Book contents
- Frontmatter
- Dedication
- Contents
- Preface
- General introduction
- 1 Mechanism and the mobility of mechanism
- 2 Overconstraint and the nature of mechanical motion
- 3 Some of the various lines in a moving body
- 4 Enumerative geometry and the powers of infinity
- 5 Rigidity and the instantaneous screw axis
- 6 Irregularity and the freedoms within a joint
- 7 The possibilities in reality for practical joints
- 8 Some elementary aspects of two degrees of freedom
- 9 The linear complex of right lines in a moving body
- 10 Line systems and the dual vectors in mechanics
- 11 Geometrical properties of the linear line systems
- 12 The vector polygons for spatial mechanism
- 13 On the two theorems of three axes
- 14 Some reciprocities across the middle number three
- 15 The generality and the geometry of the cylindroid
- 16 The discovery in a mechanism of a cylindroid
- 17 Action, notion, clearances and backlash
- 18 Singular events in the cycles of motion
- 19 Fundamental relations and some algebraic methods
- 20 The special geometry of some overconstrained loops
- 21 The helitangent lines in a moving body
- 22 The cylindroid in gear technology
- 23 The general and the special screw systems
- Bibliography
- Index of proper names
- Subject Index
8 - Some elementary aspects of two degrees of freedom
Published online by Cambridge University Press: 07 September 2010
- Frontmatter
- Dedication
- Contents
- Preface
- General introduction
- 1 Mechanism and the mobility of mechanism
- 2 Overconstraint and the nature of mechanical motion
- 3 Some of the various lines in a moving body
- 4 Enumerative geometry and the powers of infinity
- 5 Rigidity and the instantaneous screw axis
- 6 Irregularity and the freedoms within a joint
- 7 The possibilities in reality for practical joints
- 8 Some elementary aspects of two degrees of freedom
- 9 The linear complex of right lines in a moving body
- 10 Line systems and the dual vectors in mechanics
- 11 Geometrical properties of the linear line systems
- 12 The vector polygons for spatial mechanism
- 13 On the two theorems of three axes
- 14 Some reciprocities across the middle number three
- 15 The generality and the geometry of the cylindroid
- 16 The discovery in a mechanism of a cylindroid
- 17 Action, notion, clearances and backlash
- 18 Singular events in the cycles of motion
- 19 Fundamental relations and some algebraic methods
- 20 The special geometry of some overconstrained loops
- 21 The helitangent lines in a moving body
- 22 The cylindroid in gear technology
- 23 The general and the special screw systems
- Bibliography
- Index of proper names
- Subject Index
Summary
Some bases for an argument
01. For the reader already familiar with other discussions about the cylindroid (chapters 6, 15, 16 and elsewhere) it will be clear that a cylindroid is always lurking wherever there is a situation of two degrees of freedom – or wherever there are two forces or wrenches acting (§ 10.14). For the reader unaware as yet of the relevant generalities, the present chapter may be taken as a piece of purposely confusing, preliminary reading. It must be said in the kinematics (and the statics) of mechanism that the simpler a situation appears to be, the more baffling its deeper aspects often are. The science of the relative motion of rigid contacting bodies is bedevilled by degeneracies of its general geometry; these degeneracies, when taken in isolation, have a tendency to render the science a miscellany of unrelated facts and alleged separate theorems for which there appears to be no integrative binding. This chapter deals with some of that miscellany but with almost none of its binding; I shall be dealing here with the kinematics of only a few special cases of two degrees of freedom and I offer no conclusive results at the end of it.
02. However with no more than a primitive understanding of the relationship c + f= 6, where c is the number of constraints upon a body and/is its number of freedoms (§ 1.52), we can begin a useful argument here about the matter of two degrees of freedom.
- Type
- Chapter
- Information
- Freedom in Machinery , pp. 130 - 139Publisher: Cambridge University PressPrint publication year: 2007