Hostname: page-component-78c5997874-m6dg7 Total loading time: 0 Render date: 2024-11-19T05:17:31.619Z Has data issue: false hasContentIssue false
  • English
  • Français

Formulation and numerical solution of elastic robot dynamic motion with maximum load carrying capacities

Published online by Cambridge University Press:  09 March 2009

M.H. korayem  and
A. Basu
M.H. korayem
Affiliation:
Department of Mechanical Engineering, University of Wollongong, P.O. Box 1144, Northfield Avenue, Wollongong, NSW, 2522 (Australia)
A. Basu
Affiliation:
Department of Mechanical Engineering, University of Wollongong, P.O. Box 1144, Northfield Avenue, Wollongong, NSW, 2522 (Australia)
Get access Rights & Permissions [Opens in a new window]

Summary

This paper presents a new formulation as well as numerical solution for the problem of finding a point-to-point trajectory with maximum load carrying capacities for flexible manipulators. For rigid manipulators, the major limiting factor in determining the maximum allowable load (mass and mass moment of inertia) is the joint actuator capacity, while the flexibility exhibited by light weight robots or by robots operating at a higher speed dictates the need for an additional constraint to be imposed for situations where precision tracking is required, that is, the allowable deformation at the end effector. The Lagrangian assumed mode method was used to model the manipulator and load dynamics, including both joint and deflection motions. An Iterative Linear Programming (ILP) method is then used to determine the maximum allowable load of elastic robot subject to both constraints, while a general computational procedure for the multiple-link case given arbitrary trajectories is presented in detail. Symbolic derivation and simulation by using a PC-based symbolic language MATHEMATICA® was carried out for a two-link planer robot and the results further confirm the necessity of the dual constraints.

Rough joint flexibility is the dominant source of compliance in today's commercial robots in future robots containing light weight flexible arms link flexibility may become most important. Hence this paper stresses link flexibility rather than joint flexibility.

Keywords

Flexible linksOptimal trajectoryDynamic LoadAccuracy constraintActuator constraint
Type
Article
Information
Robotica , Volume 12 , Issue 3 , May 1994 , pp. 253 - 261
Copyright
Copyright © Cambridge University Press 1994

Access options

Get access to the full version of this content by using one of the access options below. (Log in options will check for institutional or personal access. Content may require purchase if you do not have access.)

References

1. Wang, L.T and Ravani, B., “Dynamic Load Carrying Capacity of Mechanical Manipulators-Part II: Computational Procedure and Applications” Transactions of ASME J. Dynamic System, Measurement and Control 110, 53–61 (1988).CrossRefGoogle Scholar
2. Asada, H., Ma, Z.-D. and Tokumara, H., “Inverse Dynamics of Flexible Robot Arms: Modeling and Computation for Trajectory Control” Transactions of ASME, J. Dynamic System, Measurement and Control 112, 177–185 (1990).CrossRefGoogle Scholar
3. Usors, P.B, Nadria, R. and Mahil, S.S, “A Finite Element/Lagrange Approach to Modeling Lightweight Flexible Manipulators” Transactions of ASME, J. Dynamic System, Measurement and Control 108, 198–205 (1986).CrossRefGoogle Scholar
4. Chang, L.W and Hamilton, J.F, “Dynamics of Robotic Manipulators With Flexible Links” Transactions of ASME J. Dynamic System, Measurement and Control 113, 54–59 (1991).CrossRefGoogle Scholar
5. Shabana, A.A, “Dynamics of Flexible Bodies Using Generalized Newton-Euler Equation” Transactions of ASME J. Dynamic System, Measurement and Control 112, 496–503 (1990).CrossRefGoogle Scholar
6. Bayo, E. and Paden, B., “On trajectory generation for flexible robots” J. Robotic Systems 229–235 (1987).CrossRefGoogle Scholar
7. Sema, M.A and Bayo, E., “Experiments on the Payload-Adaptation of A Flexible One-Link Manipulator with Unknown Payload” Proc. IEEE Int. Conf. Robotics and Automation (1990) pp. 910–913.Google Scholar
8. Book, W.J, “Recursive Lagrangian Dynamics of Flexible Manipulator Arm” International J. Robotics Research 3, No. 3, 87–101 (1984).CrossRefGoogle Scholar
9. Korayem, M.H, and Basu, A., “Synthesis of Flexible Manipulator Dynamic Motions With Maximum Load Carrying Capacities” Proc. Fourteenth Canadian Congress of Applied Mechanics 1 (06 1993) pp. 83–86.Google Scholar
10. Korayem, M.H and Basu, A., “Efficient Elastic Robot Inverse Dynamics Algorithm Using Pc-Based Symbolic Manipulation,” Proc. 12th World Congress International Federation of Automatic Control (IFAC) 3 (07, 1993) pp. 285–288.Google Scholar
11. Korayem, M.H, Yao, Y. and Basu, A., “Dynamic Load Carrying Capacity for A Multi-Link Flexible Arm” Proc. Int. Conf. Control and Robotics Automation 1 (4–7 08, 1992) pp. 79–83.Google Scholar
12. Korayem, M.H, Yao, Y. and Basu, A., “Symbolic Derivation and Dynamic Simulation of Flexible Manipulators” Proc. Int. Conf. on Intelligent Control and Instrumentation 1 (18–21 Feb., 1992) pp. 376–382.Google Scholar
13. Korayem, M.H, Yao, Y. and Basu, A., “Application of Symbolic Manipulation to Inverse Dynamics and Kinematics of Elastic Robots” (In Press).Google Scholar
14. Wolfram, S., MATHEMATICA (Addison-Wesley, Read. ing, Mass., 1991).Google Scholar