Hostname: page-component-78c5997874-ndw9j Total loading time: 0 Render date: 2024-11-06T05:10:17.773Z Has data issue: false hasContentIssue false
  • English
  • Français

Optimization of the rapping process of an intermittent electrostatic precipitator

Published online by Cambridge University Press:  19 December 2007

F. Miloua ,
A. Tilmatine ,
R. Gouri ,
N. Kadous  and
L. Dascalescu
F. Miloua
Affiliation:
Research unit “Electrostatics and High-Voltage Engineering”, IRECOM Laboratory University of Sidi-Bel-Abbes, Algeria
A. Tilmatine*
Affiliation:
Research unit “Electrostatics and High-Voltage Engineering”, IRECOM Laboratory University of Sidi-Bel-Abbes, Algeria
R. Gouri
Affiliation:
Research unit “Electrostatics and High-Voltage Engineering”, IRECOM Laboratory University of Sidi-Bel-Abbes, Algeria
N. Kadous
Affiliation:
Research unit “Electrostatics and High-Voltage Engineering”, IRECOM Laboratory University of Sidi-Bel-Abbes, Algeria
L. Dascalescu
Affiliation:
IUT of Angoulême, Univ. of Poitiers, France
*
[email protected]
Get access

Abstract

Intermittent operation mode is specific to electrostatic precipitators (ESP) used in workshops where the polluting product is produced in a discontinuous way. The rapping system is necessary in order to ensure a continuous and effective operation of a dry electrostatic precipitator, but causes at the same time, a problem of re-entrainment of dust and thus the degradation of filtration efficiency. The objective of this paper is to propose a procedure based on the methodology of experimental designs (Tagushi's Methodology) aiming at optimizing the rapping process; it consists to determine optimal values of rapping, i.e. the moment, the position and the force of rapping. Several “one-factor-at-a-time" experimental designs followed by a Full Factorial design, made it possible to model the process and to analyze interactions between the factors. The experiments were carried out on a laboratory experimental device which simulates an industrial precipitator with intermittent operation.

Keywords

Type
Research Article
Information
The European Physical Journal - Applied Physics , Volume 41 , Issue 1 , January 2008 , pp. 81 - 85
Copyright
© EDP Sciences, 2007

Access options

Get access to the full version of this content by using one of the access options below. (Log in options will check for institutional or personal access. Content may require purchase if you do not have access.)

References

Hoenig, S.A., IEEE Trans. Ind. Appl. 17, 386 (1981) CrossRef
H.J. White, Industrial electrostatic precipitation (Wesley, Reading, MA, 1963)
Takahashi, T., Zukeran, A., Ehara, Y., Ito, T., Takamatu, T., T. IEE Japan 119, 254 (1999)
F. Miloua, N. Kadous, F.Z. Rahou, A. Semmah, A.Tilmatine, J. Mater. Technol. 20 (2005)
D. Brocilo, J.S. Chang, R.D. Findlay, Modelling of electrode geometry effects on dust collection efficiency of-plate electrostatic precipitator, 8th ICESP Conf. (Birmingham, Alabama, USA, 2001), pp. 1–18
Liang, X., Jayaram, S., Berzein, A., Chang, J.S., IEEE Trans. Ind. Appl. 35, 1184 (2002)
Schmid, H.J., Powder Technol. 135–136, 136 (2003) CrossRef
Kogelschartz, Walter Egil Edgar, Advanced computer modelling of electrostatic precipitators, ABB Corporate, November 2001
Research, Switzerland, and Edgar Gerteisen, SCSC, Switzerland
M. Pauthenier, M. Moreau-Hanot, J. Phys. Radium, Ser. 7, 590 (1932)
A. Tilmatine, F. Miloua, N. Kadous, K. Medles, L. Dascalescu, Experimental modelling of electrostatic precipitation using Tagushi's methodology, IEEE/IAS Conference on Electrostatics (Berkeley, California, 6–9 June 2006)
J. Goupy, Modélisation par les plans d'expériences, Technique de l'ingénieur, traité mesure et contrôle, R 275-1
J. Goupy, Plans d'expériences pour surfaces de réponse (Dunod, Paris, 1999)
Software MODDE.05.: Umetrics, Sweden