Hostname: page-component-78c5997874-4rdpn Total loading time: 0 Render date: 2024-11-20T04:11:38.643Z Has data issue: false hasContentIssue false
  • English
  • Français

Optimized screen-printing and SEM-FIB characterization of YSZ thin films for Solid Oxide Fuel Cells and gas sensors devices

Published online by Cambridge University Press:  15 March 2011

A. Morata ,
A. Tarancón ,
G. Dezanneau ,
F. Peiró  and
J. R. Morante
A. Morata
Affiliation:
Electronics Materials and Engineering (EME), Department of Electronics, University of Barcelona, Spain
A. Tarancón
Affiliation:
Electronics Materials and Engineering (EME), Department of Electronics, University of Barcelona, Spain
G. Dezanneau
Affiliation:
Electronics Materials and Engineering (EME), Department of Electronics, University of Barcelona, Spain
F. Peiró
Affiliation:
Electronics Materials and Engineering (EME), Department of Electronics, University of Barcelona, Spain
J. R. Morante
Affiliation:
Electronics Materials and Engineering (EME), Department of Electronics, University of Barcelona, Spain
Get access

Abstract

In the present work, the screen printing technique has been used to deposit thick films of Zr0.84Y016O1.92 (8YSZ). In order to control the final porosity in view of a specific application (SOFCs or gas sensor), an experimental design based on analysis of variances (ANOVA) has been carried out. From this, we were able to determine the influence of several technological parameters on films porosity and grain size. The films obtained have been analysed with both Scanning Electron Microscopy (SEM) and Focused Ion Beam (FIB) combined with SEM. We show that only the combination of experimental design and advanced observation technique such as Focused Ion Beam allowed us to extract significant information for the improvement of the deposition process.

Type
Research Article
Information
MRS Online Proceedings Library (OPL) , Volume 822: Symposium S – Nanostructured Materials in Alternative Energy Devices , 2004 , S6.11
Copyright
Copyright © Materials Research Society 2004

Access options

Get access to the full version of this content by using one of the access options below. (Log in options will check for institutional or personal access. Content may require purchase if you do not have access.)

References

[1] Will, J., Mitterforder, A., Kleinlogel, C., Perednis, D., Gauckler, L.J., “Fabrication of thin electrolytes for second-generation solid oxide fuel cells” Solid State Ionics 131 (2000) 79–96 Google Scholar
[2] Golovanov, V., Solis, V.L., Lantto, V., Leppävuori, S. “SnO2 Different thick film methods in printing of one electrode semiconductor gas sensor” Sensors and Actuators B 34 (1996) 401–406.Google Scholar
[3] Xia, Changron, Chen, Frangrin, and Liu, Meilin, “Reduced Temperature Solid Oxide Fuel Cells Fabricated by Screen Printing” Electrochemical and Solid State Letters, 4 (5) A52–A54 (2001).Google Scholar
[4] Shiau, F., Fang, T.-T., Leu, T.-H., “Effects of Milling and Particle Size Distribution on the Sintering Behavior and Evolution of the Microstructure in Sintering Powder Compacts”, Materials Chemistry and Physics, 57 (1998) 33–40.Google Scholar
[5] Frenkel, H., Hellmig, R.J., “Effect of Nanopowder Deagglomeration on the Densities of Nanocrystalline Ceramic Green Bodies and their Sintering Behaviour”, NanoStructured Materials, 11 (1999) 617–662.Google Scholar
[6] Barker, T. B., “Quality by Experimental Design”, Quality and reliability 4, Edited by Barker, Thomas B.. Center for Quality and Applied Statistics, Rochester Institute of Technology, 1985.Google Scholar
[7] Gopaul, J., Maskell, W.C., Pitt, K.E., “Planar oxygen sensor. Part I: Effect of crazing of a zorconia thick film on an alumina substrate” Journal of applied electrochemistry, 29 (1999) 93–100.Google Scholar