Propulsion systems have revolutionised human activities and made the world smaller. They have brought transport advances that enabled the conversion of dreams into reality. Very large international high-technology investments are being made to continue to develop efficient and affordable gas turbine and ramjet propulsion while implementing knowledge that is bringing large environmental benefits.

The work presented here forms part of a larger project on Large-Eddy Simulation (LES) of aeroengine aeroacoustic interactions. In this paper, we concentrate on LES of near-field flow over an isolated NACA0012 aerofoil at zero angle-of-attack and a chord based Reynolds number of Rec = 2 × 105. A wall-resolved compressible Numerical Large Eddy Simulation (NLES) approach is employed to resolve streak-like structures in the near-wall flow regions. The calculated unsteady pressure/velocity field will be imported into an analyticallybased scheme for far-field trailing-edge noise prediction later. The boundary-layer mean and root-mean-square (rms) velocity profiles, the surface pressure fluctuation over the aerofoil, and the wake flow development are compared with experimental data and previous computational simulations in our research group. It is found that the results from the wall-resolved compressible NLES are very encouraging as they correlate well with test data. The main features of the wall-resolved compressible NLES, as well as the advantages of such compressible NLES over previous incompressible LES performed in our research group, are also discussed.

Internet applications have been extended to various aspects of everyday life and offer services of high reliability and security at relatively low cost. This project presents the design of a reliable, safe and secure software system for real-time remote operation and monitoring of an aero gas turbine with utilisation of existing internet technology, whilst the gas turbine is installed in a remote test facility

This project introduces a capability that allows remote and flexible operation of an aero gas turbine throughout the whole operational envelope, as required by the user at low cost, by exploiting the available Internet technology. Remote operation of the gas turbine can be combined with other remote Internet applications to provide very powerful gas-turbine performance-simulation experimental platforms and real-time performance monitoring tools, whilst keeping the implementation cost at low levels.

The gas turbine used in this experiment is an AMT Netherlands Olympus micro gas turbine and a spiral model approach was applied for the software. The whole process was driven by risk mitigation.

The outcome is a fully functional software application that enables remote operation of the micro gas turbine whilst constantly monitors the performance of the engine according to basic gas turbine control theory. The application is very flexible, as it runs with no local installation requirements and includes provisions for expansion and collaboration with other online performance simulation and diagnostic tools.

The flow and heat transfer characteristics over a single dimple and an array of staggered dimples have been investigated using the Reynolds Averaged Navier-Stokes (RANS) approach. The objective is to determine how reliably RANS models can predict this type of complex cooling flows. Three classes of low-Reynolds number RANS models have been employed to represent the turbulence. These included a linear Eddy Viscosity Model (EVM), a Non-Linear Model (NLEVM) and a Reynolds Stress transport Model (RSM). Variants of the k-ε model have been used to represent the first two categories. Steady and time-dependent simulations have been carried out at a bulk Reynolds number of around 5,000 with dimple print diameter to channel height ratios of D/H = 1.0, 2.0 and ratios of dimple depth to channel height of δ/H = 0.2, 0.4. The linear EVM and the RSM tested both produce symmetric circulations in the dimples, while the NLEVM produces an asymmetric pattern. The mean velocity profiles predicted numerically are generally in good agreement with the data. The main flow characteristics are reproduced by the RANS models, but some predictive deviations from available data point to the need for further investigations. All models report an overall enhancement in heat transfer levels when using dimples in comparison to those of a plane channel.

The Lean Direct Injection (LDI) combustor is one of the low-emissions combustors with great potential in aero-engine applications, especially those with high overall pressure ratio. A preliminary design tool providing basic combustor sizing information and qualitative assessment of performance and emission characteristics of the LDI combustor within a short period of time will be of great value to designers. In this research, the methodology of preliminary aerodynamic design for a second-generation LDI (LDI-2) combustor was explored. A computer code was developed based on this method covering the design of air distribution, combustor sizing, diffuser, dilution holes and swirlers. The NASA correlations for NOx emissions are also embedded in the program in order to estimate the NOx production of the designed LDI combustor. A case study was carried out through the design of an LDI-2 combustor named as CULDI2015 and the comparison with an existing rich-burn, quick-quench, lean-burn combustor operating at identical conditions. It is discovered that the LDI combustor could potentially achieve a reduction in liner length and NOx emissions by 18% and 67%, respectively. A sensitivity study on parameters such as equivalence ratio, dome and passage velocity and fuel staging is performed to investigate the effect of design uncertainties on both preliminary design results and NOx production. A summary on the variation of design parameters and their impact is presented. The developed tool is proved to be valuable to preliminarily evaluate the LDI combustor performance and NOx emission at the early design stage.

Gas path diagnostics is one of the most effective condition monitoring techniques in supporting condition-based maintenance of gas turbines and improving availability and reducing maintenance costs of the engines. The techniques can be applied to the health monitoring of different gas path components and also gas path measurement sensors. One of the most important measurement sensors is that for the engine control, also called the power setting sensor, which is used by the engine control system to control the operation of gas turbine engines. In most of the published research so far, it is rarely mentioned that faults in such sensors have been tackled in either engine control or condition monitoring. The reality is that if such a sensor degrades and has a noticeable bias, it will result in a shift in engine operating condition and misleading diagnostic results.

In this paper, the phenomenon of a power-setting sensor fault has been discussed and a gas path diagnostic method based on a Genetic Algorithm (GA) has been proposed for the detection of power-setting sensor fault with and without the existence of engine component degradation and other gas path sensor faults. The developed method has been applied to the diagnostic analysis of a model aero turbofan engine in several case studies. The results show that the GA-based diagnostic method is able to detect and quantify the power-setting sensor fault effectively with the existence of single engine component degradation and single gas path sensor fault. An exceptional situation is that the power-setting sensor fault may not be distinguished from a component fault if both faults have the same fault signature. In addition, the measurement noise has small impact on prediction accuracy. As the GA-based method is computationally slow, it is only recommended for off-line applications. The introduced GA-based diagnostic method is generic so it can be applied to different gas turbine engines.

Installation effects on the S-duct intakes of a high power turboprop were investigated by comparing three different nacelle configurations as the channel wing, over-the-wing and conventional tractor wing using computational fluid dynamic methods. The interaction of the propeller, the wing, and the nacelle on the scoop type turboprop intakes were identified in terms of recovery and distortion on the aerodynamic interface planes. An actuator disc model was used to simulate the propeller downstream effects. The channel wing installation of S-ducts showed approximately 2% higher total pressure recovery than the other configurations. The channel wing configuration with a wrap-around S-duct experienced a 2% lower circumferential distortion intensity, whereas over-the-wing had an increase by 3% in comparison to the tractor wing. It was also observed that the S-duct type had a greater influence on the radial distortion intensity than the installation type. The swirl coefficient distribution showed that multiple peaks occurred as opposed to swirl results based on a single sector of the aerodynamic interface plane. The difference between swirl peaks of shaft penetration S-duct was reduced by 14% when installed on channel wing, whereas the peaks of wrap-around experienced 90° phase shift, and their difference showed 10% increase on channel wing.

The results of extensive experimental testing of an aero-engine air-oil separator are presented and discussed. The study focuses on the pressure loss of the system. Oil enters the device in the form of dispersed droplets. Subsequently, separation occurs by centrifuging larger droplets towards the outer walls and by film formation at the inner surface of a rotating porous material, namely an open-cell metal foam. The work described here is part of a study led jointly by the Karlsruhe Institute of Technology (KIT) and the University of Nottingham (UNott) within a recent EU project.

The goal of the research is to increase the separation efficiency to mitigate oil consumption and emissions, while keeping the pressure loss as low as possible. The aim is to determine the influencing factors on pressure loss and separation efficiency. With this knowledge, a correlation can eventually be derived. Experiments were conducted for three different separator configurations, one without a metal foam and two with metal foams of different pore sizes. For each configuration, a variety of engine-like conditions of air mass flow rate, rotational speed and droplet size was investigated. The experimental results were used to validate and improve the numerical modelling.

Results for the pressure drop and its dependencies on air mass flow rate and the rotational speed were analysed. It is shown that the swirling flow and the dissipation of angular momentum are the most important contributors to the pressure drop, besides the losses due to friction and dissipation caused by the flow passing the metal foam. It was found that the ratio of the rotor speed and the tangential velocity of the fluid is an important parameter to describe the influence of rotation on the pressure loss. Contrary to expectations, the pressure loss is not necessarily increased with a metal foam installed.

New commercial aero engines for 2050 are expected to have lower specific thrusts for reduced noise and improved propulsive efficiency, but meeting the ACARE Flightpath 2050 fuel-burn and emissions targets will also need radical design changes to improve core thermal efficiency. Intercooling, recuperation, inter-turbine combustion and added topping and bottoming cycles all have the potential to improve thermal efficiency. However, these new technologies tend to increase core specific power and reduce core mass flow, giving smaller and less efficient core components. Turbine cooling also gets more difficult as engine cores get smaller. The core-size-dependent performance penalties will become increasingly significant with the development of more aerodynamically efficient and lighter-weight aircraft having lower thrust requirements. In this study the effects of engine thrust and core size on performance are investigated for conventional and intercooled aeroengine cycles. Large intercooled engines could have 3%–4% SFC improvement relative to conventional cycle engines, while smaller engines may only realize half of this benefit. The study provides a foundation for investigations of more complex cycles in the EU Horizon 2020 ULTIMATE programme.

In the article by Rolt(1), there was an error in Equation (2). The correct equation is republished here. 2

$$\begin{equation} {W_c} = \ \frac{{{W_{\it cref}}\left( {{T_{\it grel}} - {T_{\it cref}}} \right){{({W_4}/{W_{\it 4ref}})}^{0.65}}}}{{\left( {{T_{\it gref}} - {T_c}} \right)}}\ \ \ \ \ \ \ \end{equation}$$

Deposit formation on turbine hardware in propulsion turbine engines can occur in many arid regions globally. Characterising crystalline deposits on metallic substrates can aid in component resilience and health monitor algorithms during particle ingestion. This study has developed two statistical empirical models for prediction from acquired experimental data for the onset of deposits. The prediction models are for crystalline particulate (Arizona Road Test Dust) deposits on a flat rectangular Hastelloy-X test coupon. Particle impingement angles varied between 20° and 80° in experimental flow temperatures of 1,000–1,100°C. Averaged deposits are methodically quantified through normalised particle deposit tallies per area and percent coverage of the surface using microscopic imaging and image processing programs. Deposit accumulation is a quadratic function of both near-surface coupon temperature and coupon angle.

The rotor sub-assembly of the high-pressure turbine of a modern turbofan engine is typically free to move downstream because of the force imbalance acting on the disc and blades following an un-located shaft failure. This downstream movement results in a change in the geometry of the rotor blade, tip seals and rim/platform seals because of the interaction of the rotor sub-assembly with the downstream vane sub-assembly. Additionally, there is a change in the leakage flow properties, which mix with the main flow because of the change in engine behaviour and secondary air system dynamics. In the present work, the changes in geometry following the downstream movement of the turbine, are obtained from a validated friction model and structural LS-DYNA simulations. Changes in leakage flow properties are obtained from a transient network source-sink secondary air system model. Three-dimensional Reynolds-averaged Navier-Stokes simulations are used to evaluate the aerodynamic effect from the inclusion of the leakage flows, tipseal domains, and downstream movement of the rotor for three displacement configurations (i.e. 0, 10 and 15 mm) with appropriate changes in geometry and leakage flow conditions. It is observed from the results that there is a significant reduction in the expansion ratio, torque and power produced by the turbine with the downstream movement of the rotor because of changes in the flow behaviour for the different configurations. These changes in turbine performance parameters are necessary to accurately predict the terminal speed of the rotor using an engine thermodynamic model. Further, it is to be noted that such reductions in turbine rotor torque will result in a reduction of the terminal speed attained by the rotor during an un-located shaft failure. Therefore the terminal speed of the rotor can be controlled by introducing design features that will result in the rapid rearward displacement of the turbine rotor.