Hostname: page-component-cd9895bd7-fscjk Total loading time: 0 Render date: 2024-12-27T02:04:49.891Z Has data issue: false hasContentIssue false
  • English
  • Français

The Use of Gravure Offset Printing in the Realisation of Fine Line Thick Film Conductors

Published online by Cambridge University Press:  15 February 2011

S. LeppÄvuori ,
J. VÄÄnÄnen ,
M. Lahti ,
K. Kukkola  and
A. UusimÄki
S. LeppÄvuori
Affiliation:
Microelectronics and Material Physics Laboratories, University of Oulu, FIN-90570 Oulu, Finland
J. VÄÄnÄnen
Affiliation:
Microelectronics and Material Physics Laboratories, University of Oulu, FIN-90570 Oulu, Finland
M. Lahti
Affiliation:
Microelectronics and Material Physics Laboratories, University of Oulu, FIN-90570 Oulu, Finland
K. Kukkola
Affiliation:
Microelectronics and Material Physics Laboratories, University of Oulu, FIN-90570 Oulu, Finland
A. UusimÄki
Affiliation:
Microelectronics and Material Physics Laboratories, University of Oulu, FIN-90570 Oulu, Finland
Get access

Abstract

The use of gravure offset printing to transfer film patterns from an inked plate to the substrate by a silicone rubber pad has been shown to have promising advantages in fine line and multilayer production. The technology is now moving into the field of electronics manufacturing. By optimising the printing parameters and ink characteristics in the gravure offset technique, lines and spaces as narrow as 50 μtm were achieved and even finer lines are possible. Commercially available fine line thick film Au and Ag pastes were modified for this purpose. The thickness of sintered conductors ranged from about 2 to 11 μtm depending on ink viscosity, control of printing equipment and repetition of prints. When compared with films deposited by conventional thick film technology, the conductivity and adhesion on alumina were similr. The small interconnections between conductors through the insulator layer necessary in multilayer techniques were realised using gravure offset printing to coat excimer laser drilled vias. Interconnection diameters of less than 100 μtm were achieved.

Type
Research Article
Information
MRS Online Proceedings Library (OPL) , Volume 323: Symposium J – Electronic Packaging Materials Science VII , 1993 , 85
Copyright
Copyright © Materials Research Society 1994

Access options

Get access to the full version of this content by using one of the access options below. (Log in options will check for institutional or personal access. Content may require purchase if you do not have access.)

References

1. Shimada, M., Watanabe, H., Tsukamoto, M. and Ishida, T., Proc. IMC Tokyo, 1990 pp. 581–586.Google Scholar
2. Nakao, K., Hayama, M., Kuramasu, K., Shimada, M. and Tsukamoto, M., Extended Abstracts of the 1991 International Conference on Solid State Devices and Materials, Yokohama, 1991 pp. 599–601.Google Scholar
3. , Sidney Stein, J., Wahlers, Richard L., Cornelius Huang, Y.D. and Michael A. Stein, Proc. ISHM Conference, Orlando, Florida, 1991 pp. 130–134.Google Scholar
4. Leppivuori, S., Vdiiinnen, J., Lahti, M., Remes, J. and Uusimaki, A., accepted for publication in Sensors and Actuators.Google Scholar
5. Barrett, J. and Moran, P., Proc. ISHM Conference, Dallas, Texas, 1984 pp. 1–7.Google Scholar
6. Hirakawa, T. and Kato, C., Proc. IMC, Yokohama, June, 1992 pp. 56–59.Google Scholar
7. Haertling, C., Yoshikawa, S. and Newnham, R., Journal of the American Ceramic Society 73 (11), 3339–3344 (1990).CrossRefGoogle Scholar
8. Felten, J. and Collins, J., Proc. ISHM Conference, 1990 pp. 224–227.Google Scholar
9. Leppdvuori, S., Vdindnen, J., Lahti, M., paper to be published in the First European Conference on Electronic Packaging Technology, EuPac'94, 1–3 February, Essen, Germany Google Scholar