Hostname: page-component-586b7cd67f-gb8f7 Total loading time: 0 Render date: 2024-11-29T07:41:56.289Z Has data issue: false hasContentIssue false

Microstructure and Electrical Characteristics of Plasma Sprayed Thick Film Mn-Co-Ni Oxide Thermistor

Published online by Cambridge University Press:  01 February 2011

Shanshan Liang
Affiliation:
[email protected], State University of New York, Stony Brook, Department of Materials Science and Engineering, Rm 105, Old Engineering,, Stony Brook University, Stony Brook, NY, 11794-2275, United States, 631-632-4511
Bhuvaragasamy Ravi
Affiliation:
[email protected], State University of New York, Stony Brook, Department of Materials Sciences and Engineering, United States
Sanjay Sampath
Affiliation:
[email protected], State University of New York, Stony Brook, Department of Materials Sciences and Engineering, United States
Richard J. Gambino
Affiliation:
[email protected], State University of New York, Stony Brook, Department of Materials Sciences and Engineering, United States
Get access

Abstract

Mn-Co-Ni-O spinel, owing to its large temperature dependant resistivity, is an attractive ternary system for negative temperature coefficient (NTC) thermistor applications, particularly in oxygen rich environments. This research explores the potential of plasma spray as a method for the fabrication of thick film Mn-Co-Ni-O thermistors. Nanostructured Mn-Co-Ni-O spinel powders were synthesized by gel combustion method and were air-plasma-sprayed on to alumina substrates. The as-sprayed deposit formed a rocksalt structure rather than a cubic spinel structure. Annealing in air at 600°C for 3 hours resulted in transformation to the spinel structure while higher temperature annealing resulted in phase separation of rocksalt phase at 1250°C and recombination into spinel monophase at 1350°C. Temperature dependent measurement of resistivity showed -4 to -1% temperature coefficient of resistivity (TCR) from room temperature to 250oC with high reproducibility, making the low temperature annealed coating suitable in thermistor applications.

Type
Research Article
Copyright
Copyright © Materials Research Society 2006

Access options

Get access to the full version of this content by using one of the access options below. (Log in options will check for institutional or personal access. Content may require purchase if you do not have access.)

References

REFERENCES

[1] Arima, H., in Thick Film Sensors, edited by Prudenziati, M. (Elsevier Science B.V., 1994), p. 127149.Google Scholar
[2] Baliga, S. and Jain, A. L., Materials Letters 8, 175, (1989).Google Scholar
[3] Dannenberg, R., Baliga, S., Gambino, R. J., King, A. H., and Doctor, A. P., Journal of Applied Physics 86, 514–523, (1999).Google Scholar
[4] Baliga, S. and Jain, A. L., Materials Letters 11, 226–228, (1991).Google Scholar
[5] Parlak, M., Hashemi, T., Hogan, M. J., and Brinkman, A. W., Journal of Materials Science Letters 17, 1995, (1999).Google Scholar
[6] Kukuruznyaka, D. A., Bulkley, S. A., Omlanda, Kimberly A., Ohuchi, F. S., and Gregg, M. C., Thin Solid Films 385, 89, (2001).Google Scholar
[7] Gambino, R. J., Raja, M. M., Sampath, S., and Greenlaw, R., IEEE Sensors Journal 4, 764767, (2004).Google Scholar
[8] Sampath, S., Longtin, J., Gambino, R. J., Herman, H., Greenlaw, R., and Tormey, E., in Direct-Write Technologies for Rapid Prototyping : Applications to Sensors, Electronics, and Passivation Coatings, edited by Chrisey, D. (Academic Press, 2002), p. 261302.Google Scholar
[9] Yan, Q. Y., Gambino, R. J., and Sampath, S., IEEE Transactions on Magnetics 40, 33463351, (2004).Google Scholar
[10] Meguro, T., Abe, Y., Yokoyama, T., Murosawa, S., Komeya, K., and Tatami, J., Japanese Journal of Applied Physics Part 1-Regular Papers Short Notes & Review Papers 40, 50415045, (2001).Google Scholar
[11] Györgyfalva, G. D. C. C. d. and Reaney, I. M., Journal of the European Ceramic Society 21, 2145, (2001).Google Scholar
[12] Bodak, O., Akselrud, L., Demchenko, P., Kotur, B., Mrooz, O., Hadzaman, I., Shpotyuk, O., Aldinger, F., Seifert, H., Volkov, S., and Pekhnyo, V., Journal of Alloys and Compounds 347, 14–23, (2002).Google Scholar