Hostname: page-component-586b7cd67f-2brh9 Total loading time: 0 Render date: 2024-11-26T05:31:17.773Z Has data issue: false hasContentIssue false
  • English
  • Français

Quantitative Determination of the Mechanical Stresses in BEoL Films and Structures on Si Wafers with Sub-micron Spatial Resolution by fibDAC

Published online by Cambridge University Press:  30 July 2012

Sven Rzepka ,
Dietmar Vogel ,
Ellen Auerswald  and
Bernd Michel
Sven Rzepka
Affiliation:
Micro Materials Center, Fraunhofer ENAS, Technologie-Campus 3, 09126 Chemnitz, Germany, [email protected]
Dietmar Vogel
Affiliation:
Micro Materials Center, Fraunhofer ENAS, Technologie-Campus 3, 09126 Chemnitz, Germany, [email protected]
Ellen Auerswald
Affiliation:
Micro Materials Center, Fraunhofer ENAS, Technologie-Campus 3, 09126 Chemnitz, Germany, [email protected]
Bernd Michel
Affiliation:
Micro Materials Center, Fraunhofer ENAS, Technologie-Campus 3, 09126 Chemnitz, Germany, [email protected]
Get access

Abstract

The fibDAC stress analysis method, a new tool for local stress measurement, has been applied to patterned BEoL structures after being validated at complete films by established industrial methods like wafer bow measurement. The new tool uses focused ion beam (FIB) to mill a narrow trench of down to 30 nm width into the surface of the structure under investigation to trigger stress relief in its vicinity. Capturing the corresponding deformation by high resolution SEM micrographs and local digital image correlation, the original stress can be determined by simulating the stress relief process by automated finite element analyses. Simultaneously, the extraction of key material parameters of the film like Young’s modulus and Poisson’s ratio is possible.

The spatial resolution of the fibDAC stress analysis method is 1 μm and better. It has been demonstrated at arrays of BEoL interconnects. The magnitude of the local stresses inside the metal traces has been shown to be substantially different to those occurring in the dielectrics between the lines. Such a spatial resolution clearly outperforms all established industrial methods.

Keywords

stress/strain relationshipscanning electron microscopy (SEM)simulation
Type
Articles
Information
MRS Online Proceedings Library (OPL) , Volume 1428: Symposium C – “Interconnect Challenges for CMOS Technology--Materials, Processes and Reliability for Downscaling, Packaging and 3D Stacking” , 2012 , mrss12-1428-c08-02
Copyright
Copyright © Materials Research Society 2012

Access options

Get access to the full version of this content by using one of the access options below. (Log in options will check for institutional or personal access. Content may require purchase if you do not have access.)

References

REFERENCES

1. Freund, L.B., Suresh, S.; Film stress and substrate curvature, in Thin Film Materials, Cambridge University Press, 2003, pp. 86–153.Google Scholar
2. Geisler, H. et al. ;Temperature-dependent stress measurements at inlaid copper interconnect lines, in Stress-Induced Phenomena in Metallization, AIP Conference Proceedings, Vol. 817, Meville, 2006, pp. 277–287.Google Scholar
3. Neels, A., Dommann, A.; Advanced in- and out-off plane high resolution X-ray strain analysis on MEMS, Techn. Proc. NSTI Nanotech; Anaheim, 2010, Vol. 2, pp. 182–185.Google Scholar
4. Song, Xu et al. ; Experimental/modeling study of residual stress in Al/SiCp bent bars by synchrotron XRD and slitting eigenstrain methods, Materials Science Forum, Vols. 571-572, 2008, pp. 277-282.Google Scholar
5. Wilkinson, A.J., Meaden, G., Dingley, D.J.; High-resolution elastic strain measurement from electron backscatter diffraction patterns: new level of sensitivity, Ultramicroscopy, Vol. 106, 2006, pp. 307–313.Google Scholar
6. Sabaté, N., et al. ; Measurement of residual stresses in micromachined structures in a micro region, Appl. Physics Letters 88, 071910, 2006.Google Scholar
7. Vogel, D. et al. ; Localized stress measurements – a new approach covering needs for advanced micro and nanoscale system development, Proc.. of ECTC 2007, Reno, pp. 1490–1497.Google Scholar
8. Digital Image Correlation VEDDAC 5.1-User’s Manual, Chemnitzer Werkstoffmechanik GmbH, Chemnitz, Germany, 2011 Google Scholar
9. Bressan, J.D., Tramontin, A., Rosa, C.: Modeling of nanoindentation of bulk and thin film by finite element method; Wear, Vol. 258, 2005, pp. 115–22Google Scholar
10. OptiSLangTM 3.2, User’s Manual; Dynardo GmbH, Weimar, Dec. 2011 Google Scholar