Hostname: page-component-cd9895bd7-dzt6s Total loading time: 0 Render date: 2024-12-27T18:48:21.332Z Has data issue: false hasContentIssue false
  • English
  • Français

Synthesis of Quasicrystal Phases by Mechanical Alloying of Ti45+xZr38-XNi17 (-4≤ X ≤16) Powder Mixtures, and Their Hydrogen Storage Properties

Published online by Cambridge University Press:  01 February 2011

Akito Takasaki ,
Naoki Imai  and
Kenneth F. Kelton
Akito Takasaki
Affiliation:
Department of Mechanical Engineering, Shibaura Institute of Technology, Fukasaku, Saitama 337–8570, Japan
Naoki Imai
Affiliation:
Graduate School, Shibaura Institute of Technology, Fukasaku, Saitama 337–8570, Japan
Kenneth F. Kelton
Affiliation:
Department of Physics, Washington University, St. Louis, Missouri 63130, USA
Get access

Abstract

Mechanical alloying of Ti45+xZr38-xNi17 (-4 ≤ x ≤ 16) elemental powder mixtures leads to the formation the amorphous phase, but subsequent annealing at 833 K causes the formation of icosahedral (i) quasicrystal and the Ti2Ni-type crystal phases. The α-Ti phase is also produced in Ti-rich powders after annealing. Both the quasilattice constant of the i-phase and the lattice parameter of the Ti2Ni-type crystal phase decrease monotonically with increasing substituted amount of Ti because of the smaller radius of the Ti atom. The maximum hydrogen concentration in the i-phase in all powder compacts, after electrochemical hydrogenation in a KOH solution, is almost the same, about 63 at% ([H] / [M] ≈ 1.7). The onset temperature of hydrogen desorption is about 570 K (at a heating rate of 5 K/min) for all powders, but the temperature for the maximum hydrogen desorption rate increases with increasing Ti concentration in the powders, suggesting that some hydrogen atoms might be more strongly bound in the quasilattice where the original Zr sites become occupied by Ti atoms.

Type
Research Article
Information
MRS Online Proceedings Library (OPL) , Volume 805: Symposium LL – Quasicrystals , 2003 , LL10.4
Copyright
Copyright © Materials Research Society 2004

Access options

Get access to the full version of this content by using one of the access options below. (Log in options will check for institutional or personal access. Content may require purchase if you do not have access.)

References

REFERENCES

1. Viano, A.M., Stroud, R.M., Gibbons, P.C., McDowell, A.F., Conradi, M.S., and Kelton, K.F., Phys. Rev., B, 51, 12026 (1995).Google Scholar
2. Kelton, K.F., and Gibbons, P.C., MRS Bull., 22, 69 (1997).Google Scholar
3. Takasaki, A., Han, C.H., Furuya, Y., and Kelton, K.F., Phil. Mag. Lett., 82, 353 (2002).Google Scholar
4. Takasaki, A., and Kelton, K.F., J. Alloys Comps., 347, 295 (2002).Google Scholar
5. Sadoc, A., Kim, J.Y. and Kelton, K.F., Phil. Mag. A, 79, 2763 (1999).Google Scholar
6. Sadoc, A., Majzoub, E.H., Huett, V.T. and Kelton, K.F., J. Alloys Comps., 356–357, 96 (2003).Google Scholar
7. Takasaki, A., Kikuchi, K., and Furuya, Y., Mater. Trans., JIM, 41, 306 (2000).Google Scholar
8. Elser, V., Phys. Rev. B32, 4892 (1985).Google Scholar
9. Gibbons, P.C., and Kelton, K.F., in Physical Properties of Quasicrystals, ed. Stadnik, Z.M., (Springer, 1999) pp. 403–431.Google Scholar
10. Viano, A.M., Majzoub, E.H., Stroud, R.M., Kramer, M.J., Misture, S.T., Gibbons, P.C. and Kelton, K.F., Phil. Mag. A, 78, 131 (1998)Google Scholar