Hostname: page-component-78c5997874-m6dg7 Total loading time: 0 Render date: 2024-11-06T03:47:35.352Z Has data issue: false hasContentIssue false
  • English
  • Français

The Influence of Binders on Interfacial Failure in Sapphire Fiber-reinforced NiAl Composites

Published online by Cambridge University Press:  31 January 2011

Jeffrey I. Eldridge ,
Donald R. Wheeler ,
Randy R. Bowman  and
Andras Korenyi-Both
Jeffrey I. Eldridge
Affiliation:
NASA Lewis Research Center, Cleveland, Ohio 44135
Donald R. Wheeler
Affiliation:
NASA Lewis Research Center, Cleveland, Ohio 44135
Randy R. Bowman
Affiliation:
NASA Lewis Research Center, Cleveland, Ohio 44135
Andras Korenyi-Both
Affiliation:
Gilcrest, Cleveland, Ohio 44135
Get access

Abstract

The influence of organic binders on fiber/matrix bonding during the powder metallurgy fabrication of sapphire fiber-reinforced NiAl matrix composites (sapphire/NiAl) was investigated. One composite panel was fabricated using a poly(methyl methacrylate) (PMMA) fiber binder and a teflon matrix powder binder; another panel was fabricated by binderless powder metallurgy consolidation. The effect of the binders on fiber/matrix bonding was evaluated by fiber push-out testing from room temperature to 900 °C. Examination of mating fiber and matrix-trough fracture surfaces by scanning electron microscopy (SEM) and Auger electron spectroscopy (AES) revealed differences in interfacial morphology and chemistry, depending on the use of binders in fabrication. The primary difference between the two composites was the much higher concentration of carbon at the fiber/matrix interface in sapphire/NiAl fabricated with binders. This carbon residue from binder burnout prevented clean contact between the sapphire fiber and NiAl matrix surfaces, resulting in a weak, thermomechanically clamped fiber/matrix interface, in contrast to the stronger, less temperature dependent, interfacial bonding observed without binders.

Type
Articles
Information
Journal of Materials Research , Volume 12 , Issue 8 , August 1997 , pp. 2191 - 2197
Copyright
Copyright © Materials Research Society 1997

Access options

Get access to the full version of this content by using one of the access options below. (Log in options will check for institutional or personal access. Content may require purchase if you do not have access.)

References

1.Bowman, R. R., in Intermetallic Matrix Composites II, edited by Miracle, D. B., Anton, D. L., and Graves, J. A. (Mater. Res. Soc. Symp. Proc. 273, Pittsburgh, PA, 1992), p. 145.Google Scholar
2.Draper, S. L. and Locci, I. E., J. Mater. Res. 9, 1397 (1994).CrossRefGoogle Scholar
3.Wang, L., Xu, K., Bowman, R. R., and Arsenault, R. J., Metall. Mater. Trans. 26A, 897 (1995).CrossRefGoogle Scholar
4.Pickens, J. W., Noebe, R. D., Watson, G. K., Brindley, P. K., and Draper, S. L., Fabrication of Intermetallic Matrix Composites by the Powder Cloth Method, NASA Technical Memorandum 102060 (1989).Google Scholar
5.Eldridge, J. I., Desktop Fiber Push-Out Apparatus, NASA Technical Memorandum 105341 (1991).Google Scholar
6.Eldridge, J. I. and Ebihara, B. T., J. Mater. Res. 9, 1035 (1994).CrossRefGoogle Scholar
7.Brennan, J. J., in Tailoring Multiphase and Composite Ceramics, edited by Tressler, R. E.et al. (Materials Science Research 20, Plenum Press, New York, 1986), p. 549.CrossRefGoogle Scholar
8.Sherman, R., Surf. Interf. Anal. 10, 23 (1987).CrossRefGoogle Scholar
9.Palmberg, P. W., Riach, G. E., Weber, R. E., and MacDonald, N. C., Handbook of Auger Electron Spectroscopy (Physical Electronics Industries, Edina, MN, 1972).Google Scholar
10.Moose, C. A., Koss, D. A., and Hellmann, J. R., in Intermetallic Matrix Composites, edited by Anton, D. L., Martin, P. L., Miracle, D. B., and McMeeking, R. (Mater. Res. Soc. Symp. Proc. 194, Pittsburgh, PA, 1990), p. 293.Google Scholar