Hostname: page-component-cd9895bd7-lnqnp Total loading time: 0 Render date: 2024-12-25T04:48:04.161Z Has data issue: false hasContentIssue false
  • English
  • Français

Hydrothermal Synthesis of Bioinert Oxide Film on Pure Ti: In Vitro and In Vivo Studies

Published online by Cambridge University Press:  10 February 2012

Masato Ueda ,
Masahiko Ikeda ,
Richard Langford ,
Jeremy Skepper ,
Ruth E. Cameron  and
Serena M. Best
Masato Ueda
Affiliation:
Faculty of Chemistry, Materials and Bioengineering, Kansai University, Suita, Osaka 564-8680, JAPAN
Masahiko Ikeda
Affiliation:
Faculty of Chemistry, Materials and Bioengineering, Kansai University, Suita, Osaka 564-8680, JAPAN
Richard Langford
Affiliation:
Electron Microscopy Suite, The Cavendish Laboratory, University of Cambridge, Cambridge, CB3 0HE, UK
Jeremy Skepper
Affiliation:
Department of Physiology, Development and Neuroscience, University of Cambridge, Cambridge, CB2 3EG, UK
Ruth E. Cameron
Affiliation:
Cambridge Centre for Medical Materials, Department of Materials Science & Metallurgy, University of Cambridge, Cambridge, CB2 3QZ, UK
Serena M. Best
Affiliation:
Cambridge Centre for Medical Materials, Department of Materials Science & Metallurgy, University of Cambridge, Cambridge, CB2 3QZ, UK
Get access

Abstract

Titanium and its alloys have been employed in bone plates/screws, and these are often designed to be removed after recovery. Bone is known to bond to the surface of Ti alloys. This can lead to re-fracture of newly repaired bone during operations to remove the implants, however bone does not bond to Zr-based alloys. The inhibition of bone conduction on the surface of Zr-based alloys is thought to be due to the presence of a thin layer of zirconia (ZrO2) on the surface. The purpose of the present study was to synthesize bioinert films, including ZrO2 on pure Ti surfaces. In vitro apatite (HAp) formation and in vivo bone conduction in the tibiae of rats on the films were also investigated.

Commercial purity Ti was chemically treated with aqueous H2O2/HNO3 at 353 K for 20 min. The disks were hydrothermally treated with aqueous ZrOCl2/NH3/C6H8O7 (citric acid) in an autoclave at 453 K for 12 h. Simulated body fluid (SBF) immersion test and implantation into tibiae of rats were carried out.

In the hydrothermal treatment with aqueous ZrOCl2/NH3, the surface product was anatase-type TiO2. On the other hand, when citric acid was added the surface of Ti was covered homogeneously with a TiO2–ZrO2 composite film though the amount of ZrO2 was very small. HAp began to form on the non-modified Ti and TiO2 surfaces after 6 days and 4 days immersion in Hank’s solution, respectively. On the surfaces of TiO2–ZrO2, the presence of precipitates was confirmed after 6-8 days. The HAp formation was suppressed on the surfaces of TiO2–ZrO2.The present TiO2-ZrO2 surface also showed significantly lower bone-implant contact ratio in cortical bone compared with TiO2.

Keywords

biomaterialbonehydrothermal
Type
Research Article
Information
MRS Online Proceedings Library (OPL) , Volume 1418: Symposium LL/MM – Gels and Biomedical Materials , 2012 , mrsf11-1418-mm03-07
Copyright
Copyright © Materials Research Society 2012

Access options

Get access to the full version of this content by using one of the access options below. (Log in options will check for institutional or personal access. Content may require purchase if you do not have access.)

References

REFERENCES

1. Hanawa, T., Hiromoto, S., Asami, K., Okuno, O. and Asaoka, K., Mater. Trans. 43, 3000 (2002).CrossRefGoogle Scholar
2. Saldaña, L., Méndez-Vilas, A., Jiang, L., Multigner, M., González-Carrasco, J.L., Pérez-Prado, M.T., González-Martín, M.L., Munuera, L. and Vi laboa, N., Biomaterials 28, 4343 (2007).CrossRefGoogle Scholar
3. Thomsen, P., Larsson, C. and Ericson, L.E., J. Mater. Sci: Mater. In Medicine 8, 653 (1997).Google Scholar
4. Uchida, M., Kim, H.M., Miyaji, F., Kokubo, T. and Nakamura, T., Biomaterials 23, 313 (2002).CrossRefGoogle Scholar
5. Kuroda, D., Niinomi, M., Morinaga, M., Kato, Y. and Yashiro, T., Mater. Sci. Eng. A 263, 193 (1999).Google Scholar
6. Niinomi, M., J. the Mechanical Behavior of Biomedical Materials 1, 30 (2008).CrossRefGoogle Scholar
7. Ikeda, M., Komatsu, S., Sugimoto, T. and Hasegawa, M., Mater. Sci. Eng. A 243, 140 (1998).CrossRefGoogle Scholar
8. Ueda, M., Matsunaga, R., Ikeda, M. and Ogawa, M., Mater. Trans. 49, 1706 (2008).CrossRefGoogle Scholar
9. Ueda, M., Ikeda, M. and Ogawa, M., Mater. Sci. Eng. C 29, 994 (2009).CrossRefGoogle Scholar
10. Ueda, M., Sasaki, Y., Ikeda, M. and Ogawa, M., Mater. Trans. 50, 2104 (2009).CrossRefGoogle Scholar
11. Ueda, M., Sasaki, Y., Ikeda, M., Ogawa, M., Fujitani, W. and Nakano, T., Mater. Trans. 50, 2147 (2009).CrossRefGoogle Scholar
12. Tsuchiya, H., Macak, J.M., Müller, L., Kunze, J., Müller, F., Greil, Peter, Virtanen, S. and Schmuki, P., J. Biomed. Mater. Res. Part A 77, 534 (2006).CrossRefGoogle Scholar