Microwave radars can be used to monitor the internal structure of the snowpack, delivering real-time and non-destructive measurements. Recently, the working principle of an innovative radar architecture able to identify some of the most important snowpack parameters, without external aids, has been demonstrated. A key point of this new architecture is the use of two independent receiving antennas, and one transmitting antenna. This paper presents a comparison between two different implementations, either based on one physical antenna miming two receiving antennas, or based directly on two physical receiving antennas. The different advantages and disadvantages of both solutions are discussed, highlighting the superior accuracy achieved by the implementation based on two physical receiving antennas. Then, this paper also presents the field results achieved by this type of radar architecture, on the grounds of a 5-day experimental campaign that took place in winter 2019 in the Italian Alps on dry snow. The comparison between the radar measurements and the ground truth (manual snowpit analysis, in terms of snowpack depth, dielectric constant, bulk density, and snow water equivalent) is provided. Overall, a root mean square error of around 3.5 cm, 0.05, 27 kg/m3, and 2.5 cm is achieved, respectively.

Near-field to far-field transformations constitute a powerful antenna characterization technique for near-field measurement scenarios. In this paper, a near-field to far-field transformation technique based on multiple spherical wave expansions (SWEs) is presented. Thanks to its iterative matrix inversion nature, the approach performs the transformation of fields measured on arbitrary surfaces. Also, irregular sampling schemes can be incorporated. The proposed algorithm is based on modeling the antenna fields with not one, but several SWEs distributed over its geometry. Due to the high number of SWEs, their truncation number can be arbitrarily reduced. Working with expansions of low order allows us to incorporate the probe correction in the transformation in a very simple way, accepting any type of probe and orientation. Only the probe far-field pattern is used, thus working with its full SWE is avoided. The algorithm is validated using simulated field data as well as measurements of real antennas.

Electromagnetic waves in the microwave and millimeter-wave frequency range are used in non-destructive testing and structural health monitoring applications to detect material defects such as delaminations, cracks, or inclusions. This work presents a sensing concept based on guided electromagnetic waves (GEW), in which the waveguide forms a union with the structure to be inspected. Exploiting ultra-wideband signals a surface defect in the area under the waveguide can be detected and accurately localized. This paper presents numerical and experimental GEW results for a straight waveguide focusing on the detection of through holes and cracks with different orientation. It was found that the numerical model qualitatively replicates the experimental S-parameter measurements for holes of different diameters. A parametric numerical study indicates that the crack parameters such as its orientation and width has a significant influence on the interaction of the incident wave with the structural defect. On top, a numerical study is performed for complex-shaped rectangular waveguides including several waveguide bends. Besides a successful damage detection, the damage position can also be precisely determined with a maximum localization error of less than 3%.

In this paper, a novel miniaturized implantable circular antenna is presented. It supports both wireless information communication and wireless energy transmission at the Medical Device Radiocommunication band (MedRadio 402–405 MHz) and the industrial, scientific, and medical bands (ISM 902.8–928 MHz). The antenna is circular to avoid sharp edges while miniaturization is achieved by adding two circular slots to the patch. The main scenario includes embedding into the muscle layer of a cylindrical three-layer model of a human arm for which several parameters are analyzed (resonance, radiation pattern, and specific absorption rate). Power transmission efficiency and interaction distance limits to ensure connections are also evaluated. Finally, the design is validated by an experimental measurement in an anechoic chamber, and some new improvements are proposed.

Early detection of breast cancer is required to increase the chances of a successful treatment. However, current breast-imaging systems such as X-Ray mammography, breast ultrasound, and magnetic resonance imaging have technological limitations so that novel solutions are needed to address this major societal problem. The current paper considers ultra-wideband (UWB) microwave radiation in the frequency band from 1 to 9 GHz. Given by the non-ionizing nature of microwaves frequent check-ups are more feasible. In this work, we propose algorithms for qualitative and quantitative microwave breast imaging for a transmission-based UWB system. Based on numerical and experimental data, the performance of the algorithms has been investigated and compared. Finally, microwave images obtained during an initial patient study are discussed relative to corresponding X-ray images.

This paper presents the integration and channel characterization of a highly integrated dual-band digital beamforming space-borne synthetic aperture radar (SAR) receiver. The proposed SAR sensor is a low-cost, lightweight, low-power consumption, and dual-band (X/Ka) dual-polarized module ready for the next-generation space-borne SAR missions. In previous works, by the authors, the design and experimental characterization of each sub-system was already presented and discussed. This work expands upon the previous characterization by providing an exhaustive experimental assessment of the fully integrated system. As it will be shown, the proposed tests were used to validate all the instrument channels in a set-up where the SAR sensor was illuminated by an external source minim the ground reflected waves. Test results demonstrate how the system channels are properly operating allowing the reception of the input signals and their processing in the digital domain. The possibility to easily implement a calibration procedure has also been validated to equalize, in the digital domain, the unavoidable amplitude differences between the different channels.

Airbus Italia recently developed enhanced passive components as key elements for its telecommunication Ku-band antenna product lines, tailored to reconfigurable payloads. This paper describes the design and qualification of a dual linear polarization Ku-band-radiating chain, developed for the DRA receive (Rx) active antennas embarked on the Eutelsat Quantum satellite. The feed chain covers the entire Ku-band frequency range allocated for fixed satellite services providing receive functionality and embedding sharp rejection features over the adjacent transmit band. The proposed design provides high radiation efficiency (>90%) and polarization purity (XPD > 33 dB), together with low RF losses and flat group-delay variation over a 13% fractional bandwidth, keeping a compact size and reduced axial length. The unit has been optimized for high reproducibility in high volume productions, typical of large DRA applications, for which stringent mass and dimensional constraints, as well as excellent amplitude and phase tracking among similar units, are key features. Details of the feed chain design and an overview of RF and environmental qualification test results are presented.

Multiple antennas and multiple radio frequency (RF) chains in both the transmitter and receiver are required in conventional radio systems employing the multiple-input multiple-output (MIMO) method. This paper presents an experimental investigation of a beam-steering time-modulated MIMO receiver with a single RF chain. Implementation of the receiver is based on a time-modulated antenna array (TMAA) and a software-defined radio. The sidebands generated inherently by the TMAA are utilized as virtual spatial channels with the beam-steering functionality. Performance of the system is investigated experimentally. The bit error rate and condition number of the channel matrix are examined for different radiation patterns in order to determine favorable configurations in a given multipath environment. Obtained results show a considerable impact of the beam-steering on the performance of MIMO transmission.

In this article, a sleeve antenna with a wide impedance bandwidth that consists of a coplanar waveguide line connected to a metallic cylinder is presented. The effect of design parameters on the impedance bandwidth is considered by some simulations. In addition to the wide impedance bandwidth, the omnidirectional pattern, high efficiency, low cost and easy fabrication process, and compact dimensions cause this antenna to be a good choice for some applications at low VHF/UHF frequency bands. Due to the flexible structure of this antenna, it is possible to cover the various frequency bands by changing the parameters of the antenna. In this work a typical model of the proposed antenna for the frequency range of 127 to 586 MHz is fabricated and compared with other previous works. An equivalent circuit model has been proposed to better understand how the antenna works. The proposed antenna has a bandwidth of about 128.7% for a voltage standing wave ratio (VSWR) of less than 3, compact size of 0.274λ × 0.047λ and higher than 90% efficiency.

An inscribed hexagonal fractal slotted patch antenna with some additional geometry and slots is proposed for the optimization in this paper. This research work is concerned with the optimization of this slotted fractal antenna with the help of the curve-fitting method in conjunction with the modified version of Lightning Attachment Procedure Optimization (MLAPO) technique. The data required for the curve-fitting technique and for the optimization technique have been obtained by varying some of the parameters of the proposed antenna. Different equations are developed to know the relations between these parameters of the proposed antenna. The MLAPO technique is applied thereafter to calculate the different optimized geometrical parameters to optimize the bandwidth for the proposed antenna. The optimized geometrical parameters are verified with the help of a parametric variation to justify the reliable optimization. The bandwidth obtained by the MLAPO technique has been found to be better than that obtained by PSO and normal LAPO algorithm. The prototype of the optimized antenna is fabricated and the experimental results are found to be compatible with the results obtained by simulation. The proposed optimized antenna may be utilized in various applications in C and X bands.

A flexible broadband antenna with high radiation efficiency for the Internet of Things (IoT) applications is presented. The design is based on a U-shaped and a triangular-shaped radiator with two tuning stubs. A 50 Ω coplanar waveguide (CPW) transmission line is employed to feed the antenna. The proposed antenna is fabricated on a flexible substrate from a composite synthesized by mixing natural rubber with SiO2 as a filler. The radiating elements, along with the CPW, are built using a highly conductive woven fabric. Results show that the antenna has a simulated and measured impedance bandwidth of 0.856–2.513 GHz and covers the most commonly used wireless communication standards and technologies for IoT applications. The radiation efficiency of the antenna reaches over 75% throughout the operating frequency band with satisfactory radiation patterns and gain. The flexible antenna was also tested under bending conditions. The presented results demonstrate that bending has a minor effect on the antenna performance within the target frequency range. The measured results show a good agreement with simulations.