Snake robots can move flexibly due to their special bodies and gaits. However, it is difficult to plan their motion in multi-obstacle environments due to their complex models. To solve this problem, this work investigates a reinforcement learning-based motion planning method. To plan feasible paths, together with a modified deep Q-learning algorithm, a Floyd-moving average algorithm is proposed to ensure smoothness and adaptability of paths for snake robots’ passing. An improved path integral algorithm is used to work out gait parameters to control snake robots to move along the planned paths. To speed up the training of parameters, a strategy combining serial training, parallel training, and experience replaying modules is designed. Moreover, we have designed a motion planning framework consists of path planning, path smoothing, and motion planning. Various simulations are conducted to validate the effectiveness of the proposed algorithms.

As the proportion of the elderly population in the USA expands, so will the demand for rehabilitation and social care, which play an important role in maintaining function and mediating motor and cognitive decline in older adults. The use of social robotics and telemedicine are each potential solutions but each have limitations. To address challenges with classical telemedicine for rehabilitation, we propose to use a social robot-augmented telepresence (SRAT), Flo, which was deployed for long-term use in a community-based rehabilitation facility catering to older adults. Our goals were to explore how clinicians and patients would use and respond to the robot during rehab interactions. In this pilot study, three clinicians were recruited and asked to rate usability after receiving training for operating the robot and two of them conducted multiple rehab interactions with their patients using the robot (eleven patients with cognitive impairment and/or motor impairment and 23 rehab sessions delivered via SRAT in total). We report on the experience of both therapists and patients after the interactions.

This paper proposes a robust control approach to achieve high-precision trajectory tracking for permanent magnet linear motor (PMLM) system containing uncertainties by describing the dynamic model of PMLM based on the Udwadia-Kalaba equation combined with constraint-following method. First, the system of PMLM is described as a constraint-following system by adding the generalized constraint force to the unconstrained Udwadia-Kalaba equation of PMLM system. Second, the robust constraint-following controller is designed based on the proposed model after uncertainty analysis. Moreover, the proposed controller is verified to guarantee deterministic performance for uncertain systems: uniformly bounded and uniformly ultimately bounded. Third, the numerical simulation and experimental validation demonstrate the effectiveness of proposed controller. Finally, the design approach of constraint-following can be applied to other systems with uncertainties.

Achieving the high-precision control of cable-driven parallel robots (CDPRs) is complex because of their structural properties. In this paper, a quintessential redundant CDPR is designed as the research subject, and a continuous switching sliding mode controller based on workspace vision is implemented to enhance the accuracy and stability of trajectory tracking. In addition, a virtual prototype of the CDPR with uncertainties is created in the simulation analysis software ADAMS, and co-simulation is performed with the control system designed in Simulink to validate the effectiveness of the proposed control strategy. Furthermore, a CDPR platform is established for trajectory tracking experiments using the visual-based position feedback method. The trajectory tracking performance with the three control schemes is then evaluated. The experimental results show that the continuous switching sliding mode control algorithm can significantly decrease trajectory tracking errors and exhibit superior trajectory tracking performance compared to the other control strategies.

Lower limb exoskeletons (LLEs) have demonstrated their potential in delivering quantified repetitive gait training for individuals afflicted with gait impairments. A critical concern in robotic gait training pertains to fostering active patient engagement, and a viable solution entails harnessing the patient’s intrinsic effort to govern the control of LLEs. To address these challenges, this study presents an innovative online gait learning approach with an appropriate control strategy for rehabilitation exoskeletons based on dynamic movement primitives (DMP) and an Assist-As-Needed (AAN) control strategy, denoted as DMP-AAN. Specifically tailored for post-stroke patients, this approach aims to acquire the gait trajectory from the unaffected leg and subsequently generate the reference gait trajectory for the affected leg, leveraging the acquired model and the patient’s personal exertion. Compared to conventional AAN methodologies, the proposed DMP-AAN approach exhibits adaptability to diverse scenarios encompassing varying gait patterns. Experimental validation has been performed using the lower limb rehabilitation exoskeleton HemiGo. The findings highlight the ability to generate suitable control efforts for LLEs with reduced human-robot interactive force, thereby enabling highly patient-controlled gait training sessions to be achieved.

This paper provides the methodology used to simulate and control an icosahedral tensegrity structure augmented with movable masses attached to each bar to provide a means of locomotion. The center of mass of the system can be changed by moving the masses along the length of each of the bars that compose the structure. Moving the masses changes the moments created by gravitational force, allowing for the structure to roll. With this methodology in mind, a controller was created to move the masses to the desired locations to cause such a roll. As shown later in this paper, such a methodology, assuming the movable masses have the required mass, allows for full control of the system using a quasi-static controller created specifically for this system. This system has advantages over traditional tensegrity controllers because it retains its shape and is designed for high-shock scenarios.

In the field of laparoscopic surgery, research is currently focusing on the development of new robotic systems to assist practitioners in complex operations, improving the precision of their medical gestures. In this context, the performance of these robotic platforms can be conditioned by various factors, such as the robot’s accessibility and dexterity in the task workspace. In this paper, we present a new strategy for improving the kinematic and dynamic performance of a 7-degrees of freedom robot-assisted camera-holder system for laparoscopic surgery. This approach involves the simultaneous optimization of the robot base placement and the laparoscope mounting orientation. To do so, a general robot capability representation approach is implemented in an innovative multiobjective optimization algorithm. The obtained results are first evaluated in simulation and then validated experimentally by comparing the robot’s performances implementing both the existing and the optimized solution. The optimization result led to a 2% improvement in the accessibility index and a 14% enhancement in manipulability. Furthermore, the dynamic performance criteria resulted in a substantial 43% reduction in power consumption.

This paper is concerned with the problem of collision-free path planning for manipulators in multi-obstacle scenarios. Aiming at overcoming the deficiencies of existing algorithms in excessive time consumption and poor expansion quality, a path planning algorithm named Fast Bi-directional Rapidly-exploring Random Tree (FBi-RRT) with novel heuristic node expansion is proposed, which includes a selective-expansion strategy and a vertical-exploration strategy. The selective-expansion strategy is designed to guide the selection of the nearest-neighbor node to avoid the repeated expansion failure, thereby shortening the overall planning time. Also, the vertical-exploration strategy is developed to regulate the expansion direction of the collision nodes to escape from the obstacle space with less blindness, thus improving the expansion quality and further reducing time cost. Compared with previous planning algorithms, FBi-RRT can generate a feasible path for manipulators in a drastically shorter time. To validate the effectiveness of the proposed heuristic node expansion, FBi-RRT is conducted on a 6-DOF manipulator and tested in five scenarios. The experimental results demonstrate that FBi-RRT outperforms the existing methods in time consumption and expansion quality.

The flexible flat cable (FFC) assembly task is a prime challenge in electronic manufacturing. Its characteristics of being prone to deformation under external force, tiny assembly tolerance, and fragility impede the application of robotic assembly in this field. To achieve reliable and stable robotic automation assembly of FFC, an efficient assembly skill acquisition strategy is presented by combining a parallel robot skill learning algorithm with adaptive impedance control. The parallel robot skill learning algorithm is proposed to enhance the efficiency of FFC assembly skill acquisition, which reduces the risk of damaging FFC and tackles the uncertain influence resulting from deformation during the assembly process. Moreover, FFC assembly is also a complex contact-rich manipulation task. An adaptive impedance controller is designed to implement force tracking during the assembly process without precise environment information, and the stability is also analyzed based on the Lyapunov function. Experiments of FFC assembly are conducted to illustrate the efficiency of the proposed method. The experimental results demonstrate that the proposed method is robust and efficient.

Prostate cancer is the second most common malignancy in American men. High-dose-rate brachytherapy is a popular treatment technique in which a large, localized radiation dose is used to kill cancer. Utilization of curvilinear catheter implantation inside the prostate gland to provide access channels to host the radiation source has shown superiority in terms of improved dosimetric constraints compared to straight needles. To this aim, we have introduced an active needle to curve inside the prostate conformal to the patient’s specific anatomical relationship for improved dose distribution to the prostate and reduced toxicity to the organs at risk. This work presents closed-loop control of our tendon-driven active needle in water medium and air using the position feedback of the tip obtained in real time from an ultrasound (US) or an electromagnetic (EM) tracking sensor, respectively. The active needle consists of a compliant flexure section to realize bending in two directions via actuation of two internal tendons. Tracking errors using US and EM trackers are estimated and compared. Results show that the bending angle of the active needle could be controlled using position feedback of the US or the EM tracking system with a bending angle error of less than 1.00 degree when delay is disregarded. It is concluded that the actuation system and controller, presented in this work, are able to realize a desired bending angle at the active needle tip with reasonable accuracy paving the path for tip tracking and manipulation control evaluations in a prostate brachytherapy.

Continuum robot has become a research hotspot due to its excellent dexterity, flexibility and applicability to constrained environments. However, the effective, secure and accurate path planning for the continuum robot remains a challenging issue, for that it is difficult to choose a suitable inverse kinematics solution due to its redundancy in the confined environment. This paper presents a collision-free path planning method based on the improved artificial potential field (APF) for the cable-driven continuum robot, in which the beetle antennae search algorithm is adopted to deal with the optimal problem of APF without the necessary for velocity kinematics. In addition, the local optimum problem of traditional APF is solved by the randomness of the antennae’s direction vector which can make the algorithm easily jump out of local minima. The simulation and experimental results verify the efficiency of the proposed path planning method.

Motivated by practical applications of inspection and maintenance, we have developed a wall-climbing robot with passive compliant mechanisms that can autonomously adapt to curved surfaces. At first, this paper presents two failure modes of the traditional wall-climbing robot on the variable curvature wall surface and further introduces the designed passive compliant wall-climbing robot in detail. Then, the motion mechanism of the passive compliant wall-climbing robot on the curved surface is analyzed from stable adsorption conditions, parameter design process, and force analysis. At last, a series of experiments have been carried out on load capability and curved surface adaptability based on a developed principle prototype. The experimental results indicated that the wall-climbing robot with passive compliant mechanisms can effectively promote both adsorption stability and adaptability to variable curvatures.

Aimed at the challenges of wide-angle mobile robot visual perception for diverse field applications, we present the spherical robot visual system that uses a 360° field of view (FOV) for realizing real-time object detection. The spherical robot image acquisition system model is developed with optimal parameters, including camera spacing, camera axis angle, and the distance of the target image plane. Two 180$^{\circ}$-wide panoramic FOVs, front and rear view, are formed using four on-board cameras. The speed of the SURF algorithm is increased for feature extraction and matching. For seamless fusion of the images, an improved fade-in and fade-out algorithm is used, which not only improves the seam quality but also improves object detection performance. The speed of the dynamic image stitching is significantly enhanced by using a cache-based sequential image fusion method. On top of the acquired panoramic wide FOVs, the YOLO algorithm is used for real-time object detection. The panoramic visual system for the spherical robot is then tested in real time, which outputs panoramic views of the scene at an average frame rate of 21.69 fps and panoramic views with object detection at an average of 15.39 fps.

To solve the constant contact force control problem between the end tool of a 5 degrees of freedom hybrid optical mirror processing robot and a workpiece, an adaptive impedance control method for the pneumatic servo-polishing system of the robot is designed. Firstly, the pneumatic servo-polishing control system at the end of the robot is set up. Secondly, the impedance control method for contact force is investigated based on the mathematical model of the pneumatic servo-polishing control system. Additionally, the causes of steady-state error of impedance control are analyzed theoretically, and the calculation method for steady-state error of impedance control is deduced. Finally, an indirect adaptive impedance controller based on Lyapunov Stability Principle is developed to estimate the environmental stiffness and position online, so as to reduce steady-state error and realize the tracking of polishing contact force. The simulation and experimental results suggest that the adaptive impedance control method not only recognizes that the contact force of the robot is relatively constant during the polishing process but also has high control accuracy for the force, fast-tracking response for the abrupt force, and considerable adaptability to the variable environmental stiffness.

We proposed a compliant leg configuration that enhances the conventional pantograph design with leaf springs. The following facts characterize the proposed configuration: (1) Due to the use of the pantograph structure, the mass is centralized around the hip joint, reducing the lower leg inertia; (2) Leaf springs are chosen as elastic parts to increase energy efficiency and estimate foot-end contact forces. Compared with coil springs, leaf springs require no guide rails to deploy, and their stiffness can be easily adjusted through shape cutting. Analytical models are introduced to analyze the leg’s stiffness and estimate the contact forces only with the deflections of leaf springs. A one-leg robot based on the proposed design is built, and various experiments are conducted. Experiments regarding the stiffness calibration and the contact forces estimation showed an acceptable agreement with the analytical model. Experiments of dropping demonstrate the feasibility of the leg to perform spring-like behaviors. Experiments of periodic hopping demonstrate the feasibility of using spring deflections to detect touch-down events. For energy efficiency, it is also observed that the elastic leg has a 20% increment concerning the jumping height in the flight phase, compared with the one where leaf springs are replaced with rigid materials.

As space missions are needed in the future, the assembly volume of the space truss will become larger and larger, and the advancing path of the on-orbit cellular robot to the mission target will become more and more complicated. If the shortest moving path cannot be found in the truss environment, the climbing time of the robot on the truss will be greatly increased. To improve the speed of the cellular robot moving to the target point on the large space truss, this paper designs a cellular robot structure and configuration suitable for climbing on the truss and uses the improved sparrow algorithm to solve the problem of robot motion path planning. By establishing a mathematical model of the space truss, the improved sparrow algorithm is used to find the shortest path between the starting point and the end point in the truss environment. Finally, the data of this algorithm are compared with the data of other algorithms. The data results show that the improved sparrow algorithm is very effective in solving the optimal path of the space truss. The improved sparrow algorithm keeps the same optimal path compared with the standard sparrow algorithm, and the overall reaction time is increased by 51.60%, and the number of effective iterations is increased by about 13.87%.

The rise in the number of automated robotic kitchens accelerated the need for advanced food handling system, emphasizing food analysis including ingredient classification pose recognition and assembling strategy. Selecting the optimal piece from a pile of similarly shaped food items is a challenge to automated meal assembling system. To address this, we present a constructive assembling algorithm, introducing a unique approach for food pose detection–Fast Image to Pose Detection (FI2PD), and a closed-loop packing strategy. Powered by a convolutional neural network (CNN) and a pose retrieval model, FI2PD is adept at constructing a 6D pose from only RGB images. The method employs a coarse-to-fine approach, leveraging the CNN to pinpoint object orientation and position, alongside a pose retrieval process for target selection and 6D pose derivation. Our closed-loop packing strategy, aided by the Item Arrangement Verifier, ensures precise arrangement and system robustness. Additionally, we introduce our FdIngred328 dataset of nine food categories ranging from fake foods to real foods, and the automatically generated data based on synthetic techniques. The performance of our method for object recognition and pose detection has been demonstrated to achieve a success rate of 97.9%. Impressively, the integration of a closed-loop strategy into our meal-assembly process resulted in a notable success rate of 90%, outperforming the results of systems lacking the closed-loop mechanism.