Hostname: page-component-586b7cd67f-t7czq Total loading time: 0 Render date: 2024-11-29T07:18:47.881Z Has data issue: false hasContentIssue false
  • English
  • Français

Design of Epoxy Encapsulating Compounds for Highly Reliable Surface Mounting Semiconductor Devices

Published online by Cambridge University Press:  21 February 2011

Toshiaki Ishii ,
R. Moteki ,
A. Nagai ,
S. Eguchi  and
M. Ogata
Toshiaki Ishii
Affiliation:
Hitachi Research Laboratory, Hitachi Ltd., 7–1–1 Omika, Hitachi, Ibaraki 319-12, Japan
R. Moteki
Affiliation:
Hitachi Research Laboratory, Hitachi Ltd., 7–1–1 Omika, Hitachi, Ibaraki 319-12, Japan
A. Nagai
Affiliation:
Hitachi Research Laboratory, Hitachi Ltd., 7–1–1 Omika, Hitachi, Ibaraki 319-12, Japan
S. Eguchi
Affiliation:
Hitachi Research Laboratory, Hitachi Ltd., 7–1–1 Omika, Hitachi, Ibaraki 319-12, Japan
M. Ogata
Affiliation:
Minamiyuki Works, Hitachi Chemical Co., Ltd., 1772–1 Kanakubo, Yuki, Ibaraki, 307, Japan
Get access

Abstract

One of the most important subjects for semiconductor packages is preventing cracks which occur when the entire package is exposed to a soldering temperature of 215 to 260°C in the surface mounting technology. Cracking, as seen during temperature cycling tests is also a problem to be addressed. This paper reports the design of epoxy encapsulating compounds for highly reliable semiconductor devices which require the following properties: (1) toughness of matrix resin, (2) low moisture absorption, (3) high adhesion to insertions, and (4) reduction of thermal stress. The moisture absorption was lowered and the toughness was improved by using hydrophobic epoxy resins and high filler loading. The latter reduced the thermal stress, and it was effective for lowering the moisture absorption and increasing the fracture toughness of molding compounds. The reliability tests results were also considered in terms of physical properties of molding compounds.

Type
Research Article
Information
MRS Online Proceedings Library (OPL) , Volume 390: Symposium S – Electronic Packaging Materials Science VIII , 1995 , 71
Copyright
Copyright © Materials Research Society 1995

Access options

Get access to the full version of this content by using one of the access options below. (Log in options will check for institutional or personal access. Content may require purchase if you do not have access.)

References

REFERENCES

1. Manzione, L. T., in Plastic Packaging of Microelectronic Devices, (Van Nostrand Reinhold, New York, 1990).Google Scholar
2. Ogata, M., et al., Netukoukasei Jushi 13, 235 (1992).Google Scholar
3. Kinlock, A. J. and Young, R. J., in Fracture Behavior of Polymers, (Applied Science, London, 1975).Google Scholar
4. Landel, R. F., Moser, B. G., and Bauman, A. J., in Proc. 4th Internat. Congr. Rheol., Part 2, Lee, E. H., Ed. (Interscience, New York, 1965).Google Scholar
5. Ouchiyama, N. and Tanaka, T., Ind. Eng. Chem. Fundam. 23, 490(1984).Google Scholar
6. Ishai, O. and Cohen, L. J., Int. J. Mech. Sci., 9, 539(1967).Google Scholar
7. Fahmy, A. A. and Ragai, A. N., J. Am. Ceramics Soc., 40, 351(1957).Google Scholar