Laser-driven X-rays as probes for high-energy-density physics spans an extremely large parameter space with laser intensities varying by 8 orders of magnitude. We have built and characterized a soft X-ray source driven by a modest intensity laser of 4 × 1013 W/cm2. Emitted X-rays were measured by diamond radiation detectors and a filtered soft X-ray camera. A material-dependence study on Al, Ti, stainless steel alloy 304, Fe, Cu and Sn targets indicated 5-μm-thick Cu foils produced the highest X-ray yield. X-ray emission in the laser direction and emission in the reverse direction depend strongly on the foil material and the thickness due to the opacity and hydrodynamic disassembly time. The time-varying X-ray signals are used to measure the material thinning rate and is found to be ∼1.5 μm/ns for the materials tested implying thermal temperature around 0.6 eV. The X-ray spectra from Cu targets peaks at ∼2 keV with no emission >4 keV and was estimated using images with eight different foil filters. One-dimensional hydrodynamic and spectral calculations using HELIOS-CR provide qualitative agreement with experimental results. Modest intensity lasers can be an excellent source for nanosecond bursts of soft X-rays.

The interaction of focused high power laser beam with solid targets leads to acceleration of charged particles among other by non-linear effects in the plasma. In this experiment, the hot electrons are characterized from the interaction of sub-nanosecond and kilo-joule class laser pulse with thin metal foil targets (Cu, Ta, Ti, Sn, Pb). The energy distribution functions of electrons were measured by angularly resolved multichannel electron spectrometer. The hot electron temperatures were observed in range from 30 to 80 keV for laser intensities between ${\sim}10^{15}$ and $3 \times 10^{16}\ \mathrm{W\,cm^{-2}}$. The measured energy distribution and electron temperature were compared with published results and known scaling laws at higher laser intensities. For foil targets of different materials, the temperature and flux of hot electrons were scaled with target thickness in the range of 1–100 $\unicode{x03BC}\mathrm{m}$ from low Z to high Z materials where Z is the atomic number. The profile of conversion efficiency from laser energy to hot electrons is discussed in the energy range from 100 to 600 J. For the given laser and target parameters, the nonlinear behaviour of conversion efficiency and relevant physics are also described in detail.

A partition calculation method (PCM) for calculating the diffraction efficiency of multilayer Fresnel zone plate with high aspect ratio is proposed. In contrast to the traditional theory, PCM designs and evaluates Fresnel zone plate (FZP) considering material pairs, all zone widths, thicknesses and X-ray energy more completely. The results obtained through PCM are validated by comparing them with the complex amplitude superposition theory and coupled wave theory numerical results. The PCM satisfies the requirements of the theoretical investigation of FZP with small outermost zone width (drN) and large thickness (t). Combining proper numerical analysis with the experimental conditions will present a great potential to break through the imaging performance of X-ray microscopy.

The proton–boron ${}^{11}{\text{B}}\left( {p,\alpha } \right)2\alpha $ reaction (p-11B) is an interesting alternative to the D-T reaction ${\text{D}}\left( {{\text{T}},{\text{n}}} \right)\alpha $ for fusion energy, since the primary reaction channel is aneutronic and all reaction partners are stable isotopes. We measured the α production yield using protons in the 120–260 keV energy range impinging onto a hydrogen–boron-mixed target, and for the first time present experimental evidence of an increase of α-particle yield relative to a pure boron target. The measured enhancement factor is approximately 30%. The experiment results indicate a higher reactivity, and that may lower the condition for p-11B fusion ignition.

We have experimentally investigated the collisionless shock acceleration of ions via the interaction of a relativistic intensity (3 × 1019 W/cm2), 1.053 µm wavelength laser pulse with an underdense plasma. This plasma is formed through the use of a novel cluster jet design that allows for control of the plasma peak density and front scale length without the use of additional plasma-forming laser pulses. When the front density scale length of the target plasma is less than 60 µm, the laser pulse (1 J, 400 fs) is capable of launching an electrostatic shock wave that accelerates a proton beam. This beam is shown to have a narrow divergence angle of 0.8°, a peak flux of 14 × 106 protons/sr with an ion energy exceeding 440 keV. Particle-in-cell simulations indicate this narrow ion beam is produced by converging shocks generated via filamentation of the laser pulse in high-density (near critical) plasma.