Each year greenhouse gas emissions remain high the climate mitigation and adaptation challenges grow. The economic downturn was already in train in 2008, yet concentrations of CO2 increased unabated. Without concerted effort across all sectors there will be little chance of avoiding ‘dangerous climate change’ and the aviation sector has a clear role to play. Current and forthcoming technologies, operational practices and behavioural change offer widespread opportunities for other sectors to mitigate their CO2 emissions in absolute terms, but as they do so, aviation will become an increasingly important player. By comparing a range of global cross-sector emission scenarios with existing aviation projections, this paper illustrates the importance of understanding the future context with regard to other sectors when assessing the aviation industry’s potential impact. Given growth projections for aviation and the relatively slow pace of technological change, aviation’s proportion of 2050 global CO2 emissions is low only in those global cross-sector emission scenarios where there is a high probability of ‘dangerous climate change’. For a ‘reasonable’ (>50%) chance of avoiding ‘dangerous climate change’, the most technologically radical scenarios for aviation make up 15% of global CO2 in 2050 and conventional scenarios exceed the carbon budget entirely. Only by recognising that aviation’s currently projected emissions are incompatible with avoiding ‘dangerous climate change’ can the industry fully grasp the challenge of accelerating innovation and managing demand to deliver a more sustainable route to 2050 and beyond.

A NACA 641-412 aerofoil with circle and star damage and also three repair configurations has been numerically investigated. Two different methods of mesh generation were employed: multi structured mesh for the star damaged aerofoil and unstructured mesh for the other aerofoils. The results show that the damage will cause a reduction in lift coefficient of the aerofoil and also a different stall angle relative to that of the undamaged aerofoil. Each kind of repair improves the aerodynamic characteristics of the aerofoil considerably. The flow Field inside the damage hole and the cavity caused by the repair sheets was also investigated. Finally, the numerical solution was qualitatively and quantitatively validated using the available experimental results.

Aspects of the turbulent wind environment Micro Air Vehicles (MAVs) experience when flying outdoors were replicated in a large wind tunnel. An overview of the facility, instrumentation and initial flight tests is given. Piloting inputs and aircraft accelerations were recorded on fixed and rotary wing MAVs and for some tests, measurements of the approach flow (u,v,w sampled at 1,250Hz at four laterally disposed upstream locations) were made. The piloting aim was to hold straight and level flight in the 12m wide × 4m high × ~50m long test section, while flying in a range of turbulent conditions. The Cooper-Harper rating system showed that a rotary craft was less sensitive to the effects of turbulence compared to the fixed wing craft and that while the fixed wing aircraft was relatively easy to fly in smooth air, it became extremely difficult to fly under high turbulence conditions. The rotary craft, while more difficult to fly per. se., did not become significantly harder to fly in relatively high turbulence levels. However the rotary craft had a higher mass and MOI than the fixed wing craft and further work is planned to understand the effects of these differences.

A series of tests were carried out to study the unsteady wake behaviour behind an aerofoil which is a section of a wind-turbine blade. The model is oscillated in pitch about its quarter chord axis at various reduced frequencies, amplitudes, and mean angles-of-attack. Instantaneous and mean velocity profiles were obtained using total and static pressure at 35 vertically aligned points behind the aerofoil via two similar rakes. The rakes were located at a distance of 1·5 chord length behind the model. An estimation of the real time and average variations of the linear momentum deficit during the oscillation cycle is obtained and has been compared with the corresponding static data. The results show that oscillation amplitude and reduced frequency have pronounced effects on the wake characteristics.

Minimisation of airframe mass reduces the costs of materials and manufacturing, as well as fuel consumption and atmospheric emissions. Fast, reliable analysis tools are required during preliminary design, when many alternative configurations and load cases are considered. The modelling and computational costs of finite element analysis are avoided by employing exact strip solutions of the governing differential equations, using the Wittrick-Williams algorithm to solve the resulting transcendental eigenproblems of buckling and vibration. This paper reviews recent enhancements to the exact strip method for analysis and optimum design of aerospace structures, using the specialist software VICONOPT. Lighter composite panels can be designed by obtaining reliable estimates of the reduced postbuckling stiffnesses when loaded in compression and shear. Further advances include discrete optimisation of layer thicknesses to allow for practical composite manufacturing constraints, vibration constraints, and a newly extended multi-level interface combining finite element analysis of a whole wing with exact strip postbuckling design of individual panels.

A lightweight robust airframe design is one of the key technological advancements necessary for the successful launch of a blended wing body aircraft. The non-circular pressure cabin dictates that substantial improvements beyond current state-of-the-art aluminium and composite structures is needed, and that improvements of this magnitude will require radically new airframe design and manufacturing practices. Such an approach is described in this paper. It is a highly integrated structural concept that is tailored and optimised to fully exploit the orthotropic nature and unique processing advantages inherent in dry carbon fibres, while also employing stitching to enable a unique damage-arrest design approach.