We theoretically studied how the electric filed effect can modify thermoelectric properties of intrinsic bismuth telluride nanowires, which are grown along [110] direction. The electronic structure and wave functions were calculated by solving the self-consistent system of the Schrodinger and Poisson equations by means of both the Thomas-Fermi approximation and the spectral element method. The thermoelectric parameters were determined using a constant relaxation-time approximation. The external electric field can increase the Seebeck coefficient of a nanowire with 7 - 15 nm lateral dimensions by nearly a factor of two, and enhance the figure of merit by an order of magnitude.

We use a Thermoreflectance Thermal Imaging technique to study the transient cooling of SiGe-based microrefrigerators. Thermal imaging with submicron spatial resolution, 0.1C temperature resolution and 100 nanosecond temporal resolution is achieved. Transient temperature profiles of SiGe-based superlattice microrefrigerator devices of different sizes are obtained. The dynamic behavior of these microrefrigerators, show an interplay between Peltier and Joule effects. On the top surface of the device, Peltier cooling appears first with a time constant of about 10-30 microseconds, then Joule heating in the device starts taking over with a time constant of about 100-150 microseconds. The experimental results agree very well with the theoretical predictions based on Thermal Quadrupoles Method. The difference in the two time constants can be explained considering the thermal resistance and capacitance of the thin film. In addition this shows that the Joule heating at the top metal/semiconductor interface does not dominate the microrefrigerator performance or else we would have obtained the same time constants for the Peltier and Joule effects. Experimental results show that under high current values, pulse-operation the microrefrigerator device can provide cooling for about 30 microseconds, even though steady state measurements show heating. Temperature distribution on the metal leads connected to the microrefrigerator’s cold junction show the interplay between Joule heating in the metal as well as heat conduction to the substrate. Modeling is used to study the effect of different physical and geometrical parameters of the device on its transient cooling. 3D geometry of heat and current flow in the device plays an important role. One of the goals is to maximize cooling over the shortest time scales.

A recent theoretical study suggested that the substitution of Cd in PbTe can result in a distortion in the electronic density of states (DOS) near the bottom of the conduction band in PbTe. In this study we explored the effect of Cd doping on the thermoelectric properties of PbTe in an effort to test the theoretical prediction that DOS distortion can increase the Seebeck coefficient. We present detailed investigation of structural and spectroscopic data, transmission electron microscopy, as well as transport properties of samples of PbI2 doped PbTe-x% CdTe (x = 1, 3, 5, 7, 10). All samples follow the Pisarenko relationship and no enhancement of the Seebeck coefficient was observed due to DOS distortions. A low lattice thermal conductivity was achieved by nanostructuring observed via high resolution transmission electron microscopy. A maximum ZT of ˜1.2 at ˜720 K was achieved for the 1% CdTe sample.

A survey of state of the art of the development of high temperature materials is presented and will be discussed in comparison to the situation in the 1990th. An attempt will be made to assess the state of the art of the materials thermoelectric properties, their technical level, and possible potential for standardized device technology. Also a first assessment based on current commodity prices for some important thermoelectric compounds will be made. As a roundup advantages and drawbacks for some classical and upcoming compounds will be given. The main challenges, which will have to be overcome to finally enable thermoelectric power generation as a recycling technology of “nomadic” energy, will be summarized. As a result, thermoelectrics should play an important role in the field of green energies.

We previously reported the synthesis of nanostructured composite PbTe with excess Pb and Sb metal inclusions. The electrical conductivity shows an unusual temperature dependence that depends on the inclusion Pb/Sb ratio, resulting in marked enhancements in power factor and ZT at 700 K. Additional investigation of the transport and structure of these materials is reported here. Measurements of the scattering parameter reveals there is little change in electron scattering with respect to pure PbTe. High resolution electron microscopy was used to determine additional information about the nature of the precipitate phases present in the samples. High temperature transmission electron microscopy reveals that the precipitates begin to dissolve at high temperatures and completely disappear at T > 619K. A qualitative explanation of the unusual transport behavior of these materials is presented.

Electronic properties of ternary skutterudites AX3/2Y3/2 (A=Co, X=Ge, Sn and Y=S, Te) are investigated using first principles calculations to clarify recent experimental results. Band derivatives are computed accurately within an approach based on Maximally Localized Wannier Functions (MLWFs). Band structures exhibit larger effective masses compared to parental binary CoSb3. Our results also indicate a more parabolic dispersion near the top of the valence band and a multivalley character in both conduction and valence band. Despite the improved thermopower these skutterudites has relatively low power factor due to increased resistivity. The fundamental cause of such large resistivity seems to be associated with the ionicity of the bonding.

In order to restrain global warming and to realize a sustainable global energy system, further enhancements in energy efficiency are required. One reliable technology for reducing greenhouse gas emissions and the consumption of fossil fuel is thermoelectric technology, which can directly convert heat into electricity and consequently increases the energy conversion efficiency of power generation by combustion. Magnesium silicide (Mg2Si) is a promising candidate for a thermal-to-electric energy-conversion material at operating temperatures ranging from 500 to 800 K. Mg2Si exhibits many promising characteristics, such as the abundance of its constituent elements in the earth’s crust and the non-toxicity of its processing by-products, resulting in freedom from concerns regarding prospective extended restrictions on hazardous substances. The efficiency of a thermoelectric device is characterized by the dimensionless figure of merit, ZT. It is well known that several kinds of dopants are effective in improving the thermoelectric performance of n-type Mg2Si. With Bi-doped n-type Mg2Si, we have achieved a maximum value of the dimensionless figure-of-merit ZT of ˜1.0 at ˜ 850 K. However, the correlation between the ZT values and the power generation characteristics, which is essential to understand in order to design a structure for a TE power generation module, has not been sufficiently investigated. In order to design a structure for a thermoelectric module using Mg2Si, we examined the correlation between the ZT values and the power-output of a single element using Mg2Si (ZT = 0.6) and Mg2Si doped with donor impurities such as Al and/or Bi (ZT = 0.65˜0.77). The measured single element was 2×2 mm2 in section and 10 mm long. Additionally, we developed and evaluated a new architecture based on a ‘unileg’ structure Mg2Si TE power generation module, which can improve the module lifetime and simplify its manufacture. As a starting material for the fabrication of the single element and the TE modules, pre-synthesized polycrystalline Mg2Si, fabricated by UNION MATERIAL was used. The material was sintered using a plasma-activated sintering (PAS) technique, and, at the same time, Ni electrodes were formed on the Mg2Si by employing of a monobloc PAS technique. The thermoelectric power-outputs were measured under a temperature difference, ΔT, ranging from 100-to-500 K by using UNION MATERIAL UMTE-1000M. The observed power-output for single element of Mg2Si (ZT = 0.6), 2 at % Bi-doped Mg2Si (ZT = 0.65) and 1at % Bi + 1at % Al-doped Mg2Si (ZT = 0.77) were 23.2 mW, 13.6 mW and 19.4 mW respectively at ΔT = 500 K (between 873 K and 373 K). For the new architecture based on the unileg structure thermoelectric module, the observed value for power-output-per-unit-area was 12 mW/mm2 at ΔT = 500 K.

The dimensionless thermoelectric figure-of-merit (ZT) in bulk materials has remained about 1 for many years. Here we show that a significant ZT improvement can be achieved in nanocrystalline bulk materials. These nanocrystalline bulk materials were made by hot-pressing nanopowders that are ball-milled from either crystalline ingots or elements. Electrical transport measurements, coupled with microstructure studies and modeling, show that the ZT improvement is the result of low thermal conductivity caused by the increased phonon scattering by grain boundaries and defects. More importantly, the nanostructure approach has been demonstrated in a few thermoelectric material systems, proving its generosity. The approach can be easily scaled up to multiple tons. Thermal stability studies have shown that the nanostructures are stable at the application temperature for an extended period of time. It is expected that such enhanced materials will make the existing cooling and power generation systems more efficient.

The figure of merit ZT = sS2T/k (S the Seebeck coefficient, s and k the electrical and thermal conductivity respectively) is an essential element of the efficiency of a thermoelectric material for applications which convert heat to electricity or, conversely, electric current to cooling. From the expression of the power factor sS2 it was deduced that a highly degenerated semiconductor is necessary. In order to reduce the lattice part of the thermal conductivity, various mechanisms were tested in new thermoelectric materials and those had been the topics of several reviews. These include cage-like materials, effects of vacancies, solid solutions, complex structures (cluster, tunnel, …,), micro- and nano-structured systems, and more recently semiconducting glasses. We plan to review such aspects in the modern thermoelectric materials and include results of the very last years. Moreover, as micro- and nano-composites seem to be promising to increase ZT in large size samples, we will also briefly discuss the interest of spark plasma sintering technique to preserve the micro- or nano- structure in highly densified samples.

The thermoelectric (TE) properties, such as the Seebeck coefficient, the electrical and thermal conductivities, and the output power, of Sb-doped n-type Mg2Si were studied. A commercial polycrystalline source was used for the source material for the Mg2Si. TE elements with Ni electrodes were fabricated by using a monobloc plasma-activated sintering (PAS) technique. Compared with undoped samples, the ZT values of the Sb-doped samples were higher over the whole temperature range in which measurements were made; the maximum value for the Sb doped Mg2Si was 0.72 at 864 K. The TE characteristics of Sb-doped samples were found to be comparable to those of Bi-doped ones, and no significant difference in ZT value was observed between them. Provisional results showed that the maximum value of the output power was 6.75 mW for the undoped sample, 4.55 mW for a 0.5 at% Sb doped sample, and 5.25 mW for a 1 at% Sb doped sample with ΔT = 500 K (between 873 K and 373 K).