Introduction
Penguins evolved from an ancestral species in the subantarctic regions of Australia-New Zealand and the Antarctic Peninsula (Bertelli and Giannini Reference Bertelli and Giannini2005, Baker et al. Reference Baker, Pereira, Haddrath and Edge2006) and developed efficient morphological and physiological adaptations appropriate for the critically cold land and water temperatures of these areas (Bertelli and Giannini Reference Bertelli and Giannini2005, Dawson and Whittow Reference Dawson, Whittow and Whittow2000). While the adaptations for cold conditions of these low latitude Spheniscus penguins remain suited to the waters of cold upwelling currents, they are disadvantageous for hot terrestrial habitats where high temperatures can affect their survival and reproductive success (Luna-Jorquera Reference Luna-Jorquera1996). Penguins are generally sensitive to heat stress and during extremely high temperatures breeding adults will leave their nests unattended to cool down in the sea (Frost et al. Reference Frost, Siegfried and Burger1976, Seddon and Davis Reference Seddon and Davis1989). This tactic can be fatal for the broods of surface nesters, which are exposed not only to overheating, but also to predators that can remove a substantial proportion of a penguin colony’s chick production (Yorio and Boesrma Reference Yorio and Boersma1994, Pichegru Reference Pichegru2013). As an adaptation to hot climates, Spheniscus penguins breed in burrows dug in guano, which maintain a constant microclimate, with high relative humidity, buffered temperatures and little exposure to the wind (Frost et al. Reference Frost, Siegfried and Burger1976, Luna-Jorquera Reference Luna-Jorquera1996). Such natural burrows also provide shelter from heavy rain, which increases mortality rates of small chicks raised in surface nests (Randall et al. Reference Randall, Randall and Erasmus1986, Frere et al. Reference Frere, Gandini and Boersma1992, Renner and Davis Reference Renner and Davis2001).
In southern Africa, past guano exploitation reduced suitable burrowing habitat for the African Penguin Spheniscus demersus. Guano harvesting occurred for over more than 150 years, and removed up to 20 m of guano from some islands (Urquhart and Klages Reference Urquhart and Klages1996). Consequent reduced breeding success in penguins due to limited habitat availability caused by guano removal contributed to the 90% decrease observed in African Penguin population size during the 20th century (Frost et al. Reference Frost, Siegfried and Burger1976, Crawford et al. Reference Crawford, Williams, Hofmeyer, Klages, Randall, Cooper, Dyer and Chesselet1995). African Penguins are now ‘Endangered’ (IUCN 2012) and their population continues to decline due to a number of anthropogenic factors (Kemper Reference Kemper2006, Crawford et al. Reference Crawford, Altwegg, Barham, Barham, Durant, Dyer, Makhado, Pichegru, Ryan, Underhill, Upfold, Visagie, Waller and Whittington2011). This situation has stimulated management institutions to identify the major threats weighing on the species and set objectives to address them (Shaw et al. Reference Shaw, Waller, Crawford and Oosthuizen2012). The lack of suitable nesting habitat, leading to increased brood mortality during extreme weather events, has been identified as a major problem to be addressed (Shaw et al. Reference Shaw, Waller, Crawford and Oosthuizen2012). Global climate change is also likely to increase the frequency of extreme weather events such as heat waves or storms (Parmesan et al. Reference Parmesan, Root and Willig2000).
Conservation efforts have included the provision of artificial nests constructed of materials such as cement, fibreglass plastic and wood at several breeding sites to shelter surface-nesting penguins from extreme weather events and aerial predators (Kemper et al. Reference Kemper, Underhill, Roux and Kirkman2007, Sherley et al. Reference Sherley, Barham, Barham, Leshoro and Underhill2012, Pichegru Reference Pichegru2013). The provision of artificial nests has proved a highly successful conservation intervention in other threatened bird populations (e.g. Catry et al. Reference Catry, Alcazar, Franco and Sutherland2009, Libois et al. Reference Libois, Gimenez, Oro, Minguez, Pradel and Sanz-Aguilar2012). Among penguins, artificial nests have proved successful in increasing breeding success of Little Penguins Eudyptes minor in New Zealand by decreasing predation (Perriman and Steen Reference Perriman and Steen2000) and potentially providing protection from rain (Renner and Davis Reference Renner and Davis2001). However, similar nests deployed in Western Australia had high interior temperatures and actually failed to benefit the same species (Ropert-Coudert et al. Reference Ropert-Coudert, Cannell and Kato2004). For African Penguins, research has shown that fledging success was better in two types of artificial nests (fibreglass and cement) compared to surface nests, but hatching success was consistently lower in artificial fibreglass nests (Pichegru Reference Pichegru2013). Further studies in Namibia and South Africa have also shown that some artificial nests can improve breeding success relative to surface nests (Kemper et al. Reference Kemper, Underhill, Roux and Kirkman2007, Sherley et al. Reference Sherley, Barham, Barham, Leshoro and Underhill2012). The causes for this varying success of different artificial nest types remain largely unexplored, although temperatures are known to affect the benefits from artificial nests for other bird species (Ardia et al. Reference Ardia, Perez and Clotfelter2006, Garcia-Navas et al. Reference Garcia-Navas, Arroyo, Sanz and Diaz2008, Charter et al. Reference Charter, Meyrom, Leshem, Aviel, Izhaki and Motro2010, Catry et al. Reference Catry, Franco and Sutherland2011).
This project aimed to investigate the climatic conditions within different types of artificial nests for African Penguins and compare them to natural burrows and surface nests alongside estimates of hatching and fledging success in some of these nest types. Such information is useful to gauge the effectiveness of artificial nests in increasing penguin productivity and in turn contribute to their optimal design with the ultimate goal of maximising conservation efforts for this endangered species.
Methods
The study took place during the austral summer month of March 2012 on Bird Island, Algoa Bay, Eastern Cape, South Africa (33°50’S, 26°17’E). Algoa Bay supports almost half of all African Penguins (Crawford et al. Reference Crawford, Altwegg, Barham, Barham, Durant, Dyer, Makhado, Pichegru, Ryan, Underhill, Upfold, Visagie, Waller and Whittington2011) in an extended breeding season that lasts from January to August (Hockey et al. Reference Hockey, Dean and Ryan2005). Bird Island is grassy and flat without rocks or bushes, and although some natural burrows in guano are present, these represent only c.1% of the breeding population and most penguins (> 90%) breed in surface nests.
Two types of artificial nests were installed by South African National Parks on Bird Island in 2009 and 2010 (see Pichegru Reference Pichegru2013 for details): (1) fibreglass nests, are translucent, 60 cm long, 40 cm wide and 30 cm high, with an opening at one end 25 cm wide and 28 cm high, and some holes to allow ventilation, they were half buried in the ground and covered with large stones for shade; (2) nests made from sections of 2 cm-thick cement half pipes c.70 cm long, 30 cm wide and 30 cm high. Due to the topography of the island, all artificial nests had similar exposure to the sun. In this study we used iButtons (Thermochron iButton model DS1921L-F51, Maxim/Dallas Semiconductor Corp.) to record climatic conditions in the two types of artificial nests, as well as in natural burrows and surface nests for comparison. A total of 37 iButtons were deployed between 6 and 22 March 2012 and data were collected from 32 of them: 12 in fibreglass nests, 11 in cement nests, six in natural burrows and three in different unshaded locations on the island recording conditions experienced in the surrounding surface nests. Date losses were due either to material that got lost and failure to record. All iButtons recorded temperature every 10 minutes, while humidity was recorded at the same frequency in five fibreglass nests, six cement nests and three natural burrows. For cement nests, one iButton per nest was attached to the inside of the cement pipe using a wooden clamp (Figure 1A-1B), placed so that it would not be in contact with either the nesting bird or the cement. In fibreglass nests, the iButton was inserted through a ventilation hole so that it extended into the nest (Figure 1C). A wire was used to secure the iButton in the natural burrows, and positioned away from the breeding bird for faithful recording of nest rather than bird conditions (Figure 1D). Checks were conducted every other day during the iButton deployment, to ensure the loggers remained securely attached and were not in contact with a nesting penguin if present. In fibreglass nests, the degree of vegetation cover by grass Tetragonia spp. was recorded and ranked as 0 indicating no cover, 0.5 indicating partial cover and 1 indicating full cover. Nests were assessed for occupancy at the start and end of the deployment period and scored as either occupied (breeding birds present at the start and end of the deployment), partially occupied (breeding birds present at the start or end of the deployment) or unoccupied (no breeding birds present at either the start or end of the deployment). All breeding birds observed were incubating eggs (56%) or brooding small chicks (44%) during the period of iButton deployment.
Figure 1. (A) Close up view of iButton attached in a metal clamp and securely glued to the underside of an artificial cement nest to measure interior temperature and humidity. (B) Front view of cement nest, with iButton attached to top (circled) and nesting Spheniscus demersus underneath. (C) Wood and metal clamp device (circled) holding iButton balanced on top of an artificial fibreglass nest partially covered by vegetation. (D) iButton (circled) held by wire and pierced into the upper right side of S. demersus natural burrow.
Data from the iButtons were downloaded to a laptop computer and analysed using Microsoft Excel and Minitab. For each nest and for each day of the deployment period, we extracted the maximum temperature, the daily temperature amplitude (i.e. the range between minimum and maximum temperature recorded), and the time of day at which the maximum temperature occurred. We also calculated the amount of time for which temperatures exceeded 30°C per day. This threshold was selected as it is the temperature at which the closely related Humboldt Penguin S. humboldti become heat stressed (Drent and Stonehouse Reference Drent and Stonehouse1971). For nests where humidity was recorded we calculated minimum humidity, daily humidity amplitude and the time at which the minimum humidity occurred. Preliminary analysis indicated no influence of nest occupancy on any of the temperature or humidity parameters. This was the same whether occupancy was scored conservatively (partially occupied nests classified as ‘unoccupied’), liberally (partially occupied nests classified as occupied) or with all three occupancy states incorporated. Thus we did not consider the role of occupancy further in this study. All of these quantities were analysed using General Linear Models which included nest ID nested into nest type, with date and nest type as fixed factors. We were primarily interested in the effect of nest type while inclusion of the other factors accounted for a large proportion of the variability in the data. Tukey post-hoc tests were used to further investigate differences between each nest type. A similar approach was used to test for the effect of cover type in fibreglass nests. In all statistical testing α = 0.05. Data are presented as the Estimated Marginal Mean ± SEM from the GLMs.
In parallel, a random sample of 40–150 nests of each type (surface, fibreglass and concrete) were individually marked and their contents (number of adults, eggs, chicks and their size) were monitored weekly to bi-weekly from January to August since 2009 until failure of the breeding attempt or fledging of the chicks (see details in Pichegru Reference Pichegru2013). Natural burrows were not monitored due to the low number of these nests on the island and the sensitivity of the habitat (i.e. risk of collapse of the burrow during nest check). Each breeding attempt in a marked nest was considered independently, as most of the birds were not individually marked and more than one pair may occupy a nest site in a given season. Breeding success was estimated using Mayfield’s method (1975) and nest survival probabilities were compared using survival models with the “survreg” function in R v2.12.0 (R Development Core Team 2010), which treats the number of days to nest failure as the response variable (details in Sherley et al. Reference Sherley, Barham, Barham, Leshoro and Underhill2012, Pichegru Reference Pichegru2013). Hatching and fledging success were modelled separately with year and nest type as explanatory variables. Interactions between years and nest types were tested, but not being significant, they were removed from the models.
Results
Temperatures in all types of nests increased steadily during the morning to a maximum in the middle of the day before declining steadily again in the afternoon (Fig 2A). Maximum temperature occurred at approximately midday in surface and cement nests and significantly later at approximately 13h00 in natural and fibreglass nests (F(3, 496) = 4.3, P < 0.001). Mean daily maximum temperature in exposed nests at the colony surface was 30.7 ± 0.3 °C, but extreme temperatures in excess of 40°C were recorded in exposed (one of three), cement (two of 11) and fibreglass (seven of 12) nests, but not in natural burrows. The difference in mean maximum temperature between natural burrows and fibreglass nests was nearly 6°C (Figure 3A). Mean daily maximum temperature was significantly lower in natural burrows than exposed and both types of artificial nest (F(3, 496) = 19.4, P < 0.001). Penguins breeding in surface nests and both types of artificial nest were exposed to mean daily temperature amplitude of 12–13°C (Fig 3B). Daily temperature amplitude was significantly lower in natural burrows (F(3, 496) = 26.5, P < 0.001) at around 6°C (Figure 3B). Finally, while natural burrows rarely exceeded 30°C (on average < 10 min per day), the amount of time with temperatures above 30°C was 7.6 x greater in exposed nests, 12.1 x greater in cement nests and 16.3 x greater in fibreglass nests (F(3, 496) = 12.1, P < 0.001; Figure 3C).
Figure 2. Mean (A) temperature and (B) humidity recorded throughout the day in African Penguin nests on Bird Island, Algoa Bay, South Africa over a 17-day period in March 2012. Recordings were made in natural burrows (solid black lines), exposed surface nests (dashed black lines), cement artificial nests (solid grey lines) and fiberglass artificial nests (dashed grey lines). See text for sample sizes.
Figure 3. Mean daily (A) maximum temperature, (B) temperature amplitude and (C) the time that temperature exceeded 30°C in different types of African Penguin nests on Bird Island, Algoa Bay, South Africa over a 17-day period in March 2012. Columns with the same number above them were not significantly different from each other. See text for sample sizes and test details.
Relative humidity reached a minimum at the same time that temperatures were maximum in each nest type, which was around midday in cement nests, and slightly later around 13h30 in natural burrows and fibreglass nests, though this difference was not statistically significant (F(2, 208) = 2.5, P = 0.12; Figure 2B). Mean daily humidity amplitude was significantly greater in both types of artificial nest than in natural burrows (F(2, 208) = 19.9, P < 0.001; Figure 4A) with a range of over 40% in cement nests and less than 20% in natural burrows. Minimum relative humidity was also significantly lower in both types of artificial nest than in natural burrows (F(2, 208) = 26.0, P < 0.001; Figure 4B).
Figure 4. Mean daily (A) humidity amplitude and (B) minimum humidity in different types of African Penguin nests on Bird Island, Algoa Bay, South Africa over a 17-day period in March 2012. Columns with the same number above them were not significantly different from each other. See text for sample sizes and test details.
Vegetation cover on fibreglass nests had no effect on mean daily maximum temperature, daily temperature amplitude or the mean daily amount of time greater than 30°C (F(2, 176) = 0.39, 0.27, 0.19; P = 0.69, 0.77, 0.83; Figure 5).
Figure 5. Mean daily (A) maximum temperature, (B) temperature amplitude and (c) time that temperature exceeded 30°C in fibreglass artificial African Penguin nests with different levels of vegetation cover on Bird Island, Algoa Bay, South Africa over a 17-day period in March 2012. Columns with the same number above them were not significantly different from each other. See text for sample sizes and test details.
Confirming trends observed in Pichegru (Reference Pichegru2013), hatching success remained consistently lower in fibreglass burrows than in surface nests (Z(5, 1122) = 5.57, P < 0.0001) and concrete burrows (Z(5, 1122) = 3.38, P < 0.001, Table 1, 2). In contrast, fledging success was lowest in surface nests (Z(5, 402) = -2.71, Z = 0.007) and slightly higher in concrete than in fibreglass burrows (Z(5,402) = 2.13, P = 0.03). Fledging success generally showed greater variability between years than hatching success (Table 1).
Table 1. Hatching, fledging and breeding success from natural surface nests and two types of artificial burrows (fibreglass and cement pipes) on Bird Island, Algoa Bay, South Africa, between January-August 2009–2012 (updated from Pichegru Reference Pichegru2013).
Table 2. Results of survival analyses comparing hatching and fledging success between years (2009–2012) and nest types (surface nests, fibreglass and concrete burrows) (updated from Pichegru Reference Pichegru2013).
Discussion
The alarming declining trend of the African Penguin population in South Africa has galvanised management bodies to seek adequate solutions for every identified threat to the species, including the lack of suitable nesting habitat and predation by gulls (Shaw et al. Reference Shaw, Waller, Crawford and Oosthuizen2012). Different types of artificial nests have been installed at several breeding sites, but recent studies have demonstrated contrasting success between nest types and localities (Kemper et al. Reference Kemper, Underhill, Roux and Kirkman2007, Sherley et al. Reference Sherley, Barham, Barham, Leshoro and Underhill2012, Pichegru Reference Pichegru2013). Nevertheless, little work has been done to understand the mechanisms underpinning these observations and how these might vary between different types of artificial nests. In this study, investigating climatic conditions alongside reproductive success within artificial and natural nests revealed that current types of artificial nests are actually far from mimicking natural conditions on Bird Island. Natural burrows provide a seemingly ideal environment for breeding success, as it is insulated from extremes of temperature and with high humidity (Figs. 3 and 4). Although success in these nests could not be assessed in this study due to logistical and conservation concerns, previous studies demonstrated higher success of guano burrows over other nest types (e.g. Frere et al. Reference Frere, Gandini and Boersma1992). The guano of these natural burrows absorbs and retains moisture that is collected through precipitation and other processes, resulting in the higher moisture content in the nest interior (Frost et al. Reference Frost, Siegfried and Burger1976). Temperatures inside artificial nests were consistently higher than in natural burrows and remained high for a longer period of time, especially in fibreglass nests. Our study was conducted during incubation and early chick rearing when one adult bird must be present at all times to incubate the egg or brood the chick. At temperatures between 31 and 34°C, adult Humboldt penguins increased their Field Metabolic Rate (FMR) by 20–40% due to active thermoregulation (Luna-Jorquera Reference Luna-Jorquera1996). If we assume that African Penguins also start actively thermoregulating at temperatures above 30°C (Drent and Stonehouse Reference Drent and Stonehouse1971), individuals in artificial burrows would have to sustain higher rates of energy expenditure, for periods 12–16 times longer during a day than individuals breeding in natural burrows. Such increased energy expenditure may affect brood survival and the propensity to desert the nest, though further observational studies are required to confirm this.
Our study coincided with the end of the incubation phase for this population and extremely high temperatures may be lethal for embryos. Normal egg temperatures for African Penguins range between 31.9 and 36.0°C, with a maximum recorded being 38.7°C (Burger and Williams Reference Burger and Williams1979). Temperatures > 40°C were recorded at times in surface nests and both types of artificial burrows, especially in fibreglass nests. In the absence of ventilation in fibreglass burrows, such high temperatures combined with low humidity levels could have led to excessive and damaging water-loss by the eggs (Yom-Tov et al. Reference Yom-Tov, Wilson and Amos1986) and affected egg survival, which may explained the consistently lower hatching success in these nests (Table 1).
Penguins breeding in surface and artificial nests also experienced daily amplitudes in temperature which were double that of natural burrows (Figure 3). Magellanic Penguin S. magellanicus embryos seem to be able tolerate high variations in temperature without visible impact on their survival (Barrionuevo and Frere Reference Barrionuevo and Frere2012), although in their case temperatures varied between 20 and 34°C, which was lower than the present study. Slight variations in temperatures at incubation are known to affect growth and stress levels in ducklings (Durant et al. Reference Durant, Hepp, Moore and Hopkins2010), and it might be of interest to assess the effect of nest types on chick growth in African Penguins.
Nevertheless, of the two artificial nest types cement pipes presented the best design so far as heat-stress inducing temperatures were not retained for as long. Importantly, hatching success was higher in the cement as opposed to fibreglass nests (Table 1), suggesting that the cement nests provide not only a shelter from predators and/or direct irradiation when compared to surface nests, but also a favourable thermal environment when compared to fibreglass nests. That penguins can withstand the high temperatures and low humidity in cement nests could be explained by better ventilation, as cement nests have large openings at both ends of the pipe while fibreglass nests have only one opening supplemented by smaller ventilation holes. Our iButtons did not measure effective temperature, which takes into account the combined effects of convective and radiant heat transfer (Bakken Reference Bakken1992), but the greater ventilation and lower humidity in cement nests could facilitate heat loss by the nesting penguins, and result in a lower effective temperature. Further studies assessing the effective temperature, including radiation and particularly ventilation are necessary to understand the mechanisms underpinning the better hatching success of these nests, despite high temperatures.
Nevertheless, cement pipes showed consistent higher fledging success than other nest types, which led to significantly increased penguin productivity. This result highlights the importance of artificial nests in providing shelter for larger chicks against heavy rain and predators. Ideally, artificial nests should provide solutions to all environmental challenges faced by nesting birds and these challenges will vary both within and between species. In African Penguins breeding in Algoa Bay, the environmental challenges change as the breeding season progresses. During incubation at the end of the austral summer in February and March, when we conducted our study, high temperatures are likely to be the primary factor causing low success in exposed nests as parent birds are exposed to heat stress and may abandon their eggs and small chicks. However, during chick-rearing from April to June, rain, storms and predation lead to the death of unguarded chicks. Both artificial nest types appear to provide some shelter from rain, storms and predation such that chick survival is higher than in exposed nests later in the season (Table 1, Pichegru Reference Pichegru2013). However, our findings from this study suggest that fibreglass nests fail to provide adequate protection from the harsh thermal conditions found during incubation and brooding at the start of the breeding season. Cement nests do appear to provide some shelter from direct radiation, yet temperatures are high and humidity low, which may increase thermoregulation cost in penguins breeding in these nests. We suggest therefore that further improvements to the design of cement nests must be made, with for example thicker cement walls which would increase the insulation property of the nest, to better mimic natural burrows and avoid these demanding environmental conditions. Such improved nests may lead to even higher hatching, and hence breeding, success.
While vegetation cover had no effect on internal temperatures for fibreglass nests, our data (Figure 5) suggest that providing shade with natural vegetation or through artificial means is another management option that bears further investigation. A shading effect could be similar to that of orientation of nest boxes, which influenced greatly temperatures in artificial boxes for terrestrial birds (Ardia et al. Reference Ardia, Perez and Clotfelter2006, Charter et al. Reference Charter, Meyrom, Leshem, Aviel, Izhaki and Motro2010, Catry et al. Reference Catry, Franco and Sutherland2011). While it is probably safe to assume similar small benefits of vegetation cover over the longer term on cement nests, further artificial nest materials could also be considered to match the conditions experienced by birds nesting in natural burrows. For example, in Lesser Kestrels Falco naumanni wooden nest boxes had temperatures far in excess of those made of adobe, cement and stone (Catry et al. Reference Catry, Franco and Sutherland2011). As a result, mortality of chicks in wooden boxes was higher during periods of high ambient temperatures, and those that did survive had a lower growth rate and poorer body condition at fledging due to the cost of thermoregulation (Catry et al. Reference Catry, Franco and Sutherland2011). For African Penguins in contrast, wood being moisture-absorbent might be more beneficial than fibreglass burrows and has been in use at Robben Island since 2001 (Sherley et al. Reference Sherley, Barham, Barham, Leshoro and Underhill2012).
Conclusion
Sutherland et al. (Reference Sutherland, Pullin, Dolman and Knight2004) highlight the importance of making conservation decisions based on evidence and the current study will aid conservation practitioners in southern Africa as they endeavour to make practical interventions to address these threats, in this case by improving the design of artificial nests. Artificial nests for threatened avian populations have proven successful in the past, provided that the design and placement of the nest is adequate to counter the environmental challenges posed to birds (e.g. Perriman and Steen Reference Perriman and Steen2000, Catry et al. Reference Catry, Alcazar, Franco and Sutherland2009, Reference Catry, Franco and Sutherland2011, Libois et al. Reference Libois, Gimenez, Oro, Minguez, Pradel and Sanz-Aguilar2012). This study further supports the idea that cement nests may be the better artificial nest option for African Penguins (Pichegru Reference Pichegru2013) since they appear to provide some protection from radiation during incubation and from rain and predation during chick-rearing. However they are far from a complete panacea, as temperatures remain unnaturally high and humidity low. Vegetation cover will improve over time and may increase the capacity of these nests to provide adequate shelter. Nevertheless, additional research is necessary towards engineering an artificial nest that can better mimic the conditions of natural burrows, with more buffered temperatures, perhaps through better insulation, and higher relative humidity. Tests of different materials should now be conducted to determine alternative building or lining materials that can maintain higher humidity levels within the nest, while also considering factors such as durability and hygiene (Kemper et al. Reference Kemper, Underhill, Roux and Kirkman2007). It is also important to determine the thermo-neutral zone for African Penguins, in case it differs from Humboldt Penguins. This could be done by studying the thermoregulatory behaviour of penguins to determine when they are heat-stressed. This would be an appropriate indicator, since it is through their behaviour that they can dissipate energy, conserve water, and reduce thermal stress (Lustick Reference Lustick and Whittow1984, Davenport Reference Davenport1992, Dawson and Whittow Reference Dawson, Whittow and Whittow2000).
Acknowledgements
We wish to thank SANParks for some data collection and assistance with transport and logistics for the field work. During the study, BL was funded by the Weissman International Internship Program, and LP by BirdLife South Africa through “the African Penguin Species Champion” project of the Charl van der Merwe Trust. We also thank Pablo Yorio, Esteban Frere and one anonymous referee for constructive comments on the manuscript.
