Hostname: page-component-586b7cd67f-2brh9 Total loading time: 0 Render date: 2024-11-26T20:32:47.062Z Has data issue: false hasContentIssue false
  • English
  • Français

Pt Hillock Formation and Decay

Published online by Cambridge University Press:  15 February 2011

Scott R. Summerfelt ,
Dave Kotecki ,
Angus Kingon  and
H.N. Al-Shareef
Scott R. Summerfelt
Affiliation:
Materials Science Laboratory, Texas Instruments Inc., Dallas TX
Dave Kotecki
Affiliation:
IBM Microelectronics Div., Hopewell Junction NY
Angus Kingon
Affiliation:
Dept. MS&E, North Carolina State University, Raleigh NC
H.N. Al-Shareef
Affiliation:
Dept. MS&E, North Carolina State University, Raleigh NC
Get access

Abstract

The formation of Pt hillocks during high temperature processing is a problem when using Pt as a bottom electrode for high dielectric constant materials. The hillock height is frequently larger than the dielectric thickness, degrading the leakage current of the device. In this work, Pt was deposited by electron beam evaporation on in-situ formed 40 nm ZrO2 coated SiO2 / Si substrates. The samples were then annealed at temperatures between 400°C and 700°C for times ranging from 2 min to 40 min. The surface roughness was measured by atomic force microscopy (AFM). The surface was characterized using Ra, RMS and Zmax over 5 μm × 5μm regions. Zmax is sensitive to hillock formation and Ra is sensitive to changes in general surface roughness. Analysis of Zmax indicates that 100 nm Pt / ZrO2 deposited at 315°C forms hillocks above 450°C during initial heatup. Subsequently, the hillocks decay for temperatures of 600°C and above such that they are almost gone after a 30 min air anneal. In-situ wafer stress measurements of Pt / ZrO2 were performed in O2 at temperatures up to 650°C. The Pt relaxes above 500°C in O2.

Type
Research Article
Information
MRS Online Proceedings Library (OPL) , Volume 361: Symposium I2 – Ferroelectric Thin Films IV , 1994 , 257
Copyright
Copyright © Materials Research Society 1995

Access options

Get access to the full version of this content by using one of the access options below. (Log in options will check for institutional or personal access. Content may require purchase if you do not have access.)

References

REFERENCES

1. Olowolafe, J.O., Jones, R.E. Jr, Campbell, A. C., , Hegde, R.I., Mogab, C.J. and Gregory, R.B., J. Appl. Phys. 73 1764–1772 (1993).Google Scholar
2. Hren, P.D., Rou, S.H., Al-Shareef, H.N., Ameen, M.S., Auciello, O. and Kingon, A.I., Integrated Ferroelelctrics 2 311–325 (1992).Google Scholar
3. Hren, P.D., Al-Shareef, H.N., Rou, S.H., Kingon, A.I., Buaud, P. and Irene, E.A., Mat. Res. Soc., Symp. Proc. 260 575–581 (1992).Google Scholar
4. Al Shareef, H.N., Gifford, K.D., Hren, P.D., Rou, S.H., Auciello, O. and Kingon, A.I., Integrated Ferroelelctrics 3, 259–263 (1993).Google Scholar
5. Spierings, G.A.C.M., Dormans, G.J.M., Moors, W.G.J., Ulenaers, M.J.E. and Larsen, P.K., Preprint (1994).Google Scholar
6. Sreenivas, K., Reaney, I., Maeder, T., Setter, N., Jagadish, C. and Elliman, R.G., J. Appl. Phys. 75, 232–239 (1994).Google Scholar
7. d'Heurle, F., Int. Mater. Rev. 34, 53 (1989).Google Scholar
8. Ericson, F., Kristensen, N., Schweitz, J.-A. and Smith, U., J. Vac. Sci. Technol. B 9 58–63 (1991).Google Scholar