In this paper, the basic quadratic form of the poly-harmonic distortion model is first presented and this is then extended to provide a new, modified quadratic poly-harmonic distortion model. Comparisons between the X-parameter model, the basic quadratic poly-harmonic distortion model, and the modified version are provided. Both simulation and experimental test results show that the new modified model provides significant improvements in accuracy, not only for the fundamental frequency, but also for DC. Work on the optimization of the model is also presented, providing further improvements in both the model extraction time and the file size.

A 24 GHz low-power transceiver is designed, fabricated, and characterized using 130 nm complementary metal-oxide semiconductor (CMOS) process. The designed transceiver is targeted for frequency-modulated-continuous-wave (FMCW) wireless local positioning. The transceiver includes four switchable receiving channels, one transmitting channel and local-oscillator generation circuitries. Several power-saving techniques are implemented, such as switch channel and adaptive mixer biasing. The design aspects of the low-power circuit blocks and integration considerations are presented in details. The integrated transceiver has a chip area of only 2.2 mm × 1.7 mm. In transmitting mode the transceiver achieves an output power of 4 dBm and phase noise of −90 dBc/Hz at 1 MHz, while consuming 75 mW power consumption under 1.5 V power supply. In switch-channel receiving mode the transceiver demonstrates 31 dB gain and 6 dB noise figure with 65 mW power consumption. The transceiver measurements compare well with the simulated results and achieve state-of-the-art performance with very low-power consumption.

A microwave rectifier at 5.8 GHz without any capacitors is presented, which owns a measured MW-to-DC conversion efficiency of 68.1%. A harmonic rejection filter and a DC pass filter, which replace lumped capacitors in conventional microwave rectifiers, are applied to suppressing the harmonics produced by an HSMS-286 Schottky diode during rectifying. At the fundamental frequency, a microstrip impedance transformer which contains a shunt λg/8 short-ended microstrip transmission line and two short series microstrip transmission lines are applied to compensating the imaginary impedance of the diode and matching the input impedance of the rectifier. The measured MW-to-DC conversion efficiency agrees well to the simulated results. The novel rectifier without any lumped passive elements may be applied for power transmission system at higher microwave frequencies.

A new ultra-high frequency radio frequency identification (RFID) tag antenna, which is comprised a U-shaped tuning stub and a dipole radiator for different permittivity surfaces is investigated, fabricated, and measured. For a conjugate match to the NXP G2XM chip impedance of 29–j137 at 915 MHz, a dipole tag antenna with U-shaped stubconnected to dipole arms was designed. Simple size adjustments of the U-shaped tuning stub and dipole radiator of the antenna allow for easy control of the antenna resistance and inductive reactance, from which the chip impedance requirement may be readily satisfied. The read range of the prototype antenna attached on a different permittivity surfaces (εr = 1–4) can reach more than 4.5 m, which has been tested for an RFID reader with 4.0 W of effective isotropic radiated power. The antenna structure consists of two dipole load bars and two loop electrically connected. The design offers more choice of freedom to tune the input impedance of the proposed antenna. Measurement data are presented which are in good agreement with simulation results. The design is suitable for mounting on all kinds of objects. The fabricated tag sensitivity of −3 dBm, read range of 7 m on the x–z and y–z planes, and the measured orientation radiation patterns were obtained in the desired frequency band.

A Ka-band carrier generator using phase-locked loop (PLL) frequency synthesizer is presented in this paper. The design uses integer-N PLL chip PE83336 as the important hardware support. The key idea of generating Ka-band frequency signal with low-phase noise is to generate a high-quality X-band frequency signal using PLL frequency synthesizer and employ a frequency multiplier to deliver the high-frequency output at the desired frequency band. Experimental measurements of the frequency synthesizer demonstrate the excellent performance, which is achieved with the Ka-band output with a frequency resolution of 5.7 MHz and phase noise better than −70 dBc/Hz at 1 kHz.

Prediction of millimeter(mm)-wave radio signals can be beneficial in recreating and repeating atmospheric conditions in a controlled, laboratory environment. A path-loss model has been proposed that accounts for free-space losses, oxygen absorption, reflection and diffraction losses, and rain-rate attenuation at mm-wave frequencies. Two variable passive low-pass-integrated circuit filter structures for attenuation in the 57–64 GHz unlicensed frequency band have been proposed, designed, simulated, prototyped in a 130-nm SiGe bipolar complementary metal-oxide semiconductor process, and measured. The filters are based on the Butterworth and Chebyshev low-pass filter topologies and investigate the possibility of using the structures to perform amplitude attenuation of mm-wave frequencies over a short distance. Both filters are designed and matched for direct coupling with equivalent circuit models of dipole antennas operating in this frequency band. Full integration therefore allows prediction of atmospheric losses on an analog, real-time, basis without the requirement of down-converting (sampling) to analyze high-frequency signals through a digital architecture. On-wafer probe measurements were performed to limit parasitic interference from bonding wires and enclosed packaging.

A reconfigurable band-pass filter with switchable bandwidth, for wireless applications is demonstrated using a dual-mode microstrip square-loop resonator. The proposed filter has been designed on Rogers RO4003C and achieves switchable bandwidth by changing the length of two tuning stubs with the implementation of two strategically placed p-i-n diodes as switching elements. The filter was designed with a center frequency of 2.4 GHz and the two distinct operation states have bandwidths, 113 MHz (4.8%) with an insertion loss of 1.2 dB and 35 MHz (1.5%) with an insertion loss of 1.5 dB. The physical size of the fabricated reconfigurable filter including the implementation of the DC bias lines is comparable to the size of a conventional filter.

This work presents a novel frequency miniaturized reconfigurable dual-mode stub-loaded resonator switchable from bandpass filter to single/double-notched bandnotch filter. The proposed filter topology employs RF PIN diodes as the switching device. Based on the odd- and even-mode equivalent circuits, the resonant characteristics of the proposed microstrip resonator are investigated. The defected ground structure pattern enhanced the performance; the 3-dB bandwidth reached 63%, with insertion loss of −0.5 dB. There was great sharpness of 55 dB in the low-frequency edge (from 1.7982 to 1.8466 GHz) and 33 dB in the high-frequency edge (from 3.4329 to 3.4995 GHz). The frequency-reconfigurable microstrip filter has been designed, fabricated, and measured for application in narrow band and ultra-wideband.

Millimeter-wave reconfigurable bandpass filters with the ability to operate between 60 GHz and the E-band, capable of providing good channel isolation, are presented. A fully integrated filter with all reconfigurable elements embedded for compactness and a switchable filter that uses radio frequency micro-electro-mechanical system (RF MEMS) single-pole double-throw switches are designed. A new method that increases fractional bandwidths is introduced. It uses inductively coupled inverters without requiring their tuning. New circuit models are offered for inverters, reconfigurable resonators, and reconfigurable bandstop stubs. Our compact bandpass filter achieved a footprint of only 4.75 mm × 3.75 mm. Measurements for our filters show good agreement with the results of simulations.

A new compact quad-passband bandpass filter (BPF) using multi-mode resonators (MMRs) based on multi-layered substrate technique is proposed. The filter consists of a pair of multi-mode resonators (uniform impedance resonator and stepped impedance resonator) operated at 1.8/3.7 GHz on top layer and the other pair of the multi-mode resonators operated at 2.4/3 GHz on bottom layer. Source–load coupling lines are used to be the input/output (I/O) ports for providing the multi-paths propagations by cross-coupling effects in the filter. Specifically, the operated frequencies of the filter at 1.8/2.4/3/3.7 GHz with bandwidths of 6.7, 8.2, 4.6, and 7.2% are successfully designed and implemented. The proposed filter is useful for the multi-passband filters design, especially when the passbands are needed to be very close.

This work demonstrates design methods that can achieve remarkable enhancement in the stopband response of microstrip coupled-line filters. The frequencies of resonance and/or the transmission zeros of a coupled-line section can be controlled by its length. Therefore, by constructing a filter with coupled lines of incommensurate lengths such that these frequencies do not overlap, substantial improvement in the stopband response can be obtained. Besides its compact structure and simple design procedure, an unprecedented performance is demonstrated experimentally in which the transmission level is maintained below −20 dB up to as high as 11.9 f0 for a third-order filter, where f0 is the center frequency.

In this paper, we show a second-order (four-resonator) absorptive bandstop filter circuit topology which gives a larger bandwidth compared to a first-order topology. Due to the absorptive characteristic, it creates a large attenuation at the center frequency using low-Q resonators. Since low-Q resonators can be used in generating a large attenuation, small-size resonators can be employed in bandstop filter design. Analytic design equations are provided so that a higher-order absorptive bandstop filter can be designed analytically. It is also shown that the second-order filter topology exhibits a better frequency selectivity having a same bandwidth. The proposed filter topology has been applied to a design of a miniaturized low-temperature co-fired ceramic bandstop filter with low-Q resonators. The Q-factor of the lumped-element resonators has been chosen to be 5 for demonstration.

A new microstrip lowpass filter with compact size and ultra-wide stopband using T-shaped resonator is proposed. To make smaller the circuit size of the filter, cursive transmission line is also suggested. Moreover, exact equation of most important transmission zero is calculated based on LC equivalent circuit and transformation function. A demonstration filter with 3 dB cut-off frequency at 1.02 has been designed, fabricated, and measured. Results show that a relative stopband band width of 166.3% (referred to suppression degree of 20 dB) is achieved while obtaining high figure of merit of 46 274.

In this paper, we propose a new design of metamaterial and electromagnetic bandgap (EBG) structure based on double layers of metallic grids. Using finite integration technique, the electromagnetic properties of the grid structure have been investigated and this structure has been employed to enhance the performance of a patch antenna working at 11 GHz. The surface waves in the substrate of antenna have been suppressed by EBG behavior of the grid when used as a substrate, and it improves its gain to 9.21 dB from 5.64 dB. When this structure is also used as superstrate of the antenna, the gain up to 13 dB has been achieved due to its metamaterial behavior. Congregation effect of metamaterial provides a huge improvement in the directionality of the antenna and its half power beam width (HPBW) has been improved to 32.7° and 31.5° from 108.3° and 93.5° in E-and H-planes, respectively.

In this paper, a substrate-integrated waveguide (SIW) H-plane horn antenna has been designed for X-band applications. Metamaterial is incorporated for performance enhancement of the designed antenna. Capacitively loaded loop is used as the unit cell of metamaterial for achieving negative values of relative permittivity and relative permeability. A half-mode SIW H-plane horn antenna is also proposed in this paper which reduces the size of the antenna without much effect on its performance. Metamaterial is integrated on the half-mode horn as well for improvement in gain and radiation pattern. The antennas are fabricated and tested. Excellent agreement between the measured and simulated results was obtained.

Design analysis of multiband-coupled stacked sectoral antenna array with finite ground plane using high low dielectric constant substrates is proposed in this paper for modern communication systems and applied physics. Multiband planar antennas have been extensively developed due to demands for integration of wireless communication systems. In this paper, we present the design and development of a multiband microstrip antenna array with parasitic coupling and stacking using two different substrates. The stacked designed antenna resonates at three different frequencies: 3.8, 5.4, and 10 GHz; therefore, showing a multiband property with good radiation (far-field) characteristics. A significant comparison study is also presented considering different dielectric constant substrates. The proposed antenna is an attractive solution for different wireless communication systems such as mobile systems, satellite systems, etc.

This paper proposes a novel and simple expression for effective radius of annular-ring microstrip antennas (ARMAs) obtained using a recently emerged optimization algorithm of artificial bee colony (ABC) in calculating the resonant frequency at dominant mode (TM11). A total of 80 ARMAs having different parameters related to antenna dimensions and dielectric constants was simulated in terms of the resonant frequency with the help of an electromagnetic simulation software called IE3D™ based on method of moment. The effective radius expression was constructed and the unknown coefficients belonging to the expression were then optimally determined with the use of ABC algorithm. The proposed expression was verified through comparisons with the methods of resonant frequency calculation reported elsewhere. Also, it was further validated on an ARMA fabricated in this study. The superiority of the presented approach over the other methods proposed in the literature is that it does not need any sophisticated computations while achieving the most accurate results in the resonant frequency calculation of ARMAs.

A compact navigation receiver comprising a decoupled and matched four-element L1-band antenna array with an inter-element separation of a quarter of the free-space wavelength is presented in this paper. We investigate the impact of the decoupling and matching network on the robustness of the navigation receiver. It is observed that in order to achieve high robustness with a compact antenna array, it is necessary to employ a decoupling and matching network, particularly in case of three spatially separated interferers. Furthermore, we study the influence of the polarization impurity of the compact planar antenna array on the equivalent carrier-to-interference-plus-noise ratio (CINR) of the receiver when impinged with different numbers of diametrically polarized interference signals. It is shown that the higher-order modes possess strong polarization impurity, which may halve the available degrees-of-freedom for nulling in the presence of linear-polarized interferers, using a conventional null-steering algorithm. We verify the robustness of the designed compact receiver by means of a complete global-navigation-satellite-system demonstrator. It is shown that the maximum jammer power that is allowed us to maintain the CINR above 38 dBHz with three interferers can be improved by more than 10 dB if a decoupling and matching network is employed.

In this paper, the design of a broadband multi-layer microstrip antenna is presented. The broadband characteristics are the results of coupled resonances of the patch and transmission line through the resonant aperture. For this purpose, a cross-shaped transmission line, a ring slot, and a shaped ring patch are used. The simulation and measurement results indicate that a wide impedance bandwidth of 70% for |S11| < −10 dB and a perfect impedance matching 35% for |S11| < −20 dB are achieved. The gain is stable over the impedance bandwidth. The maximum gain of the proposed antenna is 8.8 dBi at 5 GHz. The radiation pattern, radiation efficiency, and cross-polarization are also suitable throughout the impedance bandwidth.

This paper presents a simple and compact coplanar waveguide (CPW)-fed circular-shaped reconfigurable patch antenna with a switchable circular polarization (CP) sense. The circular patch is cut at the ends vertically and switches are introduced to connect the patch ends. By controlling the ON/OFF status of the two switches, the polarization of the antenna can be switched between two states: left-hand circular polarization and right-hand circular polarization. The patch is designed on a very thin RT Duroid substrate of dielectric constant (εr) of 2.2 and thickness of 0.254 mm. The overall antenna dimensions are 35 × 30 mm. The antenna is designed and simulated using finite-element method -based EM simulator, HFSS. For each switching condition the return loss curve, radiation pattern are obtained. Axial ratio curves for polarization diversity cases are also plotted. Parametric studies have been made in order to get optimized values for certain antenna dimensions such as thickness, CPW ground to feed gap, etc.