Reconfigurable intelligent surfaces (RISs) enhance the performance of wireless communication networks, particularly within millimeter wave (mm-Wave) bands. When a line-of-sight link is not strong enough or is fully blocked. The location of RIS has a significant impact on the RIS’s wireless channel and system performance. A wireless communication model has been proposed in a mm-Wave environment supported by RIS. The proposed model contains one transmitter and five users at the receiving end. Due to the small distance between users, there is interference between them and the received signal-to-interference-plus-noise ratio (SINR) decreases. Three RISs separated by different interspace distances were proposed to serve users at various distances from the transmitter to reduce inter-user interference. The simulation results showed that increasing the distance between the RIS site and the TX-User line served a larger number of users, and the three heights of the RIS provided a coverage range domain complementary to each other for different user sites. The improvement percentages in SINR for the second and third RIS are 48.46% and 77.38%, respectively. Enlarging the size of the RIS only increases the signal capacity and does not affect the coverage range domain of the single RIS.

A long-range, compact, wideband Ultra High Frequency (UHF) radio frequency identification (RFID) tag is proposed. The design features a triangular patch, designed to achieve wideband impedance matching. The tag exhibit −10 dB bandwidth from 753 to 917 MHz with a substrate thickness of 1.575 mm. The overall size of the tag is 121 × 30 × 1.575 mm3. The gain and bandwidth for varying substrate thickness is investigated. Further, two parasitic strips are designed alongside the patch to operate the tag more effectively at Federal Communications Commission (FCC) band in simultaneous with European Telecommunications Standards Institute (ETSI) band with increased read range. With parasitic strips, the tag exhibits −10 dB bandwidth from 766.5 to 896.5 MHz and 905 to 943.6 MHz which covers the bandwidth requirements in Europe, Asia, and North America. A prototype of the proposed tag is fabricated and experimentally tested with the RFID Higgs 4 IC. The tag provides a read range of over 14 m in 865–870 MHz and 13 m in 902–928 MHz when the tag is operated in free space and a read range of over 10.2 m in 865–870 MHz range and 10.3 m in 902–928 MHz range when mounted on a metallic surface of size of 200 × 200 m2 . The performance parameters of the designed tag are also compared with some commercially available designs.

In this paper, a large, compact array antenna that can be expanded in the 2-D plane is proposed for near-field radio frequency identification applications. By the introduction of the fractal structure and corner joint method, the array is easy to expand in the 2-D plane. An antenna element can be divided into a dozen or so loops, and traveling wave distribution makes sure that every loop is excited in a time period. So that a strong and uniform magnetic field could be generated in a large area. As a proof of concept, array antennas with $1 \times 8$, $2 \times 4$, and $3 \times 3$ elements are designed, fabricated, and measured. The measured bandwidth of the antennas covers the entire Chinese standard. Reading distances of the proposed large array antennas achieved up to 57 mm. Results show that the proposed antenna could realize flexibility and extendibility in a large area with stable and uniform magnetic field distribution.

In this article, a qualitative work has been carried out based on airborne pulsed Doppler (PD) RF sensor consist of its operational requirements in terms of phase noise modeling and associated contributing factors. Precise and efficient theoretical modeling of phase noise requirement for airborne-PD radar or long-range RF sensor is presented. This work also emphasis on the limitation of conventional phase noise modeling practices used for PD RF sensor. An improved equation has been derived for accurate phase noise estimation considering the range correlation effect and inline flicker contribution on residual phase noise requirement. Random vibrations causes increase in phase noise level around low frequency offsets region in local oscillator. The proposed phase noise model is efficient enough to counter phase noise degradation at lower frequency offsets. The proposed model is also experimentally validated. Improved modeling offers benefit in reducing the stringent RF sensor phase noise specifications at close-in frequency offsets using range correlation effect and precise inclusion of inline flicker contribution. Present work can be used to mitigate random vibration effects at close-in phase noise offsets, which avoids complex stabilization practices and stringent oscillator design phase noise specification.

This paper presents a vertically folded gap waveguide filter for use as the filter element for each antenna in an array of slotted waveguide antennas, at W-band. Loaded gap-waveguide resonators are used to reduce the footprint of the filter, and the filter is vertically folded to reduce the length. New input and output transitions are proposed, as well as inter-resonator coupling structures that conform to the basic gap-waveguide structure. A 7th order filter with a bandwidth of 10 GHz and a center frequency of 101 GHz is designed to meet geometric constraints of a transmitter system. A sensitivity analysis was performed on the structure to determine the required manufacturing tolerances. The filter was manufactured and measured yielding 10 dB of return loss in the passband and a detuning of the passband by 1 GHz. The return loss at 88 GHz peaked due to deviations in manufactured gap height in the gap waveguide. Deviations from the simulated response were accounted for with a parameter extraction from the measured results.

A novel high-selectivity ultra-wideband (UWB) balanced bandpass filter (BPF) with harmonic suppression characteristics is proposed. The differential-mode UWB passband is constructed using quarter-wavelength asymmetrical parallel-coupled transmission lines, resulting in sharp filtering selectivity, while common-mode noises are suppressed by loading the T-type stubs. A simple design method of integrating bandstop filter branches into the BPF for third harmonic suppression without increasing the circuit size is described and confirmed. A planar high-selectivity balanced BPF prototype is manufactured and measured at 2.6 GHz with a measured 3-dB fractional bandwidth of 108% to validate the framework principle. More importantly, with third harmonic suppression characteristics, the measured out-of-band rejection is more than 20 dB, spanning 4.35 GHz until 12.4 GHz.

In order to recover the magnetic energy that leaks from an induction cooktop, this study suggests a straightforward and cost-effective magnetic-field energy harvester (MFEH) circuit. With the aid of the intended circuitry, the acquired magnetic energy is transformed into DC electrical energy. We harvested the magnetic-field energy (MFE) from the induction cooktop at various heights and locations of the energy harvesting coil. With a load resister of 46.6 Ω and a capacitance of 1 mF, the developed MFEH circuit, when positioned 2 cm beneath the cooktop, can capture an average DC power of 1936 mW. Placing the energy-harvesting coil 7.5 cm beneath the induction cooktop lowers the power output to 142 mW. For a range of load resister values, the MFE gathered at various locations along the energy harvesting coils is examined. Batteries can be used to store the gathered energy for later use. Additionally, the suggested device is shown to be capable of wirelessly powering low-power Internet of things devices and charging mobile devices. The suggested device differs from the previously published magnetic harvesting circuits due to the induction cooktop’s superior performance and capacity to gather MFE.

This paper proposes a compact coplanar waveguide-fed slot antenna for ultra-wideband wearable applications, featuring six notch bands. The antenna utilizes a flexible liquid crystal polymer substrate with a thickness of 0.1 mm. The antenna achieves six band-notched characteristics by incorporating a split concentric ring etched on the radiating patch and L-shaped branches loaded on the ground plane. The proposed flexible antenna has dimensions of 30 × 30 mm2(0.65λ0*0.65λ0,λ0 is the free space wavelength at 6.5 GHz.). Measurement results show an impedance bandwidth ranging from 2.37 to 13.7 GHz and a fractional bandwidth of 134%. The notch bands cover 2.9–3.77 GHz for WiMAX applications, 4.14–4.9 GHz for the ARN band, 5.09–5.55 GHz for the WLAN downlink band, 5.86–6.46 GHz for the C-band uplink band, 6.66–7.39 GHz for the C-band/INSAT/super-extended band, and 7.93–8.43 GHz for ITU-8 GHz. The maximum gain in the operating band is 6.5 dBi. The performances of the flexible antenna are analyzed under bending conditions. The ANSYS HFSS electromagnetic simulator was used for the design and simulation of the proposed antenna. The flexible antenna is suitable for wearable applications.

This paper outlines the design of a six-element multiple-input–multiple-output (MIMO) antenna with pattern diversity for industrial scientific medical (ISM)/5G-enabled wireless body area networks (WBANs). Within the MIMO configuration, each element has a quasi-yagi antenna configuration implemented on an ultrathin microwave laminate. The proposed quasi-yagi antenna has a small form factor of 25 × 25 mm, featuring a dipole-like radiator excited through a microstrip-line to tapered slot-line transition. The antenna’s radiators are patterned to ensure a dual-narrow impedance bandwidth. The conventional strip-line director in the planar yagi is replaced with a semicircular loop-like director, enhancing directional radiation patterns. This proposed flexible antenna offers versatile functionality by operating at both ISM standards of 2.45 GHz and the 5G wireless local area network standard at 3.5 GHz. The quasi-yagi elements are strategically distributed in a hexagonal formation to construct the six-element MIMO scheme with pattern diversity, resulting in a tangential radiation pattern suitable for on-body communication. Following fabrication, the prototype MIMO antenna’s simulation results are validated through real-time measurements. The proposed antenna exhibits an average gain exceeding 3.5 dBi across both operating bands. Furthermore, the proposed MIMO antenna exhibits promising performance metrics suitable for densely cluttered WBAN environments.

A compact, wideband, and high-gain circularly polarized array antenna is proposed based on substrate integrated gap waveguide (SIGW) using sequential rotational phase (SRP). The array antenna consists of four $2\times2$ corner-cutting corner patches and an SIGW-SRP feeding network. The SIGW-SRP feeding network is achieved by utilizing the spatial vector addition property to compensate for phase, aiming to improve the bandwidth and gain. Unlike the traditional SRP feeding network, the proposed feeding scheme is simpler and easier to fabricate, and each port can achieve more stable phase and bandwidth. In addition, benefiting from the surface wave suppression and in-phase reflection property of SIGW, the proposed array antenna has a stable radiation pattern and low cross-polarization covering wideband frequencies. The measured results indicate that the −10-dB impedance bandwidth ranges from 12.2 to 17.3 GHz (34.6%), the 3-dB axial ratio bandwidth ranges from 13.5 to 16.7 GHz (21.2%), and the peak gain is 16 dBic.

In this article, a dual-sense triband circularly polarized modified slot antenna loaded with metamaterial structures such as split-ring resonator and cross strips is proposed. The first resonant frequency is generated using the modified square slot which produces the two degenerative modes required to achieve circular polarization (CP). The corners of slot antenna are extended to obtain the orthogonal modes. The second resonant band is obtained using the single split-ring resonator. Two micro-splits in Split Ring Resonator (SRR) orthogonal to each other produces CP due to electric field generated by the micro-splits. The third resonance band is obtained due to loading of cross strips. The orthogonal phase is adjusted by varying the length of cross strips, so that the CP is achieved. All resonance bands are tuned independently. The measured impedance bandwidth of 31.68%, 4.55%, and 8.6% is obtained in first, second, and third bands respectively. The axial ratio bandwidth of 13.04%, 2.7%, 8.6% and peak gain of 3.8 dBic, 3.9 dBic, 3.7 dBic are obtained respectively. The simulated radiation efficiencies of above 80% is achieved in all bands. The left-hand CP is obtained in first two band as co-polarization and right-hand CP is obtained at the third band as co-polarization with respect to cross-polarization radiation. The cross-polarization of minimum −10 dB is obtained in all three bands. The proposed design is well suitable for the Bluetooth, n78 and n79 5G applications.

This research proposes a low-complexity, low-profile square-shaped quad-band dual-sense circularly polarized (CP) perturbed slot antenna with stepped microstrip feed for C-band radar and satellite applications. The proposed antenna is characterized by characteristic mode analysis. The proposed design has a square-shaped slot with diagonally opposite symmetric rectangular corner extensions. Multiband resonance is achieved by exciting the split ring resonator (SRR), cross strips and annular ring structure using the stepped microstrip line-fed slot radiator. The slot antenna and a metallic ring resonate at 1.64 and 8.2 GHz, respectively, showing left-hand circular polarization response, whereas the SRR and cross strips resonate at 3.6 and 6.6 GHz, respectively, exhibiting right-hand circular polarization radiation at these resonance bands. Hence, the proposed design shows quad-band performance with dual-sense CP behavior. Furthermore, the proposed antenna allows for independent tuning of polarization sense at resonance frequencies. The proposed design uses a low-cost FR-4 material as a substrate of dimensions 60 × 60 × 1.6 mm3. The experimentally measured results are in close agreement with the simulated performance parameters of the prototype.

This work presents the design of a wide-band frequency-selective surface (FSS) with its analysis for the performance enhancement of a microstrip antenna. To demonstrate the concept, a dual-band microstrip antenna is also designed and combined with the proposed FSS to investigate its advantages and performance enhancement capabilities. The proposed FSS is designed for a frequency range of 3.5–6.5 GHz, whereas the designed antenna operates in dual frequency bands of 3.5 and 5 GHz. The combined effect of the antenna and FSS is investigated at 5 GHz for improving the gain of the antenna from 2.8 to 3.2 dBi. The outcome of the measured performance validates that the proposed surface has potential capability for enhancing the gain of an antenna for 5G, WLAN, and Wi-Fi communication.

This letter presents an improved analytical model for analyzing probe-fed microstrip antennas loaded by metallic vias with lumped terminations. The proposed formulation is based on the resonant cavity model and enables efficient analysis of such perturbed radiators for various types of terminations. The model is validated through the analysis of two antennas: one operating in a TM00 mode and the other with four capacitive terminations to produce circular polarization. Moreover, a reconfigurable RHCP/LHCP antenna based on the patch with capacitive terminations has been manufactured and tested, showing a broadside axial ratio below 0.5 dB at 1.575 GHz.

We present continuous Class-F (CCF) and continuous Class-F−1 (CCF−1) power amplifiers (PAs) with compact circuit sizes. The output matching network (OMN) of a continuously harmonic-tuned PA must accommodate varying load impedance conditions across a wide frequency range, spanning from the fundamental frequency up to the 2nd and 3rd harmonic frequencies. This requirement typically leads to LPF-type OMNs with a significant circuit area overhead, thereby limiting the applicability of the broadband PAs. In this paper, we propose utilizing a one-port composite right-/left-handed transmission line to control the harmonic loads, while the fundamental loads are managed by a moderately sized LPF. This resulted in a notable reduction in PA size by nearly an order of magnitude. We demonstrate the effectiveness of this design approach through the fabrication of 2-GHz-band GaN HEMT PAs operating in CCF and CCF−1 modes. While both PAs exhibited high-efficiency (>70%) operational bandwidths at a state-of-the-art level, we also elucidate key design considerations specific to each PA operation mode.