Hostname: page-component-78c5997874-v9fdk Total loading time: 0 Render date: 2024-11-09T05:31:06.942Z Has data issue: false hasContentIssue false

Alloys that form conductive and passivating oxides for proton exchange membrane fuel cell bipolar plates

Published online by Cambridge University Press:  03 March 2011

Neil Aukland
Affiliation:
Delphi Research Laboratories, Delphi Corporation, 51786 Shelby Parkway, Shelby Township, Michigan 48315
Abdellah Boudina
Affiliation:
Delphi Research Laboratories, Delphi Corporation, 51786 Shelby Parkway, Shelby Township, Michigan 48315
David S. Eddy
Affiliation:
Delphi Research Laboratories, Delphi Corporation, 51786 Shelby Parkway, Shelby Township, Michigan 48315
Joseph V. Mantese
Affiliation:
Delphi Research Laboratories, Delphi Corporation, 51786 Shelby Parkway, Shelby Township, Michigan 48315
Margarita P. Thompson
Affiliation:
Delphi Research Laboratories, Delphi Corporation, 51786 Shelby Parkway, Shelby Township, Michigan 48315
Simon S. Wang*
Affiliation:
Delphi Research Laboratories, Delphi Corporation, 51786 Shelby Parkway, Shelby Township, Michigan 48315
*
a) Address all correspondence to this author.email: [email protected]
Get access

Abstract

During the operation of proton exchange membrane (PEM) fuel cells, a high-resistance oxide is often formed on the cathode surface of base metal bipolar plates. Over time, this corrosion mechanism leads to a drop in fuel cell efficiency and potentially to complete failure. To address this problem, we have developed alloys capable of forming oxides that are both conductive and chemically stable under PEM fuel cell operating conditions. Five alloys of titanium with tantalum or niobium were investigated. The oxides were formed on the alloys by cyclic voltammetry in solutions mimicking the cathode- and anode-side environment of a PEM fuel cell. The oxides of all tested alloys had lower surface resistance than the oxide of pure titanium. We also investigated the chemical durability of Ti–Nb and Ti–Ta alloys in more concentrated solutions beyond those typically found in PEM fuel cells. The oxide films formed on Ti–Nb and Ti–Ta alloys remained conductive and chemically stable in these concentrated solutions. The stability of the oxide films was evaluated; Ti alloys having 3% Ta and Nb were identified as potential candidates for bipolar plate materials.

Type
Articles
Copyright
Copyright © Materials Research Society 2004

Access options

Get access to the full version of this content by using one of the access options below. (Log in options will check for institutional or personal access. Content may require purchase if you do not have access.)

References

REFERENCES

1Larminie, J. and Dicks, A., Fuel Cell Systems Explained (John Wiley & Sons, Chichester, U.K., 2000).Google Scholar
2Blomen, L.J.M.J. andMugerwa, M.N.,Fuel Cell Systems (Plenum Press, New York, 1993).CrossRefGoogle Scholar
3Hodgson, D.R., May, B., Adcock, P.L. and Davies, D.P.: New lightweight bipolar plate system for polymer electrolyte membrane fuel cells. J. Power Sources 96, 233 (2001).CrossRefGoogle Scholar
4Murphy, O.J., Cisar, A. and Clarke, E.: Low-cast light weight high power density PEM fuel cell stack. Electrochimica Acta 43, 3829 (1998).CrossRefGoogle Scholar
5Makkus, R.C., Janssen, A.H.H., Bruijn, F.A. and Mallant, R.K.A.M.: Use of stainless steel for cost competitive bipolar plates in the SPFC. J. Power Sources 86, 274 (2000).CrossRefGoogle Scholar
6Cunningham, N., Guay, D., Dodelet, J.P., Meng, Y., Hlil, A.R. and Hay, A.S.: New materials and procedures to protect metallic PEM fuel cell bipolar plates. J. Electrochem. Soc. 149 A905 (2002).CrossRefGoogle Scholar
7Hornung, R. and Kappelt, G.: Bipolar plate materials development using Fe-based alloys for solid polymer fuel cells. J. Power Sources 72, 20 (1998).CrossRefGoogle Scholar
8Philpot, K.A., Ikuma, Y., Miller, G.R. and Gordon, R.S.: High temperature steady-state creep of polycrystalline rutile, pure and doped with tantalum. J. Mater. Sci. 18, 1698 (1983).Google Scholar
9Miller, R., Johnson, O.W.: The Sintering of Conductive: A Model System for Sintering Electronic Ceramics in Processing of Crystalline Ceramics, edited by Palmor, H. III, Davis, R.F., and Hare, T.M. (Plenum Press, New York, 1978).Google Scholar
10Weast, R.C., CRC Handbook of Chemistry and Physics, 51st ed. (The Chemical Rubber Co., OH, 1970).Google Scholar
11Hansen, M.,Constitution of Binary Alloys (McGraw-Hill Book Co., New York, 1958).CrossRefGoogle Scholar
12Levin, E.M., Robbins, C.R., and McMurdie, H.F.,Phase Diagrams for Ceramists (The American Ceramic Society, OH, 1964).Google Scholar
12Levin, E.M., Robbins, C.R., and McMurdie, H.F.,Phase Diagrams for Ceramists 1969 supplement (The American Ceramic Society, OH, 1969).Google Scholar
14Bard, J.A. and Faulkner, L.R., Electrochemical Methods, Fundamentals and Applications,2nd ed. (John Wiley & Sons, New York, 2000).Google Scholar