Hostname: page-component-586b7cd67f-2plfb Total loading time: 0 Render date: 2024-11-30T10:34:48.832Z Has data issue: false hasContentIssue false
  • English
  • Français

Additive manufacturing of metal matrix composites via nanofunctionalization

Published online by Cambridge University Press:  21 May 2018

John H. Martin Open the ORCID record for John H. Martin [Opens in a new window] ,
Brennan D. Yahata ,
Eric C. Clough ,
Justin A. Mayer ,
Jacob M. Hundley  and
Tobias A. Schaedler
John H. Martin*
Affiliation:
HRL Laboratories LLC, Malibu, California 90265-4797, USA
Brennan D. Yahata
Affiliation:
HRL Laboratories LLC, Malibu, California 90265-4797, USA
Eric C. Clough
Affiliation:
HRL Laboratories LLC, Malibu, California 90265-4797, USA
Justin A. Mayer
Affiliation:
HRL Laboratories LLC, Malibu, California 90265-4797, USA
Jacob M. Hundley
Affiliation:
HRL Laboratories LLC, Malibu, California 90265-4797, USA
Tobias A. Schaedler
Affiliation:
HRL Laboratories LLC, Malibu, California 90265-4797, USA
*
Address all correspondence to John H. Martin at [email protected]
Get access

Abstract

A novel, alloy-agnostic, nanofunctionalization process has been utilized to produce metal matrix composites (MMCs) via additive manufacturing, providing new geometric freedom for MMC design. MMCs were produced with the addition of tungsten carbide nanoparticles to commercially available AlSi10Mg alloy powder. Tungsten carbide was chosen due to the potential for coherent crystallographic phases that were identified utilizing a lattice-matching approach to promote wetting and increase dislocation interactions. Structures were produced with evenly distributed strengthening phases leading to tensile strengths >385 MPa and a 50% decrease in wear rate over the commercially available AlSi10Mg alloy at only 1 vol% loading of tungsten carbide.

Type
Research Letters
Information
MRS Communications , Volume 8 , Issue 2 , June 2018 , pp. 297 - 302
Check for updates
Copyright
Copyright © Materials Research Society 2018 

Access options

Get access to the full version of this content by using one of the access options below. (Log in options will check for institutional or personal access. Content may require purchase if you do not have access.)

References

1.Kainer, K.U.: In Metal Matrix Composites, edited by Kainer, K.U. (Wiley-VCH Verlag GmbH & Co. KGaA, Darmstadt, Germany, 2006), pp. 1–54.Google Scholar
2.Ibrahim, I.A., Mohamed, F.A., and Lavernia, E.J.: Particulate reinforced metal matrix composites – a review. J. Mater. Sci. 26(5), 1137–1156 (1991).Google Scholar
3.González-Doncel, G. and Fernández, R.: Comments on “creep behavior of in situ TiCP/2618 aluminum matrix composite”. Mater. Sci. Eng. A 527(13–14), 3288–3292 (2010).Google Scholar
4.Ramesh, C.S. and Ahamed, A.: Friction and wear behaviour of cast Al 6063 based in situ metal matrix composites. Wear 271(9–10), 1928–1939 (2011).CrossRefGoogle Scholar
5.Tomac, N., Tannessen, K., and Rasch, F.O.: Machinability of particulate aluminium matrix composites. CIRP Ann. 41(1), 55–58 (1992).CrossRefGoogle Scholar
6.Dai, D. and Gu, D.: Tailoring surface quality through mass and momentum transfer modeling using a volume of fluid method in selective laser melting of TiC/AlSi10Mg powder. Int. J. Mach. Tools Manuf. 88, 95–107 (2015).CrossRefGoogle Scholar
7.Thomas, A.T., Parameshwaran, R., Muthukrishnan, A., and Kumaran, M.A.: Development of feeding and stirring mechanisms for stir casting of aluminium matrix composites. Proc. Mater. Sci. 5, 1182–1191 (2014).Google Scholar
8.Ye, H., Liu, X.Y., and Hong, H.: Fabrication of metal matrix composites by metal injection molding – a review. J. Mater. Process. Technol. 200(1–3), 12–24 (2008).Google Scholar
9.Gofrey, T.M.T., Goodwin, P.S., and Ward-Close, C.M.: Titanium particulate metal matrix composites – reinforcement, production methods, and mechanical properties. Adv. Eng. Mater. 2(3), 85–91 (2000).Google Scholar
10.Hashim, J., Looney, L., and Hashmi, M.S.J.: Metal matrix composites: production by the stir casting method. J. Mater. Process. Technol. 92–93, 1–7 (1999).CrossRefGoogle Scholar
11.Das, S., Bourell, D.L., and Babu, S.S.: Metallic materials for 3D printing. MRS Bull. 41(10), 729–741 (2016).Google Scholar
12.Martin, J.H., Yahata, B.D., Hundley, J.M., Mayer, J.A., Schaedler, T.A., and Pollock, T.M.: 3D printing of high-strength aluminium alloys. Nature 549(7672), 365–369 (2017).Google Scholar
13.Han, G., Zhang, W., Zhang, G., Feng, Z., and Wang, Y.: High-temperature mechanical properties and fracture mechanisms of Al–Si piston alloy reinforced with in situ TiB2 particles. Mater. Sci. Eng. A 633, 161–168 (2015).Google Scholar
14.Xiao, P., Gao, Y., Yang, C., Liu, Z., Li, Y., and Xu, F.: Microstructure, mechanical properties and strengthening mechanisms of Mg matrix composites reinforced with in situ nanosized TiB2 particles. Mater. Sci. Eng. A 710, 251–259 (2017).Google Scholar
15.Hull, D. and Bacon, D.J.: Introduction to Dislocations, 4th ed. (Butterworth-Heinemann, Oxford, England, 2001), pp. 225, 356, 200–300.Google Scholar
16.Nan, C.W. and Clarke, D.R.: The influence of particle size and particle fracture on the elastic/plastic deformation of metal matrix composites. Acta Mater. 44(9), 3801–3811 (1996).CrossRefGoogle Scholar
17.Bharath, V., Nagaral, M., Auradi, V., and Kori, S.A.: Preparation of 6061Al-Al2O3 MMC's by stir casting and evaluation of mechanical and wear properties. Proc. Mater. Sci. 6(Icmpc), 1658–1667 (2014).Google Scholar
18.Stefanescu, D.M.: Science and Engineering of Casting Solidification (Springer International Publishing, Cham, Switzerland, 2015), pp. 157–194.Google Scholar
19.Acharya, R., Sharon, J.A., and Staroselsky, A.: Prediction of microstructure in laser powder bed fusion process. Acta Mater. 124, 360–371 (2017).CrossRefGoogle Scholar
20.Kurz, W. and Fisher, D.J.: Fundamentals of Solidification (Trans Tech Publications Ltd., Aedermannsdorf, Switzerland, 1998).Google Scholar
21.Scipioni Bertoli, U., Wolfer, A.J., Matthews, M.J., Delplanque, J.-P.R., and Schoenung, J.M.: On the limitations of volumetric energy density as a design parameter for selective laser melting. Mater. Des. 113, 331–340 (2017).Google Scholar
22.Ozaki, Y. and Zee, R.H.: Investigation of thermal and hydrogen effects on emissivity of refractory metals and carbides. Mater. Sci. Eng. A 202(1–2), 134–141 (1995).CrossRefGoogle Scholar
23.Matthews, M.J., Guss, G., Khairallah, S.A., Rubenchik, A.M., Depond, P.J., and King, W.E.: Denudation of metal powder layers in laser powder bed fusion processes. Acta Mater. 114, 33–42 (2016).Google Scholar
24.CL 30AL/CL 31AL Aluminum Alloys (Concept Laser, Hoffmann Innovation Group, 2012), pp. 1–3.Google Scholar
25.Rosenthal, I., Stern, A., and Frage, N.: Microstructure and mechanical properties of AlSi10Mg parts produced by the laser beam additive manufacturing (AM) technology. Metallogr. Microstruct. Anal. 3(6), 448–453 (2014).CrossRefGoogle Scholar
Supplementary material: File

Martin et al. supplementary material

Martin et al. supplementary material 1

Download Martin et al. supplementary material(File)
File 1.1 MB