Hostname: page-component-6bf8c574d5-vmclg Total loading time: 0 Render date: 2025-02-20T14:27:26.574Z Has data issue: false hasContentIssue false
  • English
  • Français

Sputtered ZnTe:N and ZnO:Al for Solar Cell Electrodes and Recombination Junctions

Published online by Cambridge University Press:  01 February 2011

Jennifer Drayton ,
V. Parikh ,
G. Rich ,
A. Gupta ,
T. Osborn ,
R.G. Bohn ,
A.D. Compaan ,
B.E. McCandless  and
P.D. Paulson
Jennifer Drayton
Affiliation:
Department of Physics and Astronomy, The University of Toledo, Toledo, OH
V. Parikh
Affiliation:
Department of Physics and Astronomy, The University of Toledo, Toledo, OH
G. Rich
Affiliation:
Department of Physics and Astronomy, The University of Toledo, Toledo, OH
A. Gupta
Affiliation:
Department of Physics and Astronomy, The University of Toledo, Toledo, OH
T. Osborn
Affiliation:
Department of Chemistry, The University of Toledo, Toledo, OH
R.G. Bohn
Affiliation:
Department of Physics and Astronomy, The University of Toledo, Toledo, OH
A.D. Compaan
Affiliation:
Department of Physics and Astronomy, The University of Toledo, Toledo, OH
B.E. McCandless
Affiliation:
Institute of Energy Conversion, The University of Delaware, Newark, DE
P.D. Paulson
Affiliation:
Institute of Energy Conversion, The University of Delaware, Newark, DE
Get access

Abstract

We have used sputtered ZnTe:N and ZnO:Al as transparent electrodes for CdTe based solar cells. ZnTe:N is reactively sputtered with 3% N2 in the sputter gas. The ZnTe:N films typically have transmission near 85% above 750 nm and resistivity as low as 10 ohm-cm with fine grains of approximately 30 nm diameter. ZnO:Al is sputtered from a ZnO:Al2O3 (2%) target. The ZnO:Al films have resistivity as low as 4 × 10-4 ohm-cm with 80-95% transmission over the visible spectrum. To test the stability of the films, ZnTe:N films were annealed in argon, dry air and nitrogen at a range of temperatures from 200°C to 500°C. Annealing decreased the resistivity for temperatures up to 350°C and increased for temperatures greater than 350°C. ZnO:Al films were annealed in dry air at temperatures from 300°C to 550°C. Though the resistivity increased at higher annealing temperatures, there was no change in the transmission. Important to the function of a tandem solar cell is a transparent contact, like ZnTe:N/ZnO:Al, to replace the traditional metal contact to the CdS/CdTe solar cell. We investigate the ZnTe:N/ ZnO:Al bilayer as a possible recombination junction. The rf sputtered ZnTe:N and ZnO:Al films were characterized by AFM, STM, XRD, transmission, 4-point probe, and Hall measurements.

Type
Research Article
Information
MRS Online Proceedings Library (OPL) , Volume 763: Symposium B – Compound Semiconductor Photovoltaics , 2003 , B8.11
Copyright
Copyright © Materials Research Society 2003

Access options

Get access to the full version of this content by using one of the access options below. (Log in options will check for institutional or personal access. Content may require purchase if you do not have access.)

References

1. Drayton, J., Taylor, C., Gupta, A., Bohn, R.G., Rich, G., Compaan, A.D., McCandless, B.E., Rose, D., IEEE PVSC-2002, pp. 539–542.Google Scholar
2. Haug, F., Geller, Z., Zogg, H., and Tiwari, A., J. Vac. Sci. Technol. A 19(1), 2001, pp. 171–174.Google Scholar
3. Sze, S.M., Physics of Semiconductor Devices, 2nd ed, John Wiley & Sons (New York), pp. 516–520, 1981.Google Scholar