This paper presents a methodology designed to leverage multitemporal sequences of synthetic aperture radar (SAR) and multispectral data and automatically extract urban changes. The approach compares results using different radar and optical sensors, describing the advantages and drawbacks of using SAR data from the COnstellation of small Satellites for the Mediterranean basin Observation (COSMO)/SkyMed, SAtélite Argentino de Observación COn Microondas (SAOCOM), and Sentinel-1 constellations, as well as nighttime light data or Sentinel-2 images. Multiple indexes obtained from multispectral data are compared, too, and results obtained by an unsupervised clustering procedure are analyzed. The results show that using different datasets it is possible to obtain consistent results about different types of changes in urban areas (e.g., demolition, development, and densification) with different levels of spatial details.

Adrenal gland-induced hypertension, also known as secondary hypertension, is a medical condition caused by an underlying adrenal pathology, most typically adrenocortical adenomas. Current clinical practices involve pharmacotherapy or surgical resection to treat adrenal gland diseases that cause hypertension. However, due to the limitations of these treatment options, microwave ablation (MWA) has emerged as a promising minimally invasive alternative. An accurate understanding of the dielectric properties of adrenal glands would support the further development and optimization of MWA technology for treating adrenal tumors. Only a few studies have examined the dielectric properties of both human and animal adrenal glands, and the sample sizes of these studies have been relatively small. Therefore, further dielectric data of human and animal adrenal glands are warranted. This paper presents the ex vivo dielectric properties of the ovine adrenal glands (medulla and cortex) and summarizes the published literature on dielectric data of adrenal glands from porcine, bovine, ovine, and human samples in the microwave frequency range to analyze the consistency and reliability of the reported data. The dielectric properties of the ovine adrenal glands (N = 8) were measured using an open-ended coaxial probe measurement technique at frequencies ranging from 0.5 to 8.5 GHz. This study also investigated the temperature-dependent dielectric properties of the ovine adrenal medulla ranging from 37 to 64°C at frequencies ranging from 0.5 to 8.5 GHz. The dielectric properties of the ovine adrenal medulla measured in this study were found to be consistent with the literature. Moreover, the review suggests that variations exist in the dielectric properties of the adrenal medulla and cortex among species. The study also found that the dielectric properties of the adrenal medulla decrease with increasing temperature, similar to other tissues for which temperature-dependent dielectric data have been reported. This summary of dielectric data of adrenal glands and the temperature-dependent dielectric properties of the ovine adrenal medulla will accelerate the development of MWA technologies for hypertension treatment.

In this study, a novel, cost-effective miniaturized tag antenna was developed for applications on the human body. To achieve impedance matching with the complex conjugate impedance of the Monza-4 tag chip (7.17–j74.22 Ω at 915 MHz), the proposed structure was configured by coarsely tuning the positions of vias and fine-tuning the small gaps of its coupled patches. For further reducing the profile and dimensions of the antenna, a design technique based on the three-dimensional dipole antenna current distribution was used. The proposed antenna configuration was not only miniaturized but also achieved a long stable reading distance (>5.0 m) and a wide impedance bandwidth of 71 MHz or 7.65% (covering the ultrahigh frequency radio frequency identification ranges in most regions), regardless of the location of the tag on the human body. Experiments were conducted to validate the simulated results, and adequate agreement was found between the simulated results and the measured results.

Radar-based hand gesture recognition is a potential noncontact human–machine interaction technique. To enhance the recognition performance of hand gesture, a multidomain fusion-based recognition method using frequency-modulated continuous wave radar is proposed in this article. The received raw echo data of gestures is preprocessed to obtain the range–time matrix, Doppler–time matrix, and range–Doppler–frame tensor. The obtained three-domain radar data corresponding to each gesture are input into the three-channel convolutional neural network for feature extraction. In particular, the extracted features from three-domain data are fused with learnable weight matrices to obtain the final gesture classification results. The experimental results have shown that the classification accuracy of the proposed multidomain fusion network based on learning weight matrix-based fusion is 98.45%, which improves the classification performance compared with the classic average-based fusion and concatenation fusion.

The main interest in using synthetic aperture radar (SAR) technology in automotive scenarios is that arbitrarily long arrays can be synthesized by exploiting the natural motion of the ego vehicle, enabling finer azimuth resolution and improved detection. All of this is achieved without increasing the hardware complexity in terms of the number of physical antennas. In this paper, we start by discussing the application of SAR imaging in the automotive environment from both theoretical and experimental perspectives. We proceed by describing an efficient processing workflow and we derive the rough number of operations required to focus an image proving the real-time imaging capability of the system. The experimental results are based on open road data acquired using an eight-channel radar at 77 GHz, considering side-looking SAR and forward SAR. The results confirm the idea that SAR imaging can be successfully and routinely used for high-resolution mapping of urban environments in the near future.

This paper proposes a triple-band fractal slot antenna with enhanced gain operating at frequencies of 2.7, 3.5, and 4.8 GHz for microwave wireless power transmission. The antenna achieved more than 3 dB gain by preserving the symmetrical defected reflector structure behind it at a length of 0.54λ/4, where λ is the wavelength in free space at 2.7 GHz. A 50 Ω micro-strip line coupled at 66 mm length helps feed the triple band slot antenna. The purpose of a triple-band rectifier circuit with an impedance network is to convert the radio frequency (RF) signal into direct current. The measurements reveal that the antenna’s enhanced gain is 8.8 dB, and the rectifier’s highest RF signal to direct current conversion efficiency is 74.3%. For the combined configuration unit of measure, the antenna is assimilated into the rectifier via back-to-back 50 Ω Sub Miniature Version A (SMA) connectors. The highest recorded efficiency of 49.67% was obtained for the rectenna at optimum values of 1 kΩ resistive load and −5 dBm power input. It has been revealed that the rectifier-integrated antenna presented is effective for low-input RF energy capture and power transmission.

This article presents the design of a novel sigma slotted circular monopole antenna for wireless body area network applications. The design is proceeded with a sigma-shaped slot etched on the circular radiator with Rogers 4003C substrate. The size of the proposed antenna is 30 × 30 × 1 mm3. With partial ground plane, the bandwidth characteristics of the antenna have been enhanced. The designed antenna covers 2–10 GHz of the ultra wideband, thereby providing more than 106% bandwidth. The antenna exhibits high gain values of 1.95, 3.23, 3.46, and 5.95 dB at 2.45, 3.45, 5.8, and 9.5 GHz, respectively. The proposed design operates on off-body mode at 2.45 GHz and on-body mode at 5.8 GHz, thus acting as a dual-mode antenna. To ensure the health and safety measure, specific absorption rate analysis was done for both low and high values of input power and also with Cartesian and cylindrical human arm models. Bending analysis was also done. The time domain parameter group delay was also analyzed for the proposed antenna for on- and off-body scenarios. The prototype was fabricated, and validation of simulation results was done for free space and on-body scenarios.

In this paper, a mode-matching procedure is used to prove for the first time the dispersionless behavior of glide symmetry (GS) in corrugated metasurface waveguides. Depending on their field symmetry, the Floquet harmonics have a different impact onto the frequency dispersion, which is reduced with GS when the gap between the surfaces is small. Indeed, the glide-symmetric waveguide is shown to have the same effective propagation features as a scaled mirror-symmetric waveguide with half the period and a doubled gap. We propose closed-form formulas for the effective refractive index of the glide-symmetric waveguide in the first Brillouin zone, having a small groove compared to the period. The closed-form expressions analytically prove the dispersionless behavior of GS.

This paper investigates the performance of 3D-printed dielectric reflectarray antennas (RAs) with wideband behavior and beam-steering capabilities. The designed unit cell consists of a single-layer dielectric element perforated with a square hole, whose side is used to control the local variation of the reflection coefficient. The numerical analysis of the unit cell and of first $52\times52$ reflectarray working in Ka-band, whose scanning capabilities are tested just moving the feed along an arc, confirms that the unit cell has a stable behavior with respect to both the frequency and the direction of arrival of the incident field. In view of these promising capabilities, the proposed unit cell is used to design a bifocal reflectarray with the same size and working in the same frequency band of the first one. Its numerical characterization and the measurements of a prototype prove that the RA is able to provide less than 0.8 dB of gain losses over a scanning range of ±40∘ in the vertical plane, while the bandwidth varies between 13.5% and 28%, depending on the pointing direction. The obtained results demonstrate the effectiveness of the proposed approach and highlight the potential of 3D-printing technology for producing high performance, cost-effective RAs with wideband behavior and excellent beam-steering features.

Wireless power transfer (WPT) is an emerging technology with many promising applications where transmitting power via wired connections is undesirable. However, near-field WPT between magnetically coupled inductors is highly susceptible to positional changes, with power transfer efficiency (PTE) suffering if the coils are misaligned. To combat this effect, many position-independent, self-adaptive, inductive WPT schemes have been developed. Recent work indicates that it is possible to passively achieve high PTE across the operating range with nonlinear capacitors. In this work, the functionality of nonlinear WPT circuits is investigated, and fundamental design equations are derived and validated. A simplified design procedure is proposed for the position-independent self-adaptive WPT using nonlinear capacitors, wherein the ideal capacitance is extracted for each coupling factor. The efficacy of the method is demonstrated with an experimental circuit. Future work in this area is also proposed.

This research work presents an implantable antenna that operates at 5.8 GHz. By using a radiator with a loop-based design, the antenna can be made smaller. Radiator is made up of three connected rectangular loops. On the substrate’s back side, an I-shaped ground plane is used. As substrate and superstrate, polydimethylsiloxane (PDMS) with dimensions of 7 mm × 5 mm × 0.3 mm is used. The conducting sections are made using copper foil that is 30 µm thick. The suggested antenna is examined by the implantable medical device using realistic human scalp phantom models and a homogenous skin box. Simulated study revealed that it operates around 5.8 GHz with a bandwidth from 5.69 to 5.92 GHz. The specific absorption rate was 0.28 and 0.26 W/kg for skin box and human scalp phantoms, respectively, at 1 mW input power across 1 g volume tissue.

An E-band Cassegrain switched beam high-gain antenna concept for 5G backhauling systems is proposed in this article. The antenna requirements target the compensation of small misalignments (within ±1 degrees in both azimuth and elevation planes) in E-band backhauling links due to adverse weather conditions or thermal deformations. The intended antenna is able to realize beam-switching operations by using a feed-array architecture based on a 7 × 7 array of cavity-backed magnetoelectric (ME) dipoles, where every element is capable of providing a steering of ±0.33 degrees in both the elevation and the azimuth planes. The ME dipole illuminators combined with a Cassegrain reflector provide a gain of 52 dBi within the whole scanning range. Besides, they can be easily integrable with the front-end modules, thus being an easily implementable and low-cost alternative to other more complex solutions based on horns or lens antennas.

In this study, tunability of the electromagnetically induced transparency (EIT)-like transmission window by low-volume dielectric loadings is presented both numerically and experimentally in S-band. The EIT-like transmission behavior is obtained by a metamaterial, composed of an electric resonator and a closed-ring resonator patterned on a dielectric substrate. The frequency tuning is obtained by two applications called horizontal sliding application (HSA) and vertical sliding application based on sliding of the low-volume loadings from the edges to geometric center (i.e., inward). For both applications, the frequency tuning has been investigated for dielectric loadings which have relative permittivity of 2.2, 3, 4.5, and 6.15. The results reveal that the proposed sliding applications are effective on tuning the transmission peak frequency. An achieved 1136 and 971 MHz absolute spectral shifts and corresponding 6.34% and 5.41% absolute sensitivities by simulations and measurements, respectively, are the best results which are obtained for HSA at 5 mm shift value. Moreover, 14.67% sensitivity is obtained in simulations for the complete dielectric loading on the resonator in response to the increase in refractive index from 1 to 1.5. It is believed that the proposed applications will contribute to the existent sensing studies.

An absorptive reconfigurable bandstop filter (BSF) with compact size and ultra-wide frequency tuning range using distributed lossy resonators is presented. In each reconfigurable bandstop resonator, a varactor and a PIN diode are utilized as the control and absorption devices. When the PIN diodes are in off and on states, the upper and lower frequency tuning ranges of stopbands can be obtained, respectively. Therefore, the ultra-wide total frequency tuning range which is the combination of the upper and lower frequency tuning ranges can be realized. Meanwhile, the stopband frequency and bandwidth tuning can be independently controlled by bias voltages. The resistances in the varactors and PIN diodes can dissipate the electromagnetic power and thus result in absorptive stopband without using extra absorptive circuits. The stopband suppression level and stopband absorption ratio are proportional to the number of distributed lossy resonators. For demonstration, an absorptive reconfigurable BSF prototype using six pairs of distributed lossy resonators is designed and fabricated. The measured total frequency tuning range is 3.03–6.39 GHz (71%) with the suppression level of 20 dB, while the frequency tuning range with the suppression level of 10 dB is 2.04–6.39 GHz (103%).

With the rapid development of communication technology, the researches of multi-band filtering circuits have become more and more important. Multimode resonator (MMR) is one of the vital methods to provide multi-resonant modes within a single design. In this paper, a dual-band ultra-wideband bandpass filter (UWB-BPF) using stepped impedance stub-loaded resonators (SI-SLR) is presented. The main advantage of using SI-SLR is to have better performance with multimode behavior and more parameters to control resonant modes. SI-SLR combines the advantages of SIR and SLR structures, which gives a compact, high-performance multiband filter. The proposed filter design has compact size, sharp and flat response with low insertion loss (IL), low return loss (RL), and high band-to-band rejection. The filter is designed for UWB communication in wireless body area networks and fabricated on Arlon substrate with relative permittivity ${\varepsilon_{\textrm{r}}} = 3.25$, thickness $0.8\;{\textrm{mm}}$. The resulted dual-bands are centered at $4{\textrm{ GHz}}$ and $8.3{\textrm{ GHz}}$ with fractional bandwidths $37{\textrm{% }}$ and $48{\textrm{%}}$. The simulation was carried out using CST Microwave Studio. The filter provides good passband performances, with IL 0.49 dB and 0.31 dB at the center frequency of lower and higher bands, respectively. The band-to-band 40 dB rejection is realized by adding circular spiral at the input/output of the filter.

By combining the technique of energy selective surface and frequency selective rasorber, an energy selective rasorber is proposed, which performs selective energy protection in the low communication frequency band (0.8–2 GHz) and wave-absorbing property in the high-frequency band (6–18 GHz). The design consists of two layers, of which the bottom one contains a lumped diode structure for energy selection function in the transmission band, while together with the top layer, they perform a wideband wave absorbing function. The simulated and measured results agree well with each other, and both show good absorption in 6–18 GHz and energy-selective property around 1.86 GHz. That is, when the incident power changes from −30 to 14 dBm, the reflection coefficient changes from below −22 dB to above −2 dB, while the transmission coefficient changes from above −3 dB to below −17 dB.

A wideband antipodal Vivaldi antenna has been designed and optimized. A slight improvement is obtained by employing multiple metalense based on circular split-ring resonators to maximize the antenna gain with the maximum bandwidth. The designed antennas have been fabricated and characterized, showing good agreement with simulations. The maximum measured gain is $G = 12\;{\textrm{dB}}$, and the −10 dB bandwidth is from $f = 3\;{\textrm{GHz}}$ to $f = 13\;{\textrm{GHz}}$.

In [A. Capozzoli, C. Curcio, A. Liseno, MMS, Pizzo Calabro, Italy, 2022], the problem of modeling a source/scatterer using an equivalent radiator has been addressed and an approach has been given and numerically assessed.

Once dimensioned the radiating panel, a practical implementation can be provided by a non-uniform array. The element positions should be chosen so that the array is capable to approximate, with an adequate accuracy, the fields radiated by the equivalent radiator. Here, the array element positioning is performed by exploiting a quadrature rule which takes into account that the singular functions supported on the region of interest associated to the most significant singular values of the radiation operator are related to those supported on the equivalent panel by a radiation integral. The quadrature rule enables also to choose a set of weights which are essential in the definition of the element excitation coefficients from the knowledge of the source distribution on the equivalent panel. For simplicity, a one-dimensional problem with a Legendre quadrature rule is considered. The approach is numerically assessed by checking the capability of the array to radiate, with a satisfactory degree of accuracy, the singular functions associated to the region of interest.

A low-profile wideband circularly polarized (CP) metasurface antenna is demonstrated for C-band applications. The metasurface consists of 4 × 4 square patches with Z-shaped slots. Characteristic mode analysis is used to investigate the modal behavior of the metasurface, and a pair of degenerate modes is chosen as the operating modes. The CP radiation is realized by exciting a pair of degenerate modes of the metasurface through a slot antenna, which is used as a feed structure with a 90° phase difference. The CP bandwidth is further widened by combining the resonance modes of the metasurface and slot antenna. The measured results show that the −10 dB impedance bandwidth of the antenna is 3.47–4.76 GHz, and the 3 dB axial ratio bandwidth is 3.5–4.9 GHz with a peak gain of 6.9 dBic. Moreover, the antenna exhibits well left-hand CP radiation performances with a low profile of 0.046λ0.