Adrenal gland-induced hypertension, also known as secondary hypertension, is a medical condition caused by an underlying adrenal pathology, most typically adrenocortical adenomas. Current clinical practices involve pharmacotherapy or surgical resection to treat adrenal gland diseases that cause hypertension. However, due to the limitations of these treatment options, microwave ablation (MWA) has emerged as a promising minimally invasive alternative. An accurate understanding of the dielectric properties of adrenal glands would support the further development and optimization of MWA technology for treating adrenal tumors. Only a few studies have examined the dielectric properties of both human and animal adrenal glands, and the sample sizes of these studies have been relatively small. Therefore, further dielectric data of human and animal adrenal glands are warranted. This paper presents the ex vivo dielectric properties of the ovine adrenal glands (medulla and cortex) and summarizes the published literature on dielectric data of adrenal glands from porcine, bovine, ovine, and human samples in the microwave frequency range to analyze the consistency and reliability of the reported data. The dielectric properties of the ovine adrenal glands (N = 8) were measured using an open-ended coaxial probe measurement technique at frequencies ranging from 0.5 to 8.5 GHz. This study also investigated the temperature-dependent dielectric properties of the ovine adrenal medulla ranging from 37 to 64°C at frequencies ranging from 0.5 to 8.5 GHz. The dielectric properties of the ovine adrenal medulla measured in this study were found to be consistent with the literature. Moreover, the review suggests that variations exist in the dielectric properties of the adrenal medulla and cortex among species. The study also found that the dielectric properties of the adrenal medulla decrease with increasing temperature, similar to other tissues for which temperature-dependent dielectric data have been reported. This summary of dielectric data of adrenal glands and the temperature-dependent dielectric properties of the ovine adrenal medulla will accelerate the development of MWA technologies for hypertension treatment.

In this study, a novel, cost-effective miniaturized tag antenna was developed for applications on the human body. To achieve impedance matching with the complex conjugate impedance of the Monza-4 tag chip (7.17–j74.22 Ω at 915 MHz), the proposed structure was configured by coarsely tuning the positions of vias and fine-tuning the small gaps of its coupled patches. For further reducing the profile and dimensions of the antenna, a design technique based on the three-dimensional dipole antenna current distribution was used. The proposed antenna configuration was not only miniaturized but also achieved a long stable reading distance (>5.0 m) and a wide impedance bandwidth of 71 MHz or 7.65% (covering the ultrahigh frequency radio frequency identification ranges in most regions), regardless of the location of the tag on the human body. Experiments were conducted to validate the simulated results, and adequate agreement was found between the simulated results and the measured results.

This article presents the design of a novel sigma slotted circular monopole antenna for wireless body area network applications. The design is proceeded with a sigma-shaped slot etched on the circular radiator with Rogers 4003C substrate. The size of the proposed antenna is 30 × 30 × 1 mm3. With partial ground plane, the bandwidth characteristics of the antenna have been enhanced. The designed antenna covers 2–10 GHz of the ultra wideband, thereby providing more than 106% bandwidth. The antenna exhibits high gain values of 1.95, 3.23, 3.46, and 5.95 dB at 2.45, 3.45, 5.8, and 9.5 GHz, respectively. The proposed design operates on off-body mode at 2.45 GHz and on-body mode at 5.8 GHz, thus acting as a dual-mode antenna. To ensure the health and safety measure, specific absorption rate analysis was done for both low and high values of input power and also with Cartesian and cylindrical human arm models. Bending analysis was also done. The time domain parameter group delay was also analyzed for the proposed antenna for on- and off-body scenarios. The prototype was fabricated, and validation of simulation results was done for free space and on-body scenarios.

This research work presents an implantable antenna that operates at 5.8 GHz. By using a radiator with a loop-based design, the antenna can be made smaller. Radiator is made up of three connected rectangular loops. On the substrate’s back side, an I-shaped ground plane is used. As substrate and superstrate, polydimethylsiloxane (PDMS) with dimensions of 7 mm × 5 mm × 0.3 mm is used. The conducting sections are made using copper foil that is 30 µm thick. The suggested antenna is examined by the implantable medical device using realistic human scalp phantom models and a homogenous skin box. Simulated study revealed that it operates around 5.8 GHz with a bandwidth from 5.69 to 5.92 GHz. The specific absorption rate was 0.28 and 0.26 W/kg for skin box and human scalp phantoms, respectively, at 1 mW input power across 1 g volume tissue.

In this study, tunability of the electromagnetically induced transparency (EIT)-like transmission window by low-volume dielectric loadings is presented both numerically and experimentally in S-band. The EIT-like transmission behavior is obtained by a metamaterial, composed of an electric resonator and a closed-ring resonator patterned on a dielectric substrate. The frequency tuning is obtained by two applications called horizontal sliding application (HSA) and vertical sliding application based on sliding of the low-volume loadings from the edges to geometric center (i.e., inward). For both applications, the frequency tuning has been investigated for dielectric loadings which have relative permittivity of 2.2, 3, 4.5, and 6.15. The results reveal that the proposed sliding applications are effective on tuning the transmission peak frequency. An achieved 1136 and 971 MHz absolute spectral shifts and corresponding 6.34% and 5.41% absolute sensitivities by simulations and measurements, respectively, are the best results which are obtained for HSA at 5 mm shift value. Moreover, 14.67% sensitivity is obtained in simulations for the complete dielectric loading on the resonator in response to the increase in refractive index from 1 to 1.5. It is believed that the proposed applications will contribute to the existent sensing studies.

By combining the technique of energy selective surface and frequency selective rasorber, an energy selective rasorber is proposed, which performs selective energy protection in the low communication frequency band (0.8–2 GHz) and wave-absorbing property in the high-frequency band (6–18 GHz). The design consists of two layers, of which the bottom one contains a lumped diode structure for energy selection function in the transmission band, while together with the top layer, they perform a wideband wave absorbing function. The simulated and measured results agree well with each other, and both show good absorption in 6–18 GHz and energy-selective property around 1.86 GHz. That is, when the incident power changes from −30 to 14 dBm, the reflection coefficient changes from below −22 dB to above −2 dB, while the transmission coefficient changes from above −3 dB to below −17 dB.

A low-profile wideband circularly polarized (CP) metasurface antenna is demonstrated for C-band applications. The metasurface consists of 4 × 4 square patches with Z-shaped slots. Characteristic mode analysis is used to investigate the modal behavior of the metasurface, and a pair of degenerate modes is chosen as the operating modes. The CP radiation is realized by exciting a pair of degenerate modes of the metasurface through a slot antenna, which is used as a feed structure with a 90° phase difference. The CP bandwidth is further widened by combining the resonance modes of the metasurface and slot antenna. The measured results show that the −10 dB impedance bandwidth of the antenna is 3.47–4.76 GHz, and the 3 dB axial ratio bandwidth is 3.5–4.9 GHz with a peak gain of 6.9 dBic. Moreover, the antenna exhibits well left-hand CP radiation performances with a low profile of 0.046λ0.

In this paper, the development and designing of angle-independent metamaterial microwave absorbers are presented. The unit cell consists of two concentric circle that are linked by consolidated resistors. The absorber is built on a dielectric substrate (FR4) with a thickness of 3.2 mm (λ/0.07) and a dielectric constant of 4.3. The wideband absorption is acquired in the range of 2.8 to 10.42 GHz with a wide band of 7.62 GHz with absorptivity above 90%. In the area of interest, a flat band is obtained, and to examine the current distribution and electric field in the respective region, two peaks are considered at a frequency of 3.66 and 9.54 GHz, with maximum absorptivity of 99.99% and 99.44%, respectively. The presented absorber is examined under different angles for phi and theta variation. From the phi variation, it is observed that for all the angles, absorptivity does not vary, which confirms that the absorber is acting as an angle independent. The fabricated sheet consists of an array of a unit cell, which is examined inside the anechoic chamber with the help of two horn antennas and vector network analyzer. The tested and simulated results are compared, and it was observed that they are close in their agreement. At the end of the manuscript, the presented and already reported arts are compared, and it is observed that the presented one operates for the low frequency with higher bandwidth. The presented absorber can be practically used for defense applications for Radar Cross Sections reduction.

In this paper, a single-layer band-stop frequency selective surface (FSS) by combination of Mike Kastle unit and square ring unit is proposed to achieve wide angular stable shielding. Owing to the rotational symmetry of the structure, the designed FSS is insensitive to polarization. By the combination design, the wide angular stability can be achieved as the incident angle increases from 0° to 85°, with only a maximum frequency deviation of 0.012 GHz. Meanwhile, the mechanism of the proposed FSS is investigated by the parametric analysis of equivalent circuit model. The prototype was manufactured and measured to verify the design and simulation analysis, and the measurement results were in good agreement with the simulation results.

A novel wideband nonuniform metasurface antenna with stable gain is demonstrated. The nonuniform metasurface is composed of square patches and rings and is excited by a slot antenna. Based on characteristic mode analysis, two characteristic modes with same current direction are selected to achieve stable radiation performance in a wide frequency range. The wideband operation is achieved by assembling the resonant modes of the metasurface and slot antenna. The measured results show that the −10 dB impedance bandwidth of the proposed antenna is from 4.3 to 8.4 GHz (64.57%), and the 2 dB gain bandwidth is from 4.3 to 6.2 GHz (36.2%) with a peak gain value of 9.42 dBi. Moreover, broadside radiation performance is achieved.

In this paper, a compact unidirectional antenna consisting of a planar electric dipole and a shortened connecting element is introduced. This antenna is excited by a Γ-shaped feeding line. A wide impedance bandwidth in the frequency range of 1.3–3.3 GHz is observed in the output performance. Sufficient main lobe and low level back lobe have been introduced as other characteristics of the structure, based on radiation patterns. The antenna design process is evaluated step-by-step and using parametric study based on the antenna geometry. One of the main features of the desired antenna is the realization of circular polarization in a high percentage of the operational bandwidth 1.5–3.3 GHz. The radiation patterns of the orthogonal planes E-field and H-field along with the left-handed and right-handed circular polarization patterns for the desired antenna have been extracted and analyzed. A three-dimensional structure in the form of stacked stepped disks (SSD) is introduced to increase overall performance of antenna. There is an acceptable similarity between the E-field and H-field page patterns, which shows the accuracy of the design process. On the other hand, for studying the circular polarization, left-handed and right-handed patterns based on the main beam direction and orthogonal polarization level have acceptable performance. The maximum overall gain of the antenna in the designed frequency band is near to 13 dB.

The advancement in wireless communication is fueling the growth of innovative antenna array designs toward cost-effective and performance-oriented solutions. This paper proposed unconventional methods to design antenna arrays for multi-pattern synthesis without using attenuators or phase shifters. A low-cost alternative is proposed with “Time-modulation”-based antenna array capable of electronic scanning and beam steering. Here, “Time” is utilized as a fourth-dimensional (4D) array parameter, and that is why “Time-modulated” arrays are also called as 4D antenna arrays. The idea is to control the high-speed switch attached with each antenna periodically to produce desirable current and phase tapering. This article expanded the “Time-modulation” concept to synthesize multiple radiation patterns like monopulse patterns, scanned beam patterns, shaped beam patterns, and cosecant-squared beam patterns for multifunctional radar systems. Suitable time schemes are developed to generate the narrowband sum–difference patterns useful for monopulse radars. Simultaneous scanned beam patterns are also proposed for narrowband communication. Furthermore, to address the wideband applications, shaped flat-top beam patterns and cosecant-squared beam patterns are also proposed. In this regard, 20- and 16-element “Time-modulated” linear array antennas are developed, and the parameters of the arrays are controlled by suitably designed objective functions with quasi-Newton method (QNM)-based memetic optimization method. For this purpose, first a well-known genetic algorithm is adopted to search the potential trust regions in the exploration stage and QNM is used for fine-tuning. Furthermore, the Broyden’s good method-based direction-updating equation is used with QNM to improve the performance.

In this paper, a compact two-element reconfigurable multiple-input multiple-output (MIMO) antenna for 5G new radio sub-6 GHz is presented and discussed. The proposed MIMO antenna has four frequency operating modes: a wideband operating mode (2.41–6 GHz), a wideband operating mode with a notching band at 3.5 GHz (3.2–3.66 GHz), a low-pass filter mode that filters the higher frequencies with a wide operating band from 2.41 GHz to 4.7 GHz, and a dual-band mode with two operating narrow bands (2.41–3.16 GHz and 3.64–4.7 GHz). To improve the isolation over the entire operating band, a strip line connecting the two ground planes of the two antenna elements has been used. To validate the proposed approach, different prototypes have been fabricated and measured. The simulation results are in good agreement with the measurement results. The proposed antenna has good MIMO diversity performance with a maximum gain of 4.64 dBi. The minimum isolation is 18 dB for the four operating modes, while a measured envelope correlation coefficient of less than 0.008 is achieved. The diversity gain is near 10 dB for various operating modes. The antenna is suitable for cognitive radio and 5G sub-6 GHz applications.

A metasurface reflector-backed wideband planar antenna is designed for millimeter-wave (mmWave) applications. A simple meandering structure is used for radiation element design, while the back side consists of a partial ground plane and parasitic elements. The utilization of meander-shaped element led to small antenna dimensions. The partial ground plane is used to achieve wide bandwidth, while the parasitic elements are used to improve the impedance matching toward higher frequency bands. To achieve high gain and directional radiation characteristics, an array of metasurfaces is placed behind the radiating element. It is observed from the simulated results that the proposed antenna system offers 17.72 GHz of impedance bandwidth in the operating range of 22.28–40 GHz, while the measured impedance bandwidth is noted to be 15.8 GHz, ranging from 23 to 38.8 GHz. Furthermore, it is observed that a metasurface-based planar antenna tends to achieve a peak gain of ≈9 dBi in the band of interest.

The increasing demand for wireless communication has emphasized the need for multiband antennas. This study presents a novel design for a multiband antenna with reduced specific absorption rate (SAR), high gain, and improved front-to-back ratio (FBR) achieved through the integration with a 4 × 4 artificial magnetic conductor (AMC) surface. The proposed antenna covers a wide range of wireless frequency bands, including Industrial, Scientific, and Medical, Wireless Local Area Network, Worldwide Interoperability for Microwave Access, Wi-Fi 6E, and 7, with resonating frequencies at 2.4, 3.2, 5.5, 7.5, and 10 GHz. The AMC unit cell creates four zero-degree reflection phases with double negative properties at 2.5, 3.8, 5.5, and 7.5 GHz. The compact design measures 0.23λ0 × 0.296λ0 × 0.0128λ0 and placed 0.104λ0 above an AMC surface of size 0.512λ0 × 0.512λ0 × 0.1296λ0. This structure enhances the gain by up to 8.55dBi at 6.01 GHz. The proposed antenna has −10 dB impedance bandwidth for these corresponding frequencies viz 2.34–2.43 GHz (3.77%), 2.81–3.83 GHz (30.72%), 4.82–6.21 GHz (25.20%), 7–7.65 GHz (8.87%), and 8.06–10.31 GHz (24.5%). An overall average percentage reduction value of SAR taken at these frequencies has been found to be 96.11% with AMC structure. The antenna sample was successfully fabricated, and the experimental results have been found to match well with the simulation results. This integrated design offers a promising solution for wearable off-body communication devices.

The presence of obstacles in the propagation path is a critical factor in air-to-ground (AG) communication. The behavior of wireless signal propagation depends on several variables, such as frequency, building height, elevation angle, and street design. This paper aims to compare the three established line of sight (LOS) probability model based on actual site data, including the building geometry in suburban environment. The comparison between these three models using the site data provide a guideline for selecting the LOS probability model based on the optimistic and pessimistic predictions. The shadowing loss was evaluated at frequencies 2 and 3.5 GHz with an elevation angle of 20° in two suburban locations at Universiti Tun Hussein Onn Malaysia. Three prediction models, ITU-R P.1410-5, Holis and Pechac, and Pang et al., available in the literature were used to identify and compare the line-of-sight probability. By focusing on the shadowing model in suburban area, the guideline for optimizing LOS communications or navigation in these challenging environments can be developed. The finding highlights the importance of considering building height in AG communication for network performance evaluation and design.

In this article, the cylindrical conformation of a linearly polarized cavity-backed magnetoelectric (ME) antenna is studied. Starting from a planar ME antenna presenting a wide bandwidth due to a specific design of its feeding probe, the impact of conformation is shown; the coupling between the ME dipole and the cavity walls is demonstrated to be the key element to keep a wideband behavior. Conformal antennas offering the same impedance bandwidth as the planar antenna are presented operating at Global Navigation Satellite System frequencies (1.164–1.61 GHz). As a result of the conformation, the antenna size has to be reduced to maintain the coupling and a wideband behavior. A prototype conformed to a 44-mm radius cylinder was built using low-cost additive manufacturing. External dimensions of 62 × 62 × 35 mm3 (0.285 × 0.285 × 0.16λ03, where λ0 is the wavelength at 1.38 GHz) were obtained, showing a ground plane area reduction of 46% compared to the planar antenna with the same materials. The conformal antenna also exhibits very steady radiation properties with a gain of around 4.5 dBi and a very similar and stable 3 dB beamwidth around 113° in E- and H-planes. A relatively good agreement is found between measurements and simulation.