The Revival of interest in flight by man's own muscle power brings back to me some early attempts to solve this problem some 30 years ago.

Needless to say I was—and still am—sold on this idea ever since reading Lilienthal's famous book as a youngster in school. Then came the Wright Brothers and the early years of flying and the years of the First Great War at the end of which I found myself as an Aerodynamicist, designing wing sections and calculating induced drag according to Prandtl's newly discovered wing theory.

The end of the war found us meditating about gliding and the possibility of soaring flight. And so came the Rhoen, and the “Sturm und Drang” of the years on the Wasserkuppe.

An experimental, remotely-piloted aircraft has been designed and fabricated at University of Michigan that is aeroelastically representative of very flexible aircraft. Known as X-HALE, this Experimental High-Altitude Long-Endurance aircraft exhibits geometrically nonlinear behaviour and displays specific aeroelastic characteristics designed into the experiment. This paper presents the data from the initial flight tests of the lightly instrumented X-HALE Risk Reduction Vehicle that confirm the expected aeroelastic characteristics. This opens the way for future flight tests with a fully-instrumented platform which will provide data to support validation of coupled, nonlinear aeroelastic/flight dynamic codes.

In 1998, Swissair Flight 111 (SR111) developed an in-flight fire shortly after take-off which resulted in the loss of the aircraft, a McDonnell Douglas MD-11, and all passengers and crew. The Transportation Safety Board (TSB) of Canada, Fire and Explosion Group launched a four year investigation into the incident in an attempt to understand the cause and subsequent mechanisms which lead to the rapid spread of the in-flight fire. As part of this investigation, the SMARTFIRE Computational Fluid Dynamics (CFD) software was used to predict the ‘possible’ development of the fire and associated smoke movement. In this paper the CFD fire simulations are presented and model predictions compared with key findings from the investigation. The model predictions are shown to be consistent with a number of the investigation findings associated with the early stages of the fire development. The analysis makes use of simulated pre-fire airflow conditions within the MD-11 cockpit and above ceiling region presented in an earlier publication (Part I) which was published in The Aeronautical Journal in January 2006.

The integral equation approach to the mixed flow problem of infinite wings at high subsonic speeds is adopted for non-circulatory and circulatory (lifting) flows. The solutions are determined from a system of non-linear algebraic equations and, to ensure always unique solutions, the method of differentiation with respect to a parameter has been applied. The resulting Cauchy problem is then solved with the linearised flow solution as the initial value vector. For the case of embedded shocks in the flow field, the method of steepest descent has been added to the calculation scheme. Results for subcritical and supercritical flows past aerofoils are given and compared with solutions obtained by finite-difference techniques.

The first object of this paper is to show the concordance between three different theoretical approaches to flame stabilisation and to compare published experimental data with the theoretical predictions. Good agreement between the theory and experimental results is obtained. The second object is to show that, at low pressures, the predictions of these theories must be qualified in view of the increasing importance of heat losses from the flame region. It is shown that there must exist a minimum pressure below which a flame cannot be maintained in a given combustible mixture, irrespective of the rate of flow of the mixture, unless heat losses are entirely eliminated.

Wind tunnel data from a tanker wing and receiver aircraft model at varying vertical separation have been compared with theoretical results. In the aerodynamic model the tanker wing is represented by a horseshoe vortex while the aerodynamic loads on the receiver are determined by the vortex lattice method and lifting-line theory, although an approximate method is used to determine the side force on the fin. In the longitudinal case data were obtained for low, mid and high tailplane positions and, with the exception of the pitching moment results, fairly good agreement is obtained between theory and experiment. The relatively small differences are due mainly to the wind tunnel boundary interference effect which could not be quantified for the pitching moment measurements. The lateral aerodynamic interference was determined by banking the tanker wing and displacing it sideways and by yawing the receiver model. Fairly good agreement is obtained between the theory and experiment for the most significant terms which are the rolling moments due to bank and sideways displacement. The effect of the sidewash due to the tanker wake on the receiver in yaw is found to be relatively insignificant. Over the range of bank, yaw and sideways displacements tested the results are almost linear.

Theoretical and experimental natural frequencies and modal shapes up to the fifth mode of vibration are given for a straight blade of asymmetrical aerofoil cross-section. The theoretical procedure consists essentially of transforming the differential equations of motion into a set of simultaneous first-order equations and solving them by a step-by-step finite difference procedure. The natural frequency values are compared with results obtained by an analytical solution and with standard solutions for certain special cases. Good agreement is shown to exist between the theoretical results for the various methods presented. The equations of motion are dependent upon the coordinates of the axis of the centre of flexure of the beam relative to the centroidal axis. The effect of variations of the centre of flexure coordinates upon the frequencies and modal shapes is shown for a limited range of coordinate values. Comparison is made between the theoretical natural frequencies and modal shapes and corresponding results obtained by experiment.

The future air traffic management (ATM) concept envisaged by the Single European Sky ATM Research – SESAR – and the USA equivalent NextGen, mark a paradigm shift from the current reactive approach of ATM towards holistic strategic collaborative decision making. The core of the future ATM concept relies on common situational awareness over potentially large time-horizons, based upon the user operational intent. This is beyond human capabilities and requires the support of automation tools to predict aircraft state throughout the operation and provide support to optimal decision making long before any potential conflict may arise. This is achieved with trajectory predictors and conflict detectors and resolvers respectively. Numerous tools have been developed, typically geared towards addressing specific airborne applications. However, a comprehensive literature search suggests that none of the tools was designed to predict trajectories throughout the entire operation of an aircraft, i.e. gate-to-gate. Yet, such functionality is relevant in the holistic optimisation of aircraft operations. To address this gap, this paper builds on an existing en route trajectory prediction (TP) model and develops novel techniques to predict aircraft trajectories for the transitions between the ground- and enroute-phases of operation and for the ground-phase, thereby enabling gate-to-gate (or enroute -to-enroute) TP. The model is developed on the basis of Newtonian physics and operational procedures. Real recorded data obtained from a flight data record (FDR) were used to estimate some of the input parameters required by the model. The remaining parameters were taken from the BADA 3.7 model. Performance results using these flight data demonstrate that the proposed TP model has the potential to accurately predict gate-to-gate trajectories and to support future ATM applications such as gate-to-gate synchronisation.

Experimental results are presented of the measurement of skin friction in fully developed turbulent flow in concentric annuli using Preston tubes situated on the inner and outer annular surfaces. Both Preston's calibration and Patel's calibration were used to evaluate the results. It was found that the latter gave excellent results. Several radius ratios were investigated with a reasonable range of the annulus Reynolds number. The good agreement was not affected by radius ratio or smallness of core tube within the range of these parameters investigated here.

Classical gas dynamics is by definition the dynamics of gases that are in local thermodynamic equilibrium everywhere in the flow field so that their thermodynamic behaviour is completely specified by two independent variables of state, for example by pressure p and density p. The fundamental assumption of local thermodynamic equilibrium is not valid in many flow situations of practical importance, and this fact has given rise to a revision and generalisation of classical gas dynamics. This generalisation is usually called “relaxation gas dynamics”. Ten years ago J. Ackeret mentioned this subject briefly at the end of the Daniel and Florence Guggenheim Memorial Lecture on The Role of Entropy in the Aerospace Sciences. He gave that lecture at the 2nd International Congress of the Aeronautical Sciences in Zürich (12th September 1960) and he said on that occcasion: “Non-equilibrium states are of growing importance, for strictly speaking, exact (thermodynamic) equilibrium occurs only relatively seldom in gas dynamics. However, a rational theory of nonequilibrium states must necessarily be extremely complicated….

A project was recently completed that investigated the ability to predict the onset of flutter using tools like the flutterometer. This project used an experiment called the aerostructures test wing that was flown while mounted to the flight test fixture on an F-15. Several flight tests were conducted to expand the envelope and determine the aeroelastic dynamics of the experiment. The final flight ended with destruction of the experiment due to the onset of flutter. The flutterometer attempted to predict this onset by analysing the flight data. The results indicate the flutterometer is able to generate a conservative estimate of the flight conditions associated with flutter. This paper details the flight tests of the experiment and the resulting predictions from the flutterometer.

Aerodynamic optimisations of a blended wing-body (BWB) aircraft are presented. A discrete adjoint solver is used to calculate efficiently the gradients, which makes it possible to optimise for a large number of design variables. The optimisations employ either a variable-fidelity method that combines low- and high-fidelity models or a direct sequential quadratic programming (SQP) method. Four Euler optimisations of a BWB aircraft are then presented. The optimisation is allowed to change a series of master sections defining the aircraft geometry as well as the sweep angle on the outer wing for two of the optimisations. Substantial improvements are obtained, not only in the Euler mode but also when the optimised geometries are evaluated using Reynolds-averaged Navier-Stokes solutions. Some interesting features of the optimised wing profiles are discussed.

An investigation into the behaviour of clustered synthetic jet Actuators for flow-control applications is described. Experiments have been undertaken with two small-scale synthetic jet actuators in a zero-pressure gradient boundary-layer, in order to investigate the effect of configuration yaw angle and relative input signal phase. Oil-flow visualisation and hotwire anemometry techniques were used, demonstrating that changes in the downstream flow structure could be observed. Compared to a streamwise configuration, in which a symmetrical counter-rotating vortex pair was produced by the synthetic jet-boundary-layer interaction, a broader asymmetric interaction was produced in a 15° yaw configuration. Streamwise velocity contour plots, illustrating the development of the interaction downstream, over four phase angles, were presented. Significant differences in the PSD analyses of downstream streamwise velocity time histories were found, suggesting that input signal phase could influence the stability and hence effectiveness of flow structures used in flow-control applications.

In a paper in the number of this journal for November, 1925, it was shown that if a flying machine were fitted with wings of standard section and these were flapped in a rhythmical manner, the machine would be supported and propelled, its weight, dimensions and velocity being those of a typical bird; the degree of accuracy attempted in the analysis did not exceed five per cent.

A subsequent examination of the power involved established a high efficiency; but this was due to a large amount of negative work during up–beats; and although such conditions might be maintained in a mechanical model they were unlikely in a bird, which has a large muscle, the pectoralis minor, for lifting its wings. In a bird efficiency seemed to require that the angle of incidence of the outer portion during an up–beat should be negative (see §7, p. 593, of the previous paper); the angle was however made zero (see §9) in order to secure adequate lift, and it is this feature which gives rise to the negative work.

Oil-jet lubrication and cooling of high-speed gears is frequently employed in aeronautical systems, such as novel high-bypass civil aero engines based on the geared turbofan technology. Using such oil-jet system, practitioners aim to achieve high cooling rates on the flanks of the highly thermally loaded gears with minimum oil usage. Thus, for an optimal design, detailed knowledge about the flow processes is desired. These involve the oil exiting the nozzle, the oil impacting on the gear teeth, the oil spreading on the flanks, the subsequent oil fling-off, as well as the effect of the design parameters on the oil flow. Better understanding of these processes will improve the nozzle design phase, e.g. regarding the nozzle positioning and orientation, as well as the nozzle sizing and operation.

Most related studies focus on the impingement depth to characterize the two-phase flow. However, the level of information of this scalar value is rather low for a complete description of the highly dynamic three-dimensional flow. Motivated by the advancements in numerical methods and the computational resources available nowadays, the investigation of the oil-jet gear interaction by means of computational fluid dynamics (CFD) has come into focus lately.

In this work, a numerical setup based on the volume-of-fluid method is presented and employed to investigate the two-phase flow phenomena occurring in the vicinity of the gear teeth. The setup consists of a single oil-jet impinging on a single rotating spur gear. By introducing new metrics for characterizing the flow phenomena, extensive use of the possibilities of modern CFD is made, allowing a detailed transient and spatially resolved flow analysis. Thus, not only the impingement depth, but also the temporal and spatial evolution of wetted areas on the gear flanks, as well as the evolution of the oil volume in contact with the gear flanks are extracted from the simulation data and compared in a CFD study.

The study consists of 21 different simulation cases, whereby the effect of varying the jet velocity, the jet inclination angle, the jet diameter, and the gear speed are examined. Consistent results compared to a simplified analytical approach for the impinging depth are obtained and the results for the newly introduced metrics are presented.

The aviation industry relies on accurate models. These models are used to predict an aircraft system’s outputs, and thus allow an understanding of the parameters involved, which could lead to system improvements. This study focuses on the engine modelling of an aircraft, and on its experimental validation using the Cessna Citation X Research Aircraft Simulator designed by CAE Inc., equipped with a level D Flight Dynamics toolbox. Level D is the highest rank attributed by the Federal Aviation Administration FAA certification authorities for flight dynamics. The proposed model aims to predict the thrust and the fuel consumption for various altitudes, Mach numbers and throttle lever angles (TLA). Different generic static models, which correspond to their steady state, from the literature, were used in this study; however, most of them were validated under restricted hypotheses. An optimisation algorithm was used in order to tune the static model parameters with the set of identification flight test data. Another set of data was then used in order to validate the identified model. Furthermore, a dynamic model corresponding to the transient operations was identified. TLA steps, impulses and ramp perturbations were performed in order to identify the system response, and to validate system dynamic model with other flight tests than the identification tests.

An integrated artificial immune system-based scheme that can operate over extended areas of the flight envelope is proposed in this paper for the detection and identification of a variety of aircraft sensor, actuator, propulsion, and structural failures/damages. A hierarchical multi-self strategy has been developed in which different self configurations are selected for detection and identification of specific abnormal conditions. Data collected using a motion-based flight simulator were used to define the self for a wide area of the flight envelope and to test and validate the scheme. The aircraft model represents a supersonic fighter, including model-following direct adaptive control laws based on non-linear dynamic inversion and artificial neural network augmentation. The proposed detection scheme achieves low false alarm rates and high detection and identification rates for all the categories of failures considered.

A ‘two dimensional’ air intake comprising a wedge followed by an isentropic compression has been tested in the Cranfield Gun Tunnel at Mach 8·2. These tests were performed to investigate qualitatively the intake flow starting process. The effects of cowl position, Reynolds number, boundary-layer trip and introduction of a small restriction in the intake duct were investigated. Schlieren pictures of the flow on the compression surface and around the intake entrance were taken. Results showed that the intake would operate over the Reynolds number range tested.

Tests with a laminar boundary layer demonstrated the principal influence of the Reynolds number on the boundary-layer growth and consequently on the flow structure in the intake entrance. In contrast boundary layer tripping produced little variation in flow pattern over the Reynolds number range tested. The cowl lip position appeared to have a strong effect on the intake performance. The only parameter which prevented the intake from starting was the introduction of a restriction in the intake duct.

The experimental data obtained were in good qualitative agreement with the CFD predictions. Finally, these experimental results indicated a good intake flow starting process over multiple changes of parameters.

Machining-induced surface integrity has an important effect on reliability and service life of the components used in the aerospace industry where titanium alloy Ti-6Al-4V is widely applied. Characterisation of machining-induced surface integrity and revealing its effect on fatigue life are conducive to structural fatigue life optimisation design. In the present study, surface topography, residual stress, microstructure and micro-hardness were first characterised in peripheral milling of titanium alloy Ti-6Al-4V. Then, low-cycle fatigue performances of machined specimens were investigated on the basis of the tension-tension tests. Finally, the effects of surface integrity factors (stress concentration factor, residual stress and micro-hardness) on fatigue performances were discussed. Results show that stress concentration can reduce the fatigue life while increasing the residual compressive stress, and micro-hardness is beneficial to prolonging the fatigue life, but when the surface material of the specimen is subjected to plastic deformation due to yield, the residual stress on the surface is relaxed, and the effect on the fatigue performance is disappeared. Under the condition of residual stress relaxation, the stress concentration factor is the main factor to determine the low-cycle fatigue life of titanium alloy Ti-6Al-4V. While for the specimens with no residual stress relaxation, micro-hardness was the key factor to affect the fatigue life, followed by residual stress and stress concentration factor, respectively.

A study of the effect of linear damping on flutter speed is described. The energy exchange at flutter is considered in each degree of freedom of a general n-degrees-of-freedom system and an energy compatibility equation is formed. An analytical discussion of binary systems, based on the energy compatibility equation, is then presented.