Hostname: page-component-cd9895bd7-jkksz Total loading time: 0 Render date: 2024-12-27T01:11:19.089Z Has data issue: false hasContentIssue false
  • English
  • Français

Thin-film Micro-Batteries Based on Metal Nanoparticles

Published online by Cambridge University Press:  03 October 2012

Shuang Peng ,
Wenjun Du ,
Leela Rakesh ,
Axel Mellinger  and
Tolga Kaya
Shuang Peng
Affiliation:
Department of Physics
Wenjun Du
Affiliation:
Department of Chemistry Science of Advanced MaterialsProgram
Leela Rakesh
Affiliation:
Science of Advanced MaterialsProgram Department of Mathematics
Axel Mellinger
Affiliation:
Department of Physics Science of Advanced MaterialsProgram
Tolga Kaya
Affiliation:
Science of Advanced MaterialsProgram School of Engineering and Technology Central Michigan University, Mount Pleasant, MI, 48859, U.S.A.
Get access

Abstract

We proposed the use of Copper (Cu) and Zinc (Zn) nanoparticles as the electrodes for thin-film microbatteries in the applications of micro-scale sensors. Compared to the widely used lithium-based batteries, Cu and Zn nanoparticles are less expensive, less prone to oxidation (thus involving simpler fabrication steps) and flammability, safe to use, and only requires very simple fabrication processes.Even though the voltage output is inherently smaller (∼1V) than conventional lithium-based batteries, it is sufficient for low-voltage Integrated Circuits (IC) technologies such as 130 nm and 90 nm channel length transistor processes.

Commercial paper will be used as the separator to demonstrate the battery capacity. Paper that acts as the separator is slurry-casted with nanoparticles (30-40 nm in size) on both sides. The thickness of the metal nanoparticles-coated thin films and the paper separator are 1 μm and 100 μm, respectively.

The electrodes were developed to achieve high conductivity (lower than 1 (Ω·cm)-1) with smooth surface, good adhesion, and flexibility. The metal nanoparticles will be formulated to slurry solutions for screen printing or ink-jet printing for the battery fabrication. For fabrication purposes, the slurries viscosity is approximately in the range of 10-12 cPs at the operating temperature, a surface tension between 28-33 dynes/cm. During the fabrication process including printing/coating and sintering, reductive environment is required to minimize the oxidation. AFM (Atomic Force Microscopy) and EDS (Energy Dispersive Spectroscopy) results will be employed to demonstrate the surface morphology as well as the percentages of metal oxides. Batteries will be tested with and without an ionic liquid for comparison. Humidity effects on the battery performance will also be discussed.

Different geometries that are designed to make the batteries with higher voltage or charge will be proposed. Characterization results will include the open-circuit voltage, dielectric property, charging and discharging curve, capacitance and capacity, AFM of the surface test, EDS of the electrodes and the SEM (Scanning Electron microscopy) of the particles.Ourresearch suggest that conductive paper can be scalable and could make high-performance energy storage and conversion devices at low cost and would bring new opportunities for advanced applications.

Keywords

microelectro-mechanical (MEMS)dielectricnanostructure
Type
Articles
Information
MRS Online Proceedings Library (OPL) , Volume 1440: Symposium O – Next-Generation Energy Storage Materials and Systems , 2012 , mrss12-1440-o09-27
Copyright
Copyright © Materials Research Society 2012

Access options

Get access to the full version of this content by using one of the access options below. (Log in options will check for institutional or personal access. Content may require purchase if you do not have access.)

References

REFERENCES

Isabel, F., Bruno, B., Nuno, C., Pedro, B., Elvira, F., and Rodrigo, M. J. Display Technology, 6, 8 (2010)Google Scholar
Ho, C. C., Evans, J. W., and Wright, P. K., J. Micromech. Microeng. 20, 104009. (2010).CrossRefGoogle Scholar
Ho, C. C., Murata, K., Steingart, D. A., Evans, J. W., and Wright, P. K., J. Micromech. Microeng. 19, 094013 (2009).CrossRefGoogle Scholar
Gamerith, S., Klug, A., Scheiber, H., Scherf, U., Moderegger, E., and Emil, J. W., Advanced Functional Materials. 17, 3111–3118 (2007).CrossRefGoogle Scholar
Hu, L. B., Choi, J. W., Yang, Y., Jeong, S., Mantia, F. L., Cui, L. F., and Cui, Y., PNAS 0908858106. (2009).Google Scholar
Yu, E. K., Piao, L. H., and Kim, S. H., Bull. Korean Chem. Soc. 32. 11 (2011)Google Scholar
Kim, H. S., Dhage, S. R., Shim, D. E., and Hahn, H. T., Applied Physics A. 97, 791–798 (2009).CrossRefGoogle Scholar
Han, W. S., Hong, J. M., Kim, H. S., and Song, Y. W., Nanotechnology. 22, 395705. (2011).CrossRefGoogle Scholar
Kang, J. S., Kim, H. S., Ryu, J., Hahn, H. T., Jang, S., and Joung, J. W., J Mater. Sci: Mater Electron. 21, 1213–1220. (2010).Google Scholar
Lee, D. J., Park, S. H., Jang, S., Kim, H. S., Oh, J. H., and Song, Y. W., J. Micromech. Microeng. 21, 125023 (2011).CrossRefGoogle Scholar
Kulkarni, D.P, Das, D.K., Chukwu, G.A. Journal of nanoscience and nanotechnology. 6, 1150–1154. (2006).CrossRefGoogle Scholar
Bicerano, J., Douglas, J.F., Brune, D.A.. Journal of Macromolecular Science Review. 39: 561–642. (1999).CrossRefGoogle Scholar