Microwave power measurements

doi:10.1017/CBO9781139567626.007

6 - Microwave power measurements

from Part II - Microwave instrumentation

Published online by Cambridge University Press: 05 June 2013

Edited by

Andrea Ferrero and

Ronald Ginley: Affiliation:
NIST, USA
Valeria Teppati: Affiliation:
Swiss Federal University (ETH), Zürich
Andrea Ferrero: Affiliation:
Politecnico di Torino
Mohamed Sayed: Affiliation:
Microwave and Millimeter Wave Solutions, Santa Rosa

Book contents

Get access

Summary

Introduction

In physics, power is the rate at which energy is transferred, used, or transformed. For example, the rate at which a light bulb transforms electrical energy into heat and light is measured in watts – the more wattage, the more power, or equivalently the more electrical energy is used per unit time [1]. Energy transfer can be used to do work, so power is also the rate at which this work is performed [2].

For systems or circuits that operate at microwave frequencies, the output power is usually the critical factor in the design and performance of that circuit or system. Measurement of the power (signal level) is critical in understanding everything from the basic circuit element up to the overall system performance. The large number of signal measurements that can be made and their importance to system performance means that the power-measurement equipment and techniques must be accurate, repeatable, traceable, and convenient.

In a system, each component in a signal chain must receive the proper signal level from the previous component and pass the proper signal level on to the succeeding component. If the output signal level becomes too low, the signal becomes obscured in noise. If the signal level becomes too high, though, the performance becomes nonlinear and distortion can result. The uncertainties associated with the measurement of power also play a very important role in the development and application of microwave circuits. For example, a 10 W transmitter costs more than a 5 W transmitter.

Type: Chapter
Information: Modern RF and Microwave Measurement Techniques , pp. 130 - 159

DOI: https://doi.org/10.1017/CBO9781139567626.007 [Opens in a new window]

Publisher: Cambridge University Press

Print publication year: 2013

Access options

Get access to the full version of this content by using one of the access options below. (Log in options will check for institutional or personal access. Content may require purchase if you do not have access.)

References

[1] D., Halliday and R., Resnick, Fundamentals of Physics. Wiley Illustrated, 1974, Chapter 6, Section 7.Google Scholar

[2] R. P., Feynman, R. B., Leighton, and M., Sands, The Feynman Lectures on Physics. Pearson Education, Volume I, 1963, pp. 13–23.

[3] “Fundamental of RF and Microwave Power Measurements (Part 1),” Agilent Technologies, Application Note 64-1, 5988-9213EN, April 2003.

[4] G. F., Engen, Microwave Circuit Theory and Foundations of Microwave Metrology. London, UK: Peter Peregrinus Ltd., 1992, pp. 103–128.Google Scholar

[5] M., Kinishita, “Atomic microwave power standard based on the Rabi frequency,” IEEE Trans. Instrum. and Meas., vol. 60, issue 7, July 2001, pp. 2696–2701.Google Scholar

[6] “Digital Modulation in Communications Systems – An Introduction,” Agilent Technologies, Application Note 1298, 5965–7160E, 2001.

[7] G., Breed, “Fundamentals of pulsed and time-gated measurements,” High Frequency Electronics, Nov. 2010, pp. 52–56.Google Scholar

[8] “Gated Measurements Made Easy,” News from Rohde & Schwarz, No. 185, 2005, pp. 15–17.

[9] “Fundamentals of RF and Microwave Power Measurements (Part 2),” Agilent Technologies, Application Note 64-2, 5988-9214EN, July 2006.

[10] “Using Error Vector Magnitude Measurements to Analyze and Troubleshoot Vector-Modulated Signals,” Agilent Technologies Product Note 89400-14, 2000.

[11] A., Fantom, Radio Frequency and Microwave Power Measurement. London, UK: Peter Peregrinus Ltd., 1990, chapters 2–8.Google Scholar

[12] N. T., Larsen, “A new self-balancing DC-substitution RF power meter,” IEEE Trans. Instrum. and Meas., vol. IM-25, no. 4, Dec. 1976, pp. 343–347.Google Scholar

[13] F. R., Clague and P. G., Voris, “Coaxial Reference Standard for Microwave Power,” NIST Technical Note 1357, April 1993.Google Scholar

[14] F. R., Clague, “A Calibration Service for Coaxial Reference Standards for Microwave Power,” NIST Technical Note 1374, May 1995.Google Scholar

[15] P. S., Filipski, R. F., Clark, and D. C., Paulusse, “Calibration of HF thermal voltage converters using an asymmetrical tee,” IEEE Trans. Instrum. and Meas., vol. 50, no. 2, April 2001, pp. 345–348.Google Scholar

[16] M., Halawa and N., Al-Rashid, “Performance of the single junction thermal voltage converter at 1 MHz via equivalent circuit simulation,” Cal Labs Magazine, Apr./May/Jun. 2009, pp. 40–45.Google Scholar

[17] R. J., Wylde, “Installation and Operating Instructions for the TK TeraHertz Absolute Power Meter System,” product manual, Nov. 2002.Google Scholar

[18] “Power Measurement above 110 GHz,” VDI Application Note, Oct. 2007.

[19] K. E., Bramall, “Accurate microwave high power measurements using a cascaded coupler method,” Journal of Research of the National Bureau of Standards, vol. 75c, no. 3 and 4, July–Dec. 1971, pp. 185–192.Google Scholar

[20] “Fundamental of RF and Microwave Power Measurements (Part 4),” Agilent Technologies, Application Note 64-2, 5988-9214EN, Sept. 2008.

[21] R. A., Ginley, “A direct comparison system for measuring radio frequency power (100 kHz to 18 GHz),” Proceedings of the Measurement Science Conference, 2006.Google Scholar

[22] J. R., Juroshek, “NIST 0.05–50 GHz direct comparison power calibration system,” Proceedings of the Conference on Precesion Electromagnetic Measurements, 2000, pp. 166–167.Google Scholar

[23] M. P., Weidman, “Direct comparison transfer of microwave power sensor calibrations,” NIST Technical Note 1379, Jan. 1996.Google Scholar

[24] R. W., Beatty and A. C., McPherson, “Mismatch errors in microwave power measurements,” Proceedings I.R.E., 1953, vol. 41, Sept. 1953, pp. 1112–1119.Google Scholar

[25] A. Y., Rumsfelt and L. B., Elwell, “Radio frequency power measurements,” Proc. IEEE, vol. 55, no. 6, June 1967, pp. 837–850.Google Scholar

[26] “Fundamental of RF and Microwave Power Measurements (Part 3), Agilent Technologies, Application Note 64-32, 5988-9215EN, April 2011.

[27] G. F., Engen, “A method of determining the mismatch correction in microwave power measurements,” IEEE Trans. Instrum. Meas., vol. IM-17, no. 4, Dec. 1968, pp. 392–395.Google Scholar

[28] D. M., Kerns and R. W., Beatty, Basic Theory of Waveguide Junctions and Introductory Microwave Network Analysis. London, UK: Pergamon Press, pp. 42–50.

[29] “Evaluation of Measurement data – Guide to the Expression of Uncertainty in Measurement,” BIPM – JCGGM 100:2008, 1995.

[30] B. N., Taylor and C. E., Kuyatt, “Guidelines for Evaluating and Expressing the Uncertainty of NIST Measurement Results”, NIST, Technical Note 1297, 1993.Google Scholar

[31] K., Shimaoka, M., Shida, and K., Komiyama, “Source reflection coefficient measurements of the power reference of power meters,” Proceedings of the Conference on Precision Electromagnetic Measurements, July 2006,Google Scholar

[32] J. R., Juroshek, “A direct calibration method for measuring equivalent source mismatch,” Microwave Journal, Oct. 1997, pp. 106–118.Google Scholar

[33] H., Jager, “Measurement Method for Determining the Equivalent Reflection Coefficient of Directional Couplers and Power Splitters,” Rohde & Schwarz Application Note 08.02-1EZ51_1E.

Book contents

6 - Microwave power measurements

Summary

Access options

References

Save book to Kindle

Save book to Dropbox

Save book to Google Drive