Rotor-stator flows are known to exhibit instabilities in the form of circular and spiral rolls. While the spirals are known to emanate from a supercritical Hopf bifurcation, the origin of the circular rolls is still unclear. In the present work we suggest a quantitative scenario for the circular rolls as a response of the system to external forcing. We consider two types of axisymmetric forcing: bulk forcing (based on the resolvent analysis) and boundary forcing using direct numerical simulation. Using the singular value decomposition of the resolvent operator the optimal response is shown to take the form of circular rolls. The linear gain curve shows strong amplification at non-zero frequencies following a pseudo-resonance mechanism. The optimal energy gain is found to scale exponentially with the Reynolds number $Re$ (for $Re$ based on the rotation rate and interdisc spacing $H$). The results for both types of forcing are compared with former experimental works and previous numerical studies. Our findings suggest that the circular rolls observed experimentally are the effect of the high forcing gain together with the roll-like form of the leading response of the linearised operator. For high enough Reynolds number it is possible to delineate between linear and nonlinear responses. For sufficiently strong forcing amplitudes, the nonlinear response is consistent with the self-sustained states found recently for the unforced problem. The onset of such non-trivial dynamics is shown to correspond in state space to a deterministic leaky attractor, as in other subcritical wall-bounded shear flows.

Low-frequency phenomena in an incompressible pressure-induced laminar separation bubble (LSB) on a flat plate is investigated using direct numerical simulation. The LSB configuration of Spalart and Strelets (J. Fluid Mech., vol. 403, 2000, pp. 329–349) is used. Wall pressure spectra indicate low-frequency-flapping $(St \sim 0.08)$ and high-frequency-shedding $(St \sim 1.52)$ regimes. Conditional velocity averages based on the fraction of reversed flow reveal the low frequency as an expansion/contraction of the LSB. While the high frequency only exhibits exponential growth within the LSB up to breakdown of the spanwise rollers, the low frequency and velocity fluctuations exhibit exponential growth upstream of separation. Instantaneous flow fields reveal large streamwise streaky structures forming within the LSB and extending past reattachment, much like high and low speed streaks in turbulent boundary layers. A predominance of sweep-like events ($Q4$) is observed during contraction and of ejection-like events ($Q2$) during expansion. These motions appear as dominant low-frequency modes in three-dimensional proper orthogonal and dynamic mode decompositions, exhibiting spatial amplification from separation to reattachment. The advection of a group of spanwise alternating streaky structures past the LSB results in an overall contraction after which the bubble expands to its ‘unforced’ state in the absence of the streaks. The low frequency then corresponds to the time it takes for streaks to form, amplify and advect past the LSB from separation to reattachment. This behaviour is linked to the mean flow deformation reported by Marxen and Rist (J. Fluid Mech., vol. 660, 2010, pp. 37–54), where the presence of streaks results in reduced mean bubble size. The formation of these streaky structures, in the absence of free stream turbulence, may be attributed to an absolute instability of the LSB due to the development of a secondary bubble within the primary.

Three-dimensional numerical simulations of hypersonic boundary layer transition delay due to porosity representative of carbon-fibre-reinforced carbon-matrix ceramics (C/C) were carried out on a 7$^{\circ {}}$ half-angle cone for unit Reynolds numbers $Re_m=2.43 \times 10^6$–$6.40\times 10^6\ \text {m}^{-1}$, at the free-stream Mach number $M_\infty =7.4$, for both sharp and 2.5 mm nose tip radii. A broadband time-domain impedance boundary condition was used to model the acoustic effects of the porous surface on the flow field. A quasi-spectral sub-filter-scale dynamic closure was adopted to stabilize the computations upon turbulent breakdown under extreme cooling conditions, with wall-to-adiabatic temperature ratio of $T_{w}/ T_{ad} \simeq 0.08 $, while accurately recovering the growth rates of the unstable modes present in the early transition stages. Good agreement is observed with the reference experimental data, both in terms of the predicted extent of the transition delay and the measured second-mode frequency spectrum. The latter is strongly modulated by the formation of near-wall low-temperature three-dimensional streaks. Pressure disturbances concentrate in corridors of locally thickened boundary layer, with frequencies lower than what predicted by linear theory. Here, trapped wavetrains are formed, which can persist long into the turbulent region. Finally, it is shown that the presence of a porous wall simply shifts the onset of turbulence downstream, without affecting its structure.

In this paper, we study the effect of lateral wall vibrations on the excitation and evolution of non-modal perturbations in hypersonic boundary layers subject to low-frequency freestream vortical disturbances (FSVDs). A novel, high-efficiency numerical approach, combining the harmonic weakly nonlinear Navier–Stokes and nonlinear parabolised stability equation approaches, is developed, which is sufficient to accommodate both the rapid distortion of the perturbation in the leading-edge vicinity and the nonlinear development of finite-amplitude high-order harmonics in the downstream region. The boundary-layer response to low-frequency FSVDs shows a longitudinal streaky structure, for which the temperature perturbation shows much greater magnitude than the streamwise velocity perturbation. The lateral vibration induces a Stokes layer solution for the spanwise velocity perturbation, which interacts with the FSVD-induced perturbations and leads to a suppression of the non-modal perturbation and an enhancement of the downstream modal perturbation. The new perturbations excited by the FSVD–vibration interaction strengthen as the vibration intensifies, and they could become comparable with the FSVD-induced perturbations in downstream locations at a high vibration intensity, indicating a remarkable modification of the streaky structure and its instability property. Secondary instability (SI) analyses based on the streaky base flow indicate that the vibration could enhance or suppress the SI modes, depending on their initial phases over the vibration period. Overall, the average effect is that the low-frequency and high-frequency SI modes are stabilised and destabilised by the vibration, respectively. Since the high-frequency SI modes undergo higher amplifications, the subsequent bypass transition is likely to be promoted by relatively strong vibrations.

The boundary-layer stability on a section of a rotating wind turbine blade with an FFA-W3 series aerofoil at a chord Reynolds number of $3 \times 10^5$, with varying rotation and radii, is studied with direct numerical simulations and linear stability analyses. Low rotation does not significantly affect transition in the outboard blade region. The relative insensitivity to rotation is due to a laminar separation bubble near the leading edge, spanwise-deformed by a primary self-excited instability, promoting the secondary absolute instability of the Kelvin–Helmholtz (KH) vortices and rapid transition. Moderate increases in rotation, or moving inboard, stabilise the flow by accelerating the attached boundary layer and possibly inducing competition between cross-flow and KH modes. This delays separation and transition. Initially, for high rotation rates or radial locations close to the hub, transition is delayed. Nevertheless, strong stationary and travelling cross-flow modes are eventually triggered, spanwise modulating the KH rolls and shifting the transition line close to the leading edge. Cross-flow velocities as high as $56\,\%$ of the free stream velocity directed towards the blade tip are reached at the transition location. For radial locations farther from the hub, the effective angle of attack is decreased, and cross-flow transition occurs at lower rotation rates. The advance or delay of the transition line compared with a non-rotating configuration depends on the competing rotation effects of stabilising the attached boundary layer and triggering cross-flow modes in the separation flow region.

Several transition scenarios are present in a hypersonic compression-ramp flow. In our previous work (Cao et al., J. Fluid Mech., vol. 941, 2022, p. A8), a complete transition process induced by the global instability of a compression-ramp flow was revealed. In a globally stable flow, however, the transition to turbulence can be promoted by convective instabilities, which is the focus of this work. The same flow conditions as in our previous work (Mach number 7.7, Reynolds number $8.6\times 10^5$ based on the flat-plate length) are considered here. Owing to a smaller ramp angle, a weakly separated flow forms on the compression ramp, which supports no global instability. Resolvent analysis identifies low-frequency streamwise streaks as the optimal response of base flow to upstream forcing. Local stability analysis reveals Mack's second mode in the boundary layer downstream of reattachment. By introducing random disturbances upstream of separation in direct numerical simulations, we observe breakdown to turbulence downstream of reattachment. Two transition scenarios are revealed, and they are highly dependent on the amplitude of upstream disturbances. For a large amplitude, strong streamwise streaks develop near the reattachment region, which break down to turbulence quickly. However, when the disturbance amplitude is reduced, the second-mode instability dominates the transition to turbulence.

Isolated-roughness-induced transitions controlled by local wall heating strips are studied via direct numerical simulation and BiGlobal linear stability analysis. The transition mechanisms are studied first with different wall temperatures. The separated shear layer–counter-rotating vortex system is found to be the main source for transitions. Symmetric and antisymmetric modes are observed in the wake, and the former is dominant. The local wall heating strip can delay the transition, and this effect is enhanced with higher heating temperature, wider strip and a combination of upstream and downstream control strips. The upstream strip lifts up the inlet flow and weakens the wake system in an indirect manner. The antisymmetric mode gradually vanishes, while the symmetric mode always exists but becomes weaker. The downstream strip exhibits a more effective transition delay by directly weakening the separated shear layer and vortex system in the wake. Vorticity transport analysis suggests that the downstream strip increases dissipation for streamwise vorticity and transfers it into wall-normal and spanwise vorticity. BiGlobal analyses indicate that the downstream strip shows less influence on the peak growth rate of the symmetric mode but significantly shrinks its unstable region. Analyses of the disturbance energy production indicate that the upstream strip wakens the wall-normal and spanwise shear at the same time, but the downstream strip mainly wakens the wall-normal one. More simulations are performed with different roughness heights, point-source disturbance and different roughness shapes. The results show that the current method remains effective enough in delaying transitions at a wide range of conditions.

This study explores precession-driven flows in a non-axisymmetric ellipsoid spinning around its medium axis. Using an experimental approach, we focus on two aspects of the flow: the base flow of uniform vorticity and the development of fluid instabilities. In contrast to a preceding paper (J. Fluid. Mech., vol. 932, 2022, A24), where the ellipsoid rotated around its shortest axis, we do not observe bi-stability or hysteresis of the base flow, but a continuous transition from small to large differential rotation and tilt of the fluid rotation axis. We then use the model developed by Noir & Cébron (J. Fluid. Mech., vol. 737, 2013, pp. 412–439) to numerically determine regions in the parameter space of axial and equatorial deformations for which bi-stability may exist. Concerning fluid instabilities, we use three independent observations to track the onset of both boundary layer and parametric instabilities. Our results clearly show the presence of a parametric instability, yet the exact nature of the underlying mechanism (conical shear layer instability, shear instability and elliptical instability) is not unambiguously identified. A coexisting boundary layer instability, although unlikely, cannot be ruled out based on our experimental data. To make further progress on this topic, a new generation of experiments at significantly lower Ekman numbers (ratio of rotation and viscous time scales) is clearly needed.

A novel selective mode decomposition, proper orthogonal decomposition and dynamic mode decomposition methods are used to analyse large-eddy simulation data of the flow field about a NACA0012 airfoil at low Reynolds numbers of $5\times 10^4$ and $9\times 10^4$, and at near-stall conditions. The objective of the analysis is to investigate the structure of the laminar separation bubble (LSB) and its associated low-frequency flow oscillation (LFO). It is shown that the flow field can be decomposed into three dominant flow modes: two low-frequency modes (LFO-Mode-1 and LFO-Mode-2) that govern an interplay of a triad of vortices and sustain the LFO phenomenon, and a high-frequency oscillating (HFO) mode featuring travelling Kelvin–Helmholtz waves along the wake of the airfoil. The structure and dynamics of the LSB depend on the energy content of these three dominant flow modes. At angles of attack lower than the stall angle of attack and above the angle of a full stall, the flow is dominated by the HFO mode. At angles of attack above the stall angle of attack the LFO-Mode-2 overtakes the HFO mode, triggers instability in the LSB and initiates the LFO phenomenon. Previous studies peg the structure, stability and bursting conditions of the separation bubble to local flow parameters. However, the amplitude of these local flow parameters is dependent on the energy content of the three dominant flow modes. Thus, the present work proposes a more robust bursting criterion that is based on global eigenmodes.

We perform a detailed numerical study of modal and non-modal stability in oblique Couette–Poiseuille profiles, which are among the simplest examples of three-dimensional boundary layers. Through a comparison with the Orr–Sommerfeld operator for the aligned case, we show how an effective wall speed succinctly characterizes modal stability. Large-scale parameter sweeps reveal that the misalignment between the pressure gradient and wall motion is, in general, destabilizing. For flows that are sufficiently oblique, the instability is found to depend exclusively on the direction of wall motion and not on its speed, a conclusion supported, in part, by the perturbation energy budget and the evolution of the critical layers. Closed forms for the critical parameters in this regime are derived using a simple analysis. From a non-modal perspective, pseudoresonance is examined through the resolvent and the $\epsilon$-pseudospectra. An analysis of the unforced initial value problem shows that the maximum energy gain is highly dependent on both the magnitude and direction of the wall velocity. However, the strongest amplification is always achieved for configurations that are only weakly skewed. Finally, the optimal perturbations appear to develop via a lift-up effect enhanced by an Orr-like mechanism, the latter driven by cross-flow shear.

We investigated the effects of two-dimensional sharp-edged rectangular bumps on Tollmien–Schlichting (TS) wave evolution using direct numerical simulation. The bump height, $h$, ranged from 5 % to 40 % of the local displacement thickness, $\delta ^*$. Behind the bump, a recirculating flow region could be formed whose length increased nonlinearly with $h$. The bump height effect on the TS wave, which was the dominant, scaled super-exponentially with $h$. We also showed a substantial effect of the $\delta ^*$-based Reynolds number, ${\textit {Re}} _{\delta ^*}$. Firstly, the bump wake extended with ${\textit {Re}} _{\delta ^*}$, promoting larger TS wave growth rates. The second effect is related to proximity to the upper branch of the instability loop, accounting for the influence of the TS frequency, as well. It dictates the bump impact increases as it gets closer to transition, either by the bump moving downstream or the transition moving upstream. For a 40 % high bump, for example, changing the ${\textit {Re}} _{\delta ^*}$ at the bump location from 1500 to 2000 increased $\Delta N$ by a factor of 2 ($\Delta N$ represents a measure of a surface irregularity effect on the smooth plate N-factor). We also found that $(\Delta N)_{max}$ increases linearly with ${\textit {Re}} _{hh}$. Results in the subsonic regime showed that the bump impact attenuates with Mach number up to 0.7 but above it, stabilisation is surpassed by the destabilising effect caused by the recirculation lengthening. This is mostly associated with the bump wake that extends with the pressure gradient which increases substantially towards the sonic speed. This is enhanced if the surface is adiabatic rather than isothermal.

The free-stream turbulence (FST) induced transition in perfect and non-ideal gas zero-pressure-gradient flat-plate boundary layers is investigated by means of large-eddy simulations. The study focuses on the influence of large incoming disturbances over the laminar-to-turbulent transition, by comparing two different integral length scales $L_f$, which differ by a factor of seven, at different FST intensities $T_u$. High-subsonic dense-gas boundary layers of the organic vapour Novec649, representative of organic Rankine cycle applications, are compared with air flows at Mach numbers 0.1 and 0.9. Compressibility and non-ideal gas effects are shown to be of minor importance in comparison to the influence of the FST integral length scale $L_f$. An increase of the inlet turbulent intensity always promotes transition, whereas an increase of $L_f$ has a double effect on the transition onset. At $T_u=2.5\,\%$, increasing $L_f$ promotes the transition, while it tends to delay transition for an FST intensity of 4 %. Larger FST integral scales tend to increase the spanwise distance between laminar streaks generated in the boundary layer. Two competing transition scenarios are observed. When the incoming turbulence intensity and length scale are moderate, the classical bypass route consists in the linear non-modal growth of streaks, which then experience secondary instabilities (sinuous or varicose) and lead to the generation of turbulent spots. The second scenario is characterized by the appearance of $\Lambda$-shaped structures near the inlet, which are further stretched to hairpin vortices before breaking down to turbulence. Spot inceptions can therefore occur at earlier locations than the streak growth. We are then faced with a competition between the classical bypass transition and nonlinear response mechanisms that ‘bypass’ this route. The present case at high $L_f$ and low $T_u$ is an example of a competing scenario, but even for the higher $T_u$ and $L_f$ conditions, only approximately one-third of turbulent spots are due to the $\Lambda$-shaped events. The nonlinear alternative route has strong similarities with scenarios described previously in the literature in the presence of leading edge effects or due to passing wakes. Such a path is governed by the turbulence intensity, but also by the integral length scale, with both parameters playing a critical role in the generation of the $\Lambda$-shaped structures near the inlet. This alternative mechanism is found to be robust under varying flow and thermodynamic conditions.

It is well known that buoyancy suppresses, and can even laminarise, turbulence in upward heated pipe flow. Heat transfer seriously deteriorates in this case. A new direct numerical simulation model is established to simulate flow-dependent heat transfer in an upward heated pipe. The model shows good agreement with experimental results. Three flow states are simulated for different values of the buoyancy parameter $C$: shear turbulence, laminarisation and convective turbulence. The latter two regimes correspond to the heat transfer deterioration regime and the heat transfer recovery regime, respectively (Jackson & Li 2002; Bae et al., Phys. Fluids, vol. 17, issue 10, 2005; Zhang et al., Appl. Energy, vol. 269, 2020, 114962). We confirm that convective turbulence is driven by a linear instability (Su & Chung, J. Fluid Mech., vol. 422, 2000, pp. 141–166) and that the deteriorated heat transfer within convective turbulence is related to a lack of rolls near the wall, which leads to weak mixing between the flow near the wall and the centre of the pipe. Having surveyed the fundamental properties of the system, we perform a nonlinear non-modal stability analysis, which seeks the minimal perturbation that triggers a transition from the laminar state. Given the differences between shear and convective turbulence, we aim to determine how the nonlinear optimal (NLOP) changes as the buoyancy parameter $C$ increases. We find that at first, the NLOP becomes thinner and closer to the wall. Most importantly, the critical initial energy $E_0$ required to trigger turbulence keeps increasing, implying that attempts to trigger it artificially may not be an efficient means to improve heat transfer at larger $C$. At $C=6$, a new type of NLOP is discovered, capable of triggering convective turbulence from lower energy, but over a longer time. It is active only in the centre of the pipe. We next compare the transition processes, from linear instability and by the nonlinear non-modal excitation. At $C=4$, linear instability leads to a state that approaches a travelling wave solution or periodic solutions, while the minimal seed triggers shear turbulence before decaying to convective turbulence. Deeper into the parameter space for convective turbulence, at $C=6$, the new nonlinear optimal triggers convective turbulence directly. Detailed analysis of the periodic solution at $C=4$ reveals three stages: growth of the unstable eigenfunction, the formation of streaks, and the decay of the streaks. The stages of the cycle correspond to changes in the linear instability of the turbulent mean velocity profile. Unlike the self-sustaining process for classical shear flows, where the streak is disrupted via instability, here, decay of the streak is more closely linked to suppression of the linear instability of the mean flow, and hence suppression of the rolls. Flow visualisations at $C$ up to $10$ also show similar processes, suggesting that the convective turbulence in the heat transfer recovery regime is sustained by these three typical processes.

We investigate the dynamics of a columnar Taylor–Green vortex array under strong stratification, focusing on Froude numbers $0.125\leq Fr \leq 1.0$, with the aim of identifying and understanding the primary instabilities that lead to the vortices’ breakdown. Linear stability analysis reveals that the fastest-growing vertical wavenumber scales with $Fr^{-1}$, while the dimensionless growth rate remains approximately constant. The most unstable eigenmode, identified as the mixed hyperbolic mode by Hattori et al. (J. Fluid Mech., vol. 909, 2021, A4), bears significant similarities to the zigzag instability, first discovered by Billant & Chomaz (J. Fluid Mech., vol. 418, 2000, pp. 167–188). Direct numerical simulations further confirm that the zigzag instability is crucial in amplifying initial random perturbations to finite amplitude, with the flow structure and modal growth rate consistent with the linear stability analysis. In particular, the characteristic vertical length scale of turbulence matches that of the fastest-growing linear mode. These findings underscore the broader relevance of the zigzag instability mechanism beyond its initial discovery in vortex pairs, demonstrating its role in facilitating direct energy transfer from vertically uniform vortical motions to a characteristic vertical length scale proportional to $Fr$ in strongly stratified flows.

Linear stability analysis currently fails to predict turbulence transition in canonical viscous flows. We show that two alternative models of the boundary condition for incipient perturbations at solid walls produce linear instabilities that could be sufficient to explain turbulence transition. In many cases, the near-wall behaviour of the discovered instabilities is empirically indistinguishable from the classical no-slip condition. The ability of these alternative boundary conditions to predict linear instabilities that are consistent with turbulence transition suggests that the no-slip condition may be an overly simplified model of fluid–solid interface physics, particularly as a description of the flow perturbations that lead to turbulence transition in wall-bounded flows.

Numerous studies have indicated that turbulence typically initiates along the boundary layer of the stationary disk within a rotor–stator cavity. To describe the transition process to turbulence on the stationary side of a closed rotor–stator cavity, a comprehensive approach combining global linear stability analysis with direct numerical simulation was adopted in the present study. The proposed model aligns with that of Yim et al. (J. Fluid Mech., vol. 848, 2018, pp. 631–647), who investigated the stability characteristics of the rotating-disk boundary layer in a rotor–stator cavity. In order to achieve a stable inflow for the stationary-disk boundary layer, we rotate the shroud together with the rotating disk. Through careful global stability analysis, the predominant spiral mode exhibiting the highest instability in the boundary layer of the stationary disk was discerned, corroborating observations from simulations. Initially, the spiral mode undergoes linear amplification, reaches a state of linear saturation and enters the nonlinear regime. Following nonlinear saturation in the flow field, a circular wave mode arises due to the influence of mean flow distortion. As the Reynolds number attained a sufficiently high level, the interplay between the downstream-propagating circular mode and spiral mode amplified disturbances in the boundary layer of the stationary disk, ultimately leading to the development of localised turbulence at the mid-radius of the rotor–stator cavity. Notably, the present study is the first to elucidate the coexistence of laminar–transitional–turbulent flow states in the stationary-disk boundary layer through direct numerical simulations.

Direct numerical simulations (DNS) were carried out to investigate flow control for transition delay using steady blowing/suction strips at the wall of a flared cone at Mach 6 and zero angle of attack. For the numerical investigations of the transition control strategy, the flared cone geometry and the flow conditions of the experiments in the Boeing/Air Force Office of Scientific Research (AFOSR) Mach 6 Quiet Tunnel (BAM6QT) at Purdue University were chosen. For the DNS, transition was initiated by introducing random disturbances at the inflow of the computational domain, emulating ‘natural’ transition in wind-tunnel experiments caused by free-stream noise. In both wind-tunnel experiments and numerical simulations, streamwise ‘hot’ streaks were found on the surface of the flared cone, which are caused by a nonlinear interaction of an axisymmetric second-mode wave and a pair of oblique waves of the same frequency (‘fundamental resonance’). The objective of the flow control strategy proposed here is to delay the transition onset, and thus mitigate the negative consequences associated with the nonlinear transition stages, i.e. the development of hot streaks and large wall-pressure amplitudes that were observed in experiments and DNS. Our previous so-called ‘controlled’ transition simulations have shown that flow control using steady blowing and suction strips can lead to a significant delay of the hot streak development on the surface of the flared cone. The simulation results presented in this paper show that this flow control strategy remains effective, even in a natural transition scenario characterized by broadband disturbances.

Numerical simulations of thermoelectrohydrodynamic convection in a dielectric liquid inside a finite-length cylindrical annulus with a fixed temperature difference have been performed with increasing high-frequency electric tension under microgravity conditions. The electric field, coupled with the permittivity gradient, generates a dielectrophoretic buoyancy force whose non-conservative part can induce thermoelectric convection in the liquid. The liquid remains in a conductive state below a critical value of the applied electric voltage. At a critical value, a supercritical bifurcation occurs from the conductive state to a convective state made of stationary helicoidal vortices. A further increase of electric voltage leads to oscillatory helicoidal vortices and then to wavy patterns before spoke patterns dominate the convective flow. The dielectrophoretic force is shown to enhance the heat transfer from the hot to cold walls due to induced convective flows. Particularly, these results demonstrate that the dielectrophoretic buoyancy force holds promise to replace the gravitational force to induce efficient heat transfer in microgravity conditions, and they contribute to a better fundamental understanding of heat transfer in microgravity.

The efficacy of steady large-amplitude blowing/suction on instability and transition control for a hypersonic flat plate boundary layer with Mach number 5.86 is investigated systematically. The influence of the blowing/suction flux and amplitude on instability is examined through direct numerical simulation and resolvent analysis. When a relatively small flux is used, the two-dimensional instability critical frequency that distinguishes the promotion/suppression mode effect closely aligns with the synchronisation frequency. For the oblique wave, as the spanwise wavenumber increases, the suppression effects would become weaker and the mode suppression bandwidth diminishes/increases in general in the blowing/suction control. Increasing the blowing/suction flux can effectively broaden the frequency bandwidth of disturbance suppression. The influence of amplitude on disturbance suppression is weak in a scenario of constant flux. To gain a deeper insight into disturbance suppression mechanism, momentum potential theory (MPT) and kinetic energy budget analysis are further employed in analysing disturbance evolution with and without control. When the disturbance is suppressed, the blowing induces the transport of certain acoustic components along the compression wave out of the boundary layer, whereas the suction does not. The velocity fluctuations are derived from the momentum fluctuations of the MPT. Compared with the momentum fluctuations, the evolutions indicated by each component's velocity fluctuations greatly facilitate the investigations of the acoustic nature of the second mode. The rapid variation of disturbance amplitude near the blowing is caused by the oscillations of the acoustic component and phase speed differences between vortical and thermal components. Kinetic energy budget analysis is performed to address the non-parallel effect of the boundary layer introduced by blowing/suction, which tends to suppress disturbances near the blowing. Moreover, viscous effects leading to energy dissipation are identified to be stronger in regions where the boundary layer is rapidly thickening. Finally, it is demonstrated that a flat plate boundary layer transition triggered by a random disturbance can be delayed by a blowing/suction combination control. The resolvent analysis further demonstrates that disturbances with frequencies that dominate the early transition stage are dampened in the controlled base flow.

We study the stability of a zero-pressure gradient boundary layer subjected to free-stream disturbances by means of local stability analysis. The dataset under study corresponds to a direct numerical simulation (DNS) of a flat plate with a sharp leading edge in realistic wind tunnel conditions, with a turbulence level of 3.45 % at the leading edge. We present a method to track the convective evolution of the secondary instabilities of streaks by performing sequential stability calculations following the wave packet, connecting successive unstable eigenfunctions. A scattered nature, in time and space, of secondary instabilities is seen in the stability calculations. These instabilities can be detected before they reach finite amplitude in the DNS, preceding the nucleation of turbulent spots, and whose appearance is well correlated to the transition onset. This represents further evidence regarding the relevance of secondary instabilities of streaks in the bypass transition in realistic flow conditions. Consistent with the spatio-temporal nature of this problem, our approach allows us to integrate directly the local growth rates to obtain the spatial amplification ratio of the individual instabilities, where it is shown that instabilities reaching an $N$-factor in the range [2.5,4] can be directly correlated to more than 65 % of the nucleation events. Interestingly, it is found that high amplification is not only attained by modes with high growth rates, but also by instabilities with sustained low growth rates for a long time.