Hostname: page-component-586b7cd67f-t7czq Total loading time: 0 Render date: 2024-11-20T13:37:51.060Z Has data issue: false hasContentIssue false
  • English
  • Français

Trench and Via Filling with Electroplated Copper: Effect of Current Density and Pulse Waveform

Published online by Cambridge University Press:  17 March 2011

C. H. Seah ,
S. Mridha ,
Y. K. Siew ,
G. Sarkar  and
L. H. Chan
C. H. Seah
Affiliation:
Thin Film Dept., Chartered Silicon Partners Pte Ltd., 60 Woodlands Industrial Park D, Street 2, Singapore 738406, Singapore Phone/Fax: (65)-3946348/3946516 Email: [email protected]
S. Mridha
Affiliation:
School of Applied Science, Nanyang Technological University, Nanyang Avenue, Singapore 639798, Singapore
Y. K. Siew
Affiliation:
School of Applied Science, Nanyang Technological University, Nanyang Avenue, Singapore 639798, Singapore
G. Sarkar
Affiliation:
School of Applied Science, Nanyang Technological University, Nanyang Avenue, Singapore 639798, Singapore
L. H. Chan
Affiliation:
Research & Development Dept., Chartered Semiconductor Manufacturing Ltd., 60 Woodlands Industrial Park D, Street 2, Singapore 738406, Singapore
Get access

Abstract

A study was carried out to investigate the effect of current density and pulse waveform on the filling of line trenches and contact vias with aspect ratio of 2:1 for sub-0.25 µm device manufacturing using normal pulse plating of copper. The growth pattern of the copper films deposited using 0.05 and 0.10 A/cm2 current density gave no significant difference. Small grains were seen to have nucleated uniformly across the line trenches and via holes after 1 second of electroplating. With increasing the deposition time to 2 seconds, a slight buildup of the film thickness was observed in both trenches and vias without significant increase in the size of the copper grains. Grain growth involving the coalescence of small grains occurred after 5 seconds of plating and a further buildup in thickness and fill up of the trenches and vias occurred after 10 seconds of deposition.

When the patterned wafers were plated with a pulse waveform of 3 ms on and 0.5 ms off, the filling of trenches could not be complete after 30 seconds of electroplating. A complete filling of the trenches was achieved within 30 seconds of deposition using a pulse waveform of 6 to 8 ms on and 1 to 2 ms off. When the on-period was increased above this range to 9.9 ms, voids were observed at the centre of the via holes.

Type
Research Article
Information
MRS Online Proceedings Library (OPL) , Volume 612: Symposium D – Materials, Technology & Reliability for Advanced Interconnects.. , 2000 , D9.1.1
Copyright
Copyright © Materials Research Society 2000

Access options

Get access to the full version of this content by using one of the access options below. (Log in options will check for institutional or personal access. Content may require purchase if you do not have access.)

References

1. Venkatesan, S. et al. , Proc. IEDM Conf., (1997) p. 769 Google Scholar
2. Edelstein, D. et al. , Proc. IEDM Conf., (1997) p. 773 Google Scholar
3. Contolini, R.J., Tarte, L., Graff, R.T., Evans, L.B., Cox, J.N., Puich, M.R., Gee, J.D., Mu, X.-C. and Chiang, C., VMIC 12 (1995) p. 322 Google Scholar
4. Dubin, V. M., Ting, C. H. and Cheung, R., VMIC 14 (1997) p. 69 Google Scholar
5. Heidenreich, J. et al. , IITC 1 (1998) p. 151 Google Scholar
6. Blaschke, V. et al. , IITC 1 (1998) p. 154 Google Scholar
7. Ritzdorf, T., Graham, L., Jin, S., Mu, C. and Fraser, D., IITC 1 (1998) p. 166 Google Scholar
8. Principles of Electronics Packaging, by Seraphim, D. P., Lasky, R. and Li, C. Y., McGraw-Hill (1989)10.1115/1.3226524Google Scholar
9. Andricacos, P.C., Uzoh, C., Dukovic, J.O., Horkans, J. and Deligianni, H., Adv. Metallization Conf. in 1998, (MRS 1999) p. 29 Google Scholar
10. Lopatin, S. et al. , Adv. Metallization Conf. in 1998, (MRS 1999) p. 35 Google Scholar
11. Reid, J. et al. , IITC 2 (1999) p. 284 Google Scholar
12. Seah, C.H., Mridha, S. and Chan, L.H., IITC 1 (1998) p. 157 Google Scholar