towards a flatter upper surface, compared with the power-law case, and basal stresses vanish at the grounding line, consistent with observations. In the Coulomb case, the grounding-line ice flux also depends more strongly on flotation ice thickness, which implies that ice sheets are more sensitive to climate perturbations. Furthermore, with Coulomb friction, the ice sheet grounds stably in shallower water than with a power-law rheology. This implies that smaller perturbations are required to push the grounding line into regions of negative bed slope, where it would become unstable. These results have important implications for ice-sheet stability in a warming climate.

Mass changes of the Antarctic ice sheet impact sea-level rise as climate changes, but recent rates have been uncertain. Ice, Cloud and land Elevation Satellite (ICESat) data (2003–08) show mass gains from snow accumulation exceeded discharge losses by 82 ± 25 Gt a−1, reducing global sea-level rise by 0.23 mm a−1. European Remote-sensing Satellite (ERS) data (1992–2001) give a similar gain of 112 61 Gt a−1. Gains of 136 Gt a−1 in East Antarctica (EA) and 72 Gt a−1 in four drainage systems (WA2) in West Antarctic (WA) exceed losses of 97 Gt a−1 from three coastal drainage systems (WA1) and 29 Gt a−1 from the Antarctic Peninsula (AP). EA dynamic thickening of 147 Gt a−1 is a continuing response to increased accumulation (>50%) since the early Holocene. Recent accumulation loss of 11 Gt a−1 in EA indicates thickening is not from contemporaneous snowfall increases. Similarly, the WA2 gain is mainly (60 Gt a−1) dynamic thickening. In WA1 and the AP, increased losses of 66 ± 16 Gt a−1 from increased dynamic thinning from accelerating glaciers are 50% offset by greater WA snowfall. The decadal increase in dynamic thinning in WA1 and the AP is approximately one-third of the long-term dynamic thickening in EA and WA2, which should buffer additional dynamic thinning for decades.

The contribution of glaciers to sea-level rise and their effects on landscape evolution depend on the poorly known relationship between sliding speed and drag at the ice/bed interface. Results from experiments with a new rotary laboratory device demonstrate empirically for the first time a double-valued drag relationship like that suggested by some sliding theories: steady drag on a rigid, sinusoidal bed increases, peaks and declines at progressively higher sliding speeds due to growth of cavities in the lee sides of bed undulations. Drag decreases with increased sliding speed if cavities extend beyond the inflection points of up-glacier facing surfaces, so that adverse bed slopes in contact with ice diminish with further cavity growth. These results indicate that shear tractions on glacier beds can potentially decrease due to increases in sliding speed driven by weather or climate variability, promoting even more rapid glacier motion by requiring greater strain rates to produce resistive stresses. Although a double-valued drag relationship has not yet been demonstrated for the complicated geometries of real glacier beds, both its potential major implications and the characteristically convex stoss surfaces of bumps on real glacier beds provide stimulus for exploring the effects of this relationship in ice-sheet models.

We present a detailed, complete glacier inventory for Alaska and neighboring Canada using multi-sensor satellite data from 2000 to 2011. For each glacier, we derive outlines and 51 variables, including center-line lengths, outline types and debris cover. We find 86 723 km2 of glacier area (27 109 glaciers >0.025 km2), ∼12% of the global glacierized area outside ice sheets. Of this area 12.0% is drained by 39 marine-terminating glaciers (74 km of tidewater margin), and 19.3% by 148 lake- and river-terminating glaciers (420 km of lake-/river margin). The overall debris cover is 11%, with considerable differences among regions, ranging from 1.4% in the Kenai Mountains to 28% in the Central Alaska Range. Comparison of outlines from different sources on >2500 km2 of glacierized area yields a total area difference of ∼10%, emphasizing the difficulties in accurately delineating debris-covered glaciers. Assuming fully correlated (systematic) errors, uncertainties in area reach 6% for all Alaska glaciers, but further analysis is needed to explore adequate error correlation scales. Preliminary analysis of the glacier database yields a new set of well-constrained area/length scaling parameters and shows good agreement between our area–altitude distributions and previously established synthetic hypsometries. The new glacier database will be valuable to further explore relations between glacier variables and glacier behavior.

We present novel results of pollen analyses performed on a 10 m firn core retrieved from Alto dell’Ortles glacier (3840 m a.s.l.), Eastern Italian Alps, in 2009. The objective was to identify and quantify pollen grains retained in the ice to detect annual and interannual variations in the pollen spectra, thus enabling construction of an accurate pollen-based timescale. Up to now, this has been achieved by pollen diagram interpretation. Here we present a statistical approach developed to extract the seasonal/annual signal contained in the pollen spectra of an ice core. The method is based on principal component analyses of pollen assemblages obtained by high-level taxonomical identification. We apply this approach to the Ortles samples, demonstrating that seasonal and yearly variations of the pollen spectra are easily detectable and provide valuable information that can help improve the chronological model of the firn core. This approach can potentially be used for deeper cores as well as other types of archives (e.g. varved sediments), allowing faster, more objective estimation of yearly and seasonal variations than with classical percentage pollen diagrams.

Variations in accumulation rate As(t) and temperature Ts(t) at the surface of firn cause changes in the rate of firn compaction (FC) and surface height H(t) that do not involve changes in mass, and therefore need to be accounted for in deriving mass changes from measured H(t). As the effects of changes in As(t) and Ts(t) propagate into the firn, the FC rate is affected with a highly variable and complex response time. The H(t) during measurement periods depend on the history of As(t) and Ts(t) prior to the measurements. Consequently, knowledge of firn response times to climate perturbations is important to estimate the required length of the time series of As(t) and Ts(t) used in FC models. We use our numerical FC model, which is time-dependent on both temperature and accumulation rate, to examine the response times of both H(t) and the rates of change dH(t)/dt to variations in As(t) and Ts(t) using sample perturbations and climate data for selected sites in Antarctica. Our results show that the response times for dH(t)/dt, which are of particular interest, are much shorter than the responses of H(t). Typical response times of dH(t)/dt are from several years to <20 years. The response times are faster in warmer and higher-accumulation areas such as Byrd Station, West Antarctica (4 years), and slower in colder and lower-accumulation areas such as Vostok, East Antarctica (18 years). The response times to temperature are much faster (0.9 year at Byrd and 2.2 years at Vostok), but the corresponding height changes persist much longer. The associated variations in firn density are significantly preserved in the density–depth profiles. For typical fluctuations of surface weather, the Ts(t) from satellite observations since 1982 and As(t) from meteorological data since 1979 are essentially of sufficient length to correct for FC height changes for measurements beginning in 1992.

In this paper we undertake a quantitative analysis of the dynamic process by which ice underneath a dry porous debris layer melts. We show that the incorporation of debris-layer airflow into a theoretical model of glacial melting can capture the empirically observed features of the so-called Østrem curve (a plot of the melt rate as a function of debris depth). Specifically, we show that the turning point in the Østrem curve can be caused by two distinct mechanisms: the increase in the proportion of ice that is debris-covered and/or a reduction in the evaporative heat flux as the debris layer thickens. This second effect causes an increased melt rate because the reduction in (latent) energy used for evaporation increases the amount of energy available for melting. Our model provides an explicit prediction for the melt rate and the temperature distribution within the debris layer, and provides insight into the relative importance of the two effects responsible for the maximum in the Østrem curve. We use the data of Nicholson and Benn (2006) to show that our model is consistent with existing empirical measurements.

A field investigation of iceberg drift pattern and drift speed was conducted in September 2011 in Baffin Bay, northwest Greenland. Ten icebergs were equipped with GPS transponders during a field campaign. Above-waterline dimensions (length, width and height) of the icebergs were measured using a GPS/pressure altimeter and geometrically rectified digital photographs taken during the field campaign. Iceberg lengths, masses and drafts ranged from 95 to 450 m, 330 000 to 17 000 000 t and 70 to 260 m, respectively. The drift patterns and speeds were determined on the basis of GPS positions logged continuously at 1 hour intervals. The drift patterns differed significantly from iceberg to iceberg. The GPS signal was lost on six of the icebergs within the first 23 days of logging. Three transponders were transferring data for more than 5 months until the battery ran out of power. One transponder was sending data until summer 2012. The measured maximum drift speed was 68 cm s−1 (2.4 km h−1), and the mean drift speed for all ten icebergs was 10 cm s−1 (0.4 km h−1). Relations between iceberg size and drift speed were investigated, showing that icebergs with large surface areas moved at the highest speeds, which occurred particularly during strong wind conditions.

The Olympic Peninsula, Washington, USA, currently holds 184 alpine glaciers larger than 0.01 km2 and their combined area is 30.2 ± 0.95 km2. Only four glaciers are >1 km2 and 120 of the others are <0.1 km2. This represents a loss of 82 glaciers and a 34% decrease in combined area since 1980, with the most pronounced losses occurring on south-facing aspects and in the more arid northeastern part of the range. Annual rate of loss in glacier area for seven of the largest glaciers accelerated from 0.26 km2 a−1 (1900–80) to 0.54 km2 a−1 (1980–2009). Thinning rates on four of the largest glaciers averaged nearly 1 ma−1 from 1987 to 2010, resulting in estimated volume losses of 17–24%. Combined glacial snow, firn and ice melt in the Hoh watershed is in the range 63–79 ± 7 × 106 m3, or 9–15% of total May–September streamflow. In the critical August–September period, the glacial fraction of total basin runoff increases to 18–30%, with one-third of the water directly from glacial ice (i.e. not snow and firn). Glaciers in the Elwha basin produce 12–15 ± 1.3 × 106 m3 (2.5–4.0%), while those in the Dungeness basin contribute 2.5–3.1 ± 0.28 × 106 m3 (3.0–3.8%).

New high-resolution velocity maps of the eastern St Elias Mountains, North America, are obtained from speckle tracking of winter 2011 and 2012 RADARSAT-2 image pairs. This includes the most complete velocity mapping to date of Hubbard Glacier, allowing for an upward revision of the Hubbard Glacier calving flux to 5.48 ± 1.16 km3 a−1. Combined with historical velocities from feature tracking of Landsat image pairs (1980s−2000s), and previously published results, these new velocity measurements allow for an evaluation of the interannual variability of motion at eight glaciers in this region, due to both long-term force-balance effects and surge dynamics. Multi-decadal velocities at the non-surge-type Kaskawulsh Glacier indicate little change along most of its length, except for the lowermost 10 km where deceleration has been pronounced since the late 1980s in a region that has undergone rapid recent thinning. Interannual variability of surge-type glaciers was high, with year-to-year velocity variations of up to several hundred m a−1. These glaciers were also characterized by distinct patterns of deceleration and/or acceleration along their length.

Understanding grounding-line dynamics is necessary for predictions of long-term ice-sheet stability. However, despite growing observations of the tidal influence on grounding-line migration, this short-timescale migration is poorly understood, with most modeling attempts assuming beam theory to calculate displacements. Here we present an improved model of tidal grounding-line migration that treats migration as an elastic fracture problem, forced by the additional ocean water pressure from the tide. This new model predicts that the grounding line cannot be assumed to be in hydrostatic equilibrium and, furthermore, that migration is inherently asymmetric and nonlinear, with migration distances that are not proportional to the tidal load. Specifically, for constant surface slope, the grounding line migrates upstream approximately ten times further as the tide rises from mean sea level to high tide than it migrates downstream as the tide falls from mean sea level to low tide, and migration distances are substantially larger than simple flotation arguments suggest. Numerical tests also show that the dependence of migration distance on elastic moduli and ice-sheet thickness are inconsistent with predictions of beam theory for a range of realistic values. Finally, applying the new model to observations in Antarctica results in new estimates of bed slopes, though these estimates remain uncertain due to imperfect knowledge of the relevant rheological parameters.

Flowing snow is a cohesive granular material. Snow temperature and moisture content control the strength of the cohesive bonding between granules and therefore the outcome of granular interactions. Strong, cohesive interactions reduce the free mechanical energy in the avalanche core and therefore play a significant role in defining the avalanche flow regime. We introduce cohesion into avalanche dynamics model calculations by (1) treating cohesion as an additional internal binding energy that must be overcome to expand the avalanche flow volume, (2) modifying the Coulomb stress function to account for the increase in shear because of cohesive interactions and (3) increasing the activation energy to control the onset of avalanche fluidization. The modified shear stress function is based on force measurements in chute experiments with flowing snow. Example calculations are performed on ideal and real terrain to demonstrate how snow cohesion modifies avalanche flow and runout behaviour.

Most glaciers on the Tibetan Plateau are difficult to assess as they are located in remote regions at high altitude. This study focuses on the surface energy-balance (SEB) and mass-balance (MB) characteristics of Purogangri ice cap (PIC). A ‘COupled Snowpack and Ice surface energy and MAss balance model’ (COSIMA) is applied without observational data from the ground. The model is forced by a meteorological dataset from the High Asia Refined analysis. Model results for annual surface-elevation changes and MB agree well with the results of a previous remote-sensing estimate. Low surface velocities of 0.026 ± 0.012 m d−1 were measured by repeat-pass InSAR. This finding supports the validation of the steady-state COSIMA against satellite-derived surface changes. Overall MB of PIC for the period 2001–11 is nearly balanced (−44 kg m−2 a−1). Analysis of the model-derived SEB/MB components reveals that a significant amount of snowfall in spring is responsible for high surface albedo throughout the year. Thus, the average surface energy loss through net longwave radiation is larger than the energy gain through net shortwave radiation. The dry continental climate favours mass loss through sublimation, which accounts for 66% of the total mass loss.

Satellite altimetric time series allow high-precision monitoring of ice-sheet mass balance. Understanding elevation changes in these regions is important because outlet glaciers along ice-sheet margins are critical in controlling flow of inland ice. Here we discuss a new airborne altimetry dataset collected as part of the ICECAP (International Collaborative Exploration of the Cryosphere by Airborne Profiling) project over East Antarctica. Using the ALAMO (Airborne Laser Altimeter with Mapping Optics) system of a scanning photon-counting lidar combined with a laser altimeter, we extend the 2003–09 surface elevation record of NASA’s ICESat satellite, by determining cross-track slope and thus independently correcting for ICESat’s cross-track pointing errors. In areas of high slope, cross-track errors result in measured elevation change that combines surface slope and the actual Δz/Δt signal. Slope corrections are particularly important in coastal ice streams, which often exhibit both rapidly changing elevations and high surface slopes. As a test case (assuming that surface slopes do not change significantly) we observe a lack of ice dynamic change at Cook Ice Shelf, while significant thinning occurred at Totten and Denman Glaciers during 2003–09.

Radio-glaciological parameters from the Moore’s Bay region of the Ross Ice Shelf, Antarctica, have been measured. The thickness of the ice shelf in Moore’s Bay was measured from reflection times of radio-frequency pulses propagating vertically through the shelf and reflecting from the ocean, and is found to be 576 ± 8 m. Introducing a baseline of 543 ± 7m between radio transmitter and receiver allowed the computation of the basal reflection coefficient, R, separately from englacial loss. The depth-averaged attenuation length of the ice column, 〈L〉 is shown to depend linearly on frequency. The best fit (95% confidence level) is 〈L(ν)〉= (460±20) − (180±40)ν m (20 dB km−1), for the frequencies ν = [0.100–0.850] GHz, assuming no reflection loss. The mean electric-field reflection coefficient is (1.7 dB reflection loss) across [0.100–0.850] GHz, and is used to correct the attenuation length. Finally, the reflected power rotated into the orthogonal antenna polarization is <5% below 0.400 GHz, compatible with air propagation. The results imply that Moore’s Bay serves as an appropriate medium for the ARIANNA high-energy neutrino detector.

To better understand recent rapid recession of marine-terminating glaciers in Greenland, we performed satellite and field observations near the calving front of Bowdoin Glacier, a 3 km wide outlet glacier in northwestern Greenland. Satellite data revealed a clear transition to a rapidly retreating phase in 2008 from a relatively stable glacier condition that lasted for >20 years. Ice radar measurements showed that the glacier front is grounded, but very close to the floating condition. These results, in combination with the results of ocean depth soundings, suggest bed geometry in front of the glacier is the primary control on the rate and pattern of recent rapid retreat. Presumably, glacier thinning due to atmospheric and/or ocean warming triggered the initial retreat. In situ measurements showed complex short-term ice speed variations, which were correlated with air temperature, precipitation and ocean tides. Ice speed quickly responded to temperature rise and a heavy rain event, indicating rapid drainage of surface water to the bed. Semi-diurnal speed peaks coincided with low tides, suggesting the major role of the hydrostatic pressure acting on the calving face in the force balance. These observations demonstrate that the dynamics of Bowdoin Glacier are sensitive to small perturbations occurring near the calving front.

We develop a formal thin-plate treatment of the viscoelastic flexure of floating ice shelves as an initial step in treating various problems relevant to ice-shelf response to sudden changes of surface loads and applied bending moments (e.g. draining supraglacial lakes, iceberg calving, surface and basal crevassing). Our analysis is based on the assumption that total deformation is the sum of elastic and viscous (or power-law creep) deformations (i.e. akin to a Maxwell model of viscoelasticity, having a spring and dashpot in series). The treatment follows the assumptions of well-known thin-plate approximation, but is presented in a manner familiar to glaciologists and with Glen’s flow law. We present an analysis of the viscoelastic evolution of an ice shelf subject to a filling and draining supraglacial lake. This demonstration is motivated by the proposition that flexure in response to the filling/drainage of meltwater features on the Larsen B ice shelf, Antarctica, contributed to the fragmentation process that accompanied its collapse in 2002.

Ice cores provide a robust reconstruction of past climate. However, development of timescales by annual-layer counting, essential to detailed climate reconstruction and interpretation, on ice cores collected at low-accumulation sites or in regions of compressed ice, is problematic due to closely spaced layers. Ice-core analysis by laser ablation–inductively coupled plasma–mass spectrometry (LA-ICP-MS) provides sub-millimeter-scale sampling resolution (on the order of 100 μm in this study) and the low detection limits (ng L−1) necessary to measure the chemical constituents preserved in ice cores. We present a newly developed cryocell that can hold a 1 m long section of ice core, and an alternative strategy for calibration. Using ice-core samples from central Greenland, we demonstrate the repeatability of multiple ablation passes, highlight the improved sampling resolution, verify the calibration technique and identify annual layers in the chemical profile in a deep section of an ice core where annual layers have not previously been identified using chemistry. In addition, using sections of cores from the Swiss/Italian Alps we illustrate the relationship between Ca, Na and Fe and particle concentration and conductivity, and validate the LA-ICP-MS Ca profile through a direct comparison with continuous flow analysis results.

Controls on the global distribution of surge-type glaciers hold the keys to a better understanding of surge mechanisms. We investigate correlations between the distribution of surge-type glaciers and climatic and glacier geometry variables, using a new global geodatabase of 2317 surge-type glaciers. The highest densities of surge-type glaciers occur within an optimal climatic envelope bounded by temperature and precipitation thresholds. Across all regions with both surge-type and normal glaciers, the former are larger, especially at the cold, dry end of the climatic spectrum. A species distribution model, Maxent, accurately predicts the major clusters of surge-type glaciers using a series of climatic and glacier geometry variables, but under-predicts clusters found outside the climatically optimal surge zone. We interpret the results in terms of a new enthalpy cycle model. Steady states require a balance between enthalpy gains generated by the balance flux and losses via heat conduction and meltwater discharge. This condition can be most easily satisfied in cold, dry environments (thin, low-flux glaciers, efficient conductive heat losses) and warm, humid environments (high meltwater discharges). Intermediate conditions correspond to the optimal surge zone, where neither heat conduction nor runoff can effectively discharge enthalpy gains, and dynamic cycling can result.