Hostname: page-component-cd9895bd7-fscjk Total loading time: 0 Render date: 2024-12-23T13:16:05.261Z Has data issue: false hasContentIssue false
  • English
  • Français

Microstructural and Mechanical Characterization of Autogenous GTAW Weld in High-Manganese Austenitic Steel Ti-Containing with Thermal Analysis

Published online by Cambridge University Press:  11 January 2019

V. García-García ,
I. Mejía  and
F. Reyes-Calderón
V. García-García
Affiliation:
Instituto de Investigaciones Metalúrgicas, Universidad Michoacana de San Nicolás de Hidalgo, Edificio “U-5” Ciudad Universitaria, 58066Morelia, Michoacán, México. E-mail: [email protected], [email protected]
I. Mejía*
Affiliation:
Instituto de Investigaciones Metalúrgicas, Universidad Michoacana de San Nicolás de Hidalgo, Edificio “U-5” Ciudad Universitaria, 58066Morelia, Michoacán, México. E-mail: [email protected], [email protected]
F. Reyes-Calderón
Affiliation:
Departamento de Metalmecánica, Instituto Tecnológico de Morelia, Av. Tecnológico 1500, 58120Morelia, Michoacán, México.
*
*(Email: [email protected])
Get access

Abstract

The welding heat input has been pointed out as a main limiting factor for TWinnig Induced Plasticity (TWIP) steel weldability. Scarce research works have been focused on the study of application and effects of the Gas Tungsten Arc Welding (GTAW) process in the TWIP steel, especially in higher thickness plate. In this research work was conducted a detailed analysis of a butt weld joint performed in plates of TWIP steel microalloyed with titanium (TWIP-Ti) of 6.3 mm thickness. The autogenous GTAW process with low heat input was applied. The analysis considered grain size measurements, second phases identification, post-weld mechanical properties (microhardness) and the welding thermal field. A Finite Element Model (FEM), validated through experimental results, allowed correlating metallurgical results with the thermal field. Likewise, the phases prediction carried out by means of JMatPro 9.0 software during solidification process as well as the estimation of particle precipitation were in good agreement with the experimental results. These predictive diagrams were calculated taking into account the TWIP-Ti steel chemical composition, the grain size measured in critical weld regions and experimental cooling rates. The low heat input improved the microstructural conditions in the heat affected zone (HAZ) whose average grain size and precipitate particles, like (C, N)Ti, promoted good mechanical properties as compared to the base material (as-solution condition). Some particles like Al2O3 y MnS produced microporosities in the HAZ. Despite this, the weld joint did not present hot cracking in the FZ-HAZ interface.

Keywords

steelweldingsimulation
Type
Articles
Information
MRS Advances , Volume 3 , Issue 64: International Materials Research Congress XXVII , 2018 , pp. 3963 - 3969
Copyright
Copyright © Materials Research Society 2019 

Access options

Get access to the full version of this content by using one of the access options below. (Log in options will check for institutional or personal access. Content may require purchase if you do not have access.)

References

REFERENCES

De Cooman, B. C., Estrin, Y., Kim, S. K., Acta Materialia, 142 (2018).CrossRefGoogle Scholar
Frommeyer, G., Brüx, U., Neumann, P., ISIJ International, 43 (2003).CrossRefGoogle Scholar
Yoo, J., Han, K., Park, Y., Choi, J., Lee, C., Science and Technology of Welding and Joining, 19 (2014).CrossRefGoogle Scholar
Mújica, L., Weber, S., Theisen, W., Scripta Materialia, 66 (2012).Google Scholar
De Cooman, B. C., Kwon, O., Chin, K.G., Materials Science and Technology, 28 (2012).CrossRefGoogle Scholar
Mujica, L., Weber, S., Thomy, C., Vollertsen, F., Science and Technology of Welding & Joining,14 (2009).CrossRefGoogle Scholar
Saha, D. C., Chang, I., Y. D, Materials Characterization, 93 (2014).CrossRefGoogle Scholar
Wei, Y. H., Hou, L. F., Bin, Y. A. N, Journal of Iron and Steel Research International, 21 (2014).CrossRefGoogle Scholar
ASTM, ASTM International, West Conshohocken, PA http://dx.doi.org/10.1520/E0112-10 (2009).CrossRefGoogle Scholar
Lu, S. P., Qin, M. P., Dong, W. C., Journal of Materials Processing Technology, 213 (2013).Google Scholar
Salas-Reyes, A.E., Mejía, I., Bedolla-Jacuinde, A., Boulaajaj, A., Calvo, J., Cabrera, J.M., Materials Science and Engineering A, 611 (2014).CrossRefGoogle Scholar
Steenken, B., Rezende, J. L., Senk, D., Materials Science and Technology, 33 (2017).CrossRefGoogle Scholar
Humphreys, F. J., Hatherly, M., Recrystallization and Related Annealing Phenomena, second ed., Elsevier, UK, 2004.Google Scholar