Reconstructing the origin of bentonitic clays is often a challenging and rather complicated undertaking, but the analysis of certain predictor clay minerals is proving to be an excellent method to simplify this process. The goal of the present investigation was to use abundance changes of five X-ray diffraction (XRD) predictor minerals to determine the relative contributions of weathering and parent-rock changes to the origin of clay minerals in Egyptian bentonitic clays as the test case. The XRD predictor minerals, selected in an earlier discriminant function analysis of quantitative abundances of 14 minerals, provided a simpler approach to the interpretation of clay-mineral origins because they are the minerals that were most responsible for statistically significant differences among the samples. Changes in mineral composition were basically a function of parent-rock lithology, drainage, and climate interactions. A Paleo-Climate Index (CI; the ratio of coarsely crystalline kaolinite to Fe-rich smectite), and a Parent-Rock Index (PI; the ratio of the illitic phases and quartz abundances to pure smectite) were established to track the paleo-climate and parent-rock changes, respectively. Low CI values indicated that a long, seasonally dry climate prevailed during the Middle Eocene, uppermost Eocene, Lower Miocene, and Upper Pliocene bentonitic clay deposition. Lowermost Upper Eocene and the Middle Miocene bentonitic clays were produced when a wet climate prevailed throughout the year. Moderate to high PI values suggested derivation of the clays from the acidic basement crystalline rocks at Uweinat-Bir Safsaf uplift and Lower Paleogene shales during the Middle Eocene and lowermost Upper Eocene. The youngest Upper Eocene and Lower Miocene materials contained abundant Fe-smectite and low PIs indicating derivation from tholeiitic basalts. Diagenetic and sedimentary segregation modifications were not apparent. Direct evidence for in situ derivation from volcanic precursor materials was lacking in general, but volcanic eruptions were common in the region. The minerals in the Egyptian bentonitic clays formed as weathering products on land and have been transported by north-flowing streams and rivers to the sites of accumulation.

The crystal growth of NH4-illite (NH4-I) from the hydrothermal system of Harghita Bãi (Eastern Carpathians) was deduced from the shapes of crystal thickness distributions (CTDs). The <2 mm and the <2-0.2 mm fractions of clay samples collected from the argillized andesite rocks consist of NH4-illite-smectite (I-S) interstratified structures (R1, R2, and R3-type ordering) with a variable smectite-layer content. The NH4-I-S (40-5% S) structures were identified underground in a hydrothermal breccia structure, whereas the K-I/NH4-I mixtures were found at the deepest level sampled (-110 m). The percentage of smectite interlayers generally decreases with increasing depth in the deposit. This decrease in smectite content is related to the increase in degree of fracturing in the breccia structure and corresponds to a general increase in mean illite crystal thickness. In order to determine the thickness distributions of NH4-I crystals (fundamental illite particles) which make up the NH4-I-S interstratified structures and the NH4-I/K-I mixtures, 27 samples were saturated with Li and aqueous solutions of PVP-10 to remove swelling and then were analyzed by X-ray diffraction. The profiles for the mean crystallite thickness (Tmean) and crystallite thickness distribution (CTD) of NH4-I crystallites were determined by the Bertaut-Warren-Averbach method using the MudMaster computer code. The Tmean of NH4-I from NH4-I-S samples ranges from 3.4 to 7.8 nm. The Tmean measured for the NH4-I/K-I mixture phase ranges from 7.8 nm to 11.7 nm (NH4-I) and from 12.1 to 24.7 nm (K-I).

The CTD shapes of NH4-I fundamental particles are asymptotic and lognormal, whereas illites from NH4-I/K-I mixtures have bimodal shapes related to the presence of two lognormal-like CTDs corresponding to NH4-I and K-I.

The crystal-growth mechanism for NH4-I samples was simulated using the Galoper code. Reaction pathways for NH4-I crystal nucleation and growth could be determined for each sample by plotting their CTD parameters on an α-ß2 diagram constructed using Galoper. This analysis shows that NH4-I crystals underwent simultaneous nucleation and growth, followed by surface-controlled growth without simultaneous nucleation.

Excavated bentonite from two large iron-bentonite field experiments at Äspö Hard Rock Laboratory in Sweden was investigated with respect to iron redox chemistry and mineralogy. The iron redox chemistry was studied by Fe K-edge X-ray absorption near edge structure spectroscopy and the mineral phases were studied using X-ray diffraction. Bentonite is to be used as a buffer material in high-level radioactive waste repositories to protect the waste containers from their surroundings. Montmorillonite, which is responsible for the sealing properties in the bentonite, is susceptible to redox reactions. A change in the montmorillonite iron redox chemistry may affect its layer charge and hence its properties. The experiments included are the first Alternative Buffer Material test (ABM1) and the Temperature Buffer Test (TBT). The clays were heated to a maximum of ~130°C (ABM1) or ~150°C (TBT) for 2.5 and 7 y, respectively. In the central part of the compacted clay blocks was placed an iron heater and the distance from the heater to the rock was ~10 cm (ABM1) and ~50 cm (TBT), respectively. Eleven different clay materials were included in the ABM1 experiment and five were analyzed here. In the ABM1 experiment, the Fe(II)/Fe(III) ratio was increased in several samples from the vicinity of the heater. Kinetic data were collected and showed that most of the Fe(II)-rich samples oxidized rapidly when exposed to atmospheric oxygen. In the TBT experiment the corrosion products were dominated by Fe(III) and no significant increase in Fe(II) was seen. In ABM1, reducing conditions were achieved, at least in parts of the experiment; in TBT, reducing conditions were not achieved. The difference was attributed to the larger scale of the TBT experiment, providing more oxygen after the installation, and to the longer time taken for water saturation; oxidation of the samples during excavation cannot be ruled out. Minor changes in the bentonite mineral phases were found in some cases where direct contact was made with the iron heater but no significant impact on the bentonite performance in high-level radioactive waste applications was expected as a result.

Supercritical carbon dioxide (scCO2) processing has been proven as a method for preparing polymer/montmorillonite (MMT) nanocomposites with improved platelet dispersion. The influence of scCO2 processing on the shape and size of the MMT tactoid/platelet, which is of great importance to the final platelet dispersion in the polymer matrix, is scarcely reported in the literature. In the present study, the pristine MMT was first surface modified with 3-glycidoxypropyltrimethoxysilane (the grafted MMT is labeled as GMMT), and then intercalated using three kinds of intercalating agents, myristyltrimethyl-ammonium bromide (MTAB), tetradecyltrihexylphosphonium chloride (TDTHP), and ethoxyltriphenyl-phosphonium chloride (ETPC), in water or scCO2, to study the effect of intercalating agent type and intercalation method on the morphology and thermal properties of GMMT, as a part of a program devoted to the synthesis of polymer/MMT nanocomposites. The structure of intercalated GMMT was characterized by thermogravimetric analysis, X-ray powder diffraction, and scanning electron microscopy (SEM). The optimum intercalation conditions in scCO2 were established by trying a range of reaction times and pressures. The structures of intercalated GMMT obtained under optimum scCO2 conditions and water were compared. The basal spacing of GMMT intercalated in scCO2 was almost the same as that in water, and both were obviously larger than that of GMMT. The GMMT exhibited a compact spherical morphology (examined using SEM), and the surface structures (including surface morphology, surface roughness, and surface compactness) of samples intercalated in water became ‘less compact’ and the degree of the ‘compactness’ of samples intercalated in scCO2 decreased further. Whether in water or scCO2, samples intercalated with TDTHP exhibited a larger basal spacing and the extent of disorder increased compared to that for samples intercalated with MTAB. The pristine MMT was also intercalated for comparison and silane grafting was proven to contribute to the increased basal spacing and ‘less compact’ surface structure.