Hostname: page-component-586b7cd67f-gb8f7 Total loading time: 0 Render date: 2024-11-29T08:03:22.420Z Has data issue: false hasContentIssue false
  • English
  • Français

Quxatitative Theory of Seasitization

Published online by Cambridge University Press:  21 February 2011

Thomas M. Devine
Thomas M. Devine*
Affiliation:
Materialsand Chemical Sciences Division Lawrence Berkeley Laboratory, Department of Materials Science and Mineral EngineeringUniversity of California Berkeley, CA94720
Get access

Abstract

The chromium composition along the grain boundaries of sensitized austenitic stainless steel are calculated using several different quantitative theories of sensitization. The results of the calculations are compared to measured values of the chromium composition along the grain boundary in an effort to assess the validity of the various theories. The experimental results point out two facts not previously emphasized in prior studies: (1) the amount of carbide precipitation required to sensitize austenitic stainless steel is small; (2) significant de-sensitization does not occur until after large amountsof carbide precipitation have occurred.

Type
Research Article
Information
MRS Online Proceedings Library (OPL) , Volume 125: Symposium N – Materials Stability and Environmental Degradation , 1988 , 235
Copyright
Copyright © Materials Research Society 1988

Access options

Get access to the full version of this content by using one of the access options below. (Log in options will check for institutional or personal access. Content may require purchase if you do not have access.)

References

REFERENCES

(1) Strauss, B., Schottky, H. and Hinnuber, J., Z. Anorg. Allgem. Chem., 118 p, 309 (1930).Google Scholar
(2) Bain, E.C., Aborn, R.H. and Rutherford, J.J.B., Trans. Am. Soc. Steel Treat., 21, p.481 (1933).Google Scholar
(3) Hall, E.L. and Briant, C.L., Met.TransA, 15A, p. 793 (1984).Google Scholar
(4) Devine, T.M., submitted forpublicationin Corrosion.Google Scholar
(5) Stawstrom, C. and Hillert, M., J. I.S.I., 207, p.77 (1969).Google Scholar
(6) Tedmon, C.S., Vermilyea, D.A. and Rosolowski, J. H., J. Electrochem Soc.. 118, p, 192 (1971).Google Scholar
(7) Fullman, R.L., ActaMet.30, p.1407 (1982).Google Scholar
(8) E Hall, L. and Briant, C.L., paper # 8408–039, Presented at the International Symposium on Interface Migration and Control of Microstructure, TMS/AIME Fall Meeting, Detroit, Mich., S ept. 17–21, 1984.Google Scholar
(9) Devine, T.M., submitted forpublicationin CorrosionScenceGoogle Scholar
(10) Devine, T. M., Submitted for publicationin Corrosion.Google Scholar
(11) Devine, T M., accepted forpublication in w.Google Scholar
(12) Lewis, M.M. and Hattersley, B., Acta Met., 13, p.L159 (1965).CrossRefGoogle Scholar
(13) Singhal, L.K. and Martin, J.W., Trans. Met. Soc. AIME, 242, p. 814 (1968).Google Scholar
(14) Adamson, J.P. and Martin, J. W., Acta Met., 19, p. 1015 (1971).CrossRefGoogle Scholar
(15) Richardson, F.D., IS.I., 167, p.3 (1953).Google Scholar
(16) Wagner, C., “Thermodynamics of Alloys”, p. 51, Addison-Wesley, Reading, MA (1952).Google Scholar
(17) Chipman, J. and Brush, E. F., Trans.TMS-AIME. 242, p.35(1968).Google Scholar
(18) Heckler, A. J. and Winchell, P.C., Trans.TMS-AIM, 227, p. 732 (1963).Google Scholar
(19) Natesan, K. and Kassner, T.F., Met. Trans 4., p.2557 (1973).Google Scholar
(20) Kaufman, L. and Nesor, H., Z.MeWa., 64, p.249 (1973).Google Scholar
(21) Hasebe, M. and Nishizawa, T., in “Applications of Phase Diagrams in Metallurgy and Ceramics 2”, Carter, G.C., ed., NBS Special Publication 469, p. 911 (1978).Google Scholar
(22) Devine, T.M., Met Trans,. A, 11A, p.791 (1980).Google Scholar
(23) Goodell, P.G., unpublished research: as cited in reference (6).Google Scholar
(24) Bendure, R.J., Ikenberry, L.C. and Waxweiler, J.H., Tran.TMSAIME, 221, p. 1032 (1961).Google Scholar