Hostname: page-component-cd9895bd7-jn8rn Total loading time: 0 Render date: 2024-12-27T02:37:32.629Z Has data issue: false hasContentIssue false
  • English
  • Français

Performance of Ultra Hard Carbon Wear Coatings on Microgears Fabricated by Liga

Published online by Cambridge University Press:  10 February 2011

Joel W. Ager III ,
Othon R. Monteiro ,
Ian G Brown ,
David M. Follstaedt ,
James A. Knapp ,
Michael T. Dugger  and
Todd R. Christenson
Joel W. Ager III
Affiliation:
Lawrence Berkeley National Laboratory, Berkeley, CA 94720
Othon R. Monteiro
Affiliation:
Lawrence Berkeley National Laboratory, Berkeley, CA 94720
Ian G Brown
Affiliation:
Lawrence Berkeley National Laboratory, Berkeley, CA 94720
David M. Follstaedt
Affiliation:
Sandia National Laboratory, MS 1056, PO Box 5800, Albuquerque, NM 87185
James A. Knapp
Affiliation:
Sandia National Laboratory, MS 1056, PO Box 5800, Albuquerque, NM 87185
Michael T. Dugger
Affiliation:
Sandia National Laboratory, MS 1056, PO Box 5800, Albuquerque, NM 87185
Todd R. Christenson
Affiliation:
Sandia National Laboratory, MS 1056, PO Box 5800, Albuquerque, NM 87185
Get access

Abstract

Stiction and friction are of concern for the reliable, long-term application of Ni-alloy micromachines. We have found that the application of a 30 - 70 nm hard carbon coating produces a significant reduction in the friction coefficient and wear rate of electroformed Ni substrates in reciprocating sliding contact under simulated MEMS operating conditions. To evaluate the performance of coated components, a series of 70-μm-thick microgears ranging in diameter from 0.2 to 2.2 mm were fabricated from electroformed Ni via standard LIGA processes and fixtured on posts in preparation for the coating procedure. A pulsed vacuumarc deposition process was used to deposit a carbon coating on the gears with the plasma incident at a shallow angle to the gears' top surface. A sample bias of −2 keV was used in order to produce a coating with relatively low stress and good adhesion while maintaining high hardness. This coating process is known to be somewhat comformal to the component surfaces. The coating uniformity, particularly in the high-aspect-ratio areas between the gear teeth, was evaluated with micro-Raman spectroscopy. It is shown that the coating can be applied uniformly on the top gear surface. Between the gear teeth the coating was the same thickness as on top of the gear down to a point 50 μm below the top surface. Below that point (i.e. between 50 and 70 μm), the coating thickness is somewhat thinner, but is still present. These results demonstrate that it is possible to a deposit hard carbon coating on microgears to reduce friction and wear in micromachines.

Type
Research Article
Information
MRS Online Proceedings Library (OPL) , Volume 546: Symposium AA – Materials Science of Microelectromechanical Systems (MEMS)… , 1998 , 115
Copyright
Copyright © Materials Research Society 1999

Access options

Get access to the full version of this content by using one of the access options below. (Log in options will check for institutional or personal access. Content may require purchase if you do not have access.)

References

1. Becker, E. W., Ehrfeld, W., Hagmann, P., Maner, A. and Münchmeyer, D., Microelectron. Eng. 4, 35 (1986).Google Scholar
2. Guckel, H., Skrobis, K. J., Klein, J. and Christenson, T. R., J. Vac. Sci. Technol. A 12, 2559 (1994).Google Scholar
3. Bhushan, B., Tribology and Mechanics of Magnetic Storage Devices, (Springer, New York, 1990).Google Scholar
4. Follstaedt, D. M., Knapp, J. A., Myers, S. M., Dugger, M. T., Friedmann, T. A., Sullivan, J. P., Christenson, T., Ager, J. W. III, Monteiro, O. R., and Brown, I. G., “Energetic particle synthesis of metastable layers for superior mechanical properties,” Mater. Res. Soc. Proc., Fall, 1997, in press.Google Scholar
5. Anders, S., Anders, A., Brown, I.G., Wei, B., Komvopoulos, K., Ager, J.W. III, and Yu, K.M., Surf. Coatings Tech. 68 388–393 (1994).Google Scholar
6. Pharr, G. M., Callahan, D. L., McAdams, S. D., Tsui, T. Y., Anders, S., Anders, A., Ager, J. W. III, Brown, I. G., Bhatia, C. S., Silva, S. R. P., and Robertson, J., Appl. Phys. Lett 68, 779–781 (1996).Google Scholar