Hostname: page-component-586b7cd67f-g8jcs Total loading time: 0 Render date: 2024-11-29T06:57:42.208Z Has data issue: false hasContentIssue false
  • English
  • Français

A Study on the Properties of Different IMP Ta, Ta(N) and Multi-Layer Ta/Ta(N) as Diffusion Barriers for Cu Metallization

Published online by Cambridge University Press:  17 March 2011

L. He ,
C.Y. Li ,
Z.Q. Zeng ,
J.J. Wu ,
Y. Qian ,
Y. Zhang ,
H.D. Liu  and
Joseph Xie
L. He
Affiliation:
Advanced Materials Program, Singapore-MIT Alliance, Singapore Dept of Deep Submicron Integrated Circuit, Institute of Microelectronics, Singapore
C.Y. Li
Affiliation:
Dept of Deep Submicron Integrated Circuit, Institute of Microelectronics, Singapore
Z.Q. Zeng
Affiliation:
School of Materials Engineering, Nanyang Technological University, Singapore
J.J. Wu
Affiliation:
Dept of Deep Submicron Integrated Circuit, Institute of Microelectronics, Singapore
Y. Qian
Affiliation:
Dept of Deep Submicron Integrated Circuit, Institute of Microelectronics, Singapore
Y. Zhang
Affiliation:
Advanced Materials Program, Singapore-MIT Alliance, Singapore Dept of Deep Submicron Integrated Circuit, Institute of Microelectronics, Singapore
H.D. Liu
Affiliation:
Rudolph Technologies, Inc., Flanders, NJ
Joseph Xie
Affiliation:
Advanced Materials Program, Singapore-MIT Alliance, Singapore Dept of Deep Submicron Integrated Circuit, Institute of Microelectronics, Singapore
Get access

Abstract

We report a study on the properties of Ionized Metal Plasma (IMP) Ta, Ta(N) and multi-layer Ta/Ta(N) based on a comparative evaluation of their performance as diffusion barriers in Cu based metallization schemes. The film structures used in this study are: IMP Cu(2000Å)/IMP Ta(250Å)/Si; IMP Cu(2000Å)/IMP Ta(N)(250Å)/Si; and IMP Cu(2000Å)/IMP multi-layer Ta/Ta(N)(250Å)/Si. The samples were annealed in N2 ambient at 500 °C, 550°C, 600°C and 650°C, respectively, for 30 minutes. The failure behavior and film properties of different barriers were investigated using MetaPULSE, Film stress measurement (FSM), Four-point probe (FPP), X-ray diffractometry (XRD), Field emission scanning electron microscopy (FESEM) and Transmission electron microscopy (TEM). It has been observed clearly from the sheet resistance measurements that failures of Ta(N) and Ta barriers occurred at 550°C and 600°C respectively, whereas the multi-layer Ta/Ta(N) could still survive from the annealing up to 650°C. Evidence showing the formation of Cu3Si in the failed film stacks was found from XRD spectra. Based on our studies, it can be concluded that microstructures of the barriers has the major effects on preventing Cu from diffusing through them to react with Si and this makes the multi-layer Ta/Ta(N), in overall, superior to the other two Ta and Ta(N) barriers.

Type
Research Article
Information
MRS Online Proceedings Library (OPL) , Volume 714: Symposium – Materials, Technology and Reliability for Advanced Interconnects and Low-k Dielectrics II , 2001 , L5.6.1
Copyright
Copyright © Materials Research Society 2001

Access options

Get access to the full version of this content by using one of the access options below. (Log in options will check for institutional or personal access. Content may require purchase if you do not have access.)

References

REFERENCES

[1] Lee, M.K., Wang, H.D., Wang, J.J., 1997, “A Cu seed layer for Cu deposition on silicon”, Solid-State Electronics, Vol.41, pp. 695–702 Google Scholar
[2] Torres, J., Mernet, J.L., Madar, R., Crean, G., Gessner, T., Bertz, A., 1996, “Copper-based metallization for ULSI circuits”, Microelectronic Engineering, Vol 34, pp. 119–122 Google Scholar
[3] Jang, Si-Yeoul, Lee, Sung-man, 1996, “Tantalum and niobium as a diffusion barrier between copper and silicon”, J. Mat. Sci.,: Materials in Electronics, Vol.7, pp. 271–278 Google Scholar
[4] Shepherd, K., Kelber, J., 1999, “Interactions of copper with oxidized TaSiN”, Applied Surface Science, Vol.151, pp. 287–298 Google Scholar
[5] Stavrev, M., Fischer, D., Wenzel, C., Heiser, T., 1997, “Study of Ta(N,O) diffusion barrier stability: analytical and electrical characterization of low level Cu contamination in Si,” Microelectronic Engineering, Vol. 37/38, pp. 245–251.Google Scholar
[6] Tanaka, Y., Xu, Z., Gopalraja, P., Forster, J., Yao, G., Zhang, H., 1998, “Sub-quarter micron metallization using ionized metal plasma (IMP) technology,” Vacuum, Vol. 51, pp. 729–733.Google Scholar
[7] Wang, M.T., Lin, Y.C., Chen, M.C., 1998, “Barrier properties of very thin Ta and TaN layers against Cu diffusion”, J. Electrochem. Soc., Vol. 145, pp. 2538–2545.Google Scholar
[8] Holloway, Karen, Fryer, Peter M., Cabral, Cyril, 1992, “Ta as a diffusion barrier between copper and Si: failure mechanism and effect of N additions,” J. Appl. Phys. Vol. 71, pp. 5433–5444.Google Scholar
[9] Wang, Shi-Qing, 1994, “Barriers Against Copper Diffusion into silicon and drift through silicon dioxide”, MRS Bulleting, pp. 30–40.Google Scholar
[10] Clevenger, L.A., Bojarczuk, N.A., Holloway, K., Harper, J.M. E., 1993, “Comparison of high vacuum an dultra-high-vaccum Ta diffusion barrier performance against copper penetration,” J. Appl. Phys. Vol. 73, pp. 300–308.Google Scholar
[11] Cho, Sung-Lae, Kim, Ki-Bum, Min, Seok-Hong, 1999, “Diffusion barrier properties of metallization chemical vapor deposited TaN films against Cu diffusion,” J. Electrochem. Soc., Vol 146, pp. 3724–3730.Google Scholar
[12] He, L., Li, C.Y., Xie, Joseph, 2001, “IMP Ta, Ta(N) and Multi-layer Ta/Ta(N) as Diffusion Barriers for Cu Metallization”, Symposium of Singapore-MIT Alliance, Singapore Google Scholar