Hostname: page-component-6bf8c574d5-rwnhh Total loading time: 0 Render date: 2025-02-20T14:31:45.103Z Has data issue: false hasContentIssue false
  • English
  • Français

Microstructural Design by Selective Grain Growth of β-Si3N4

Published online by Cambridge University Press:  25 February 2011

Naoto Hirosaki ,
Yoshio Akimune  and
Mamoru Mitomo
Naoto Hirosaki
Affiliation:
Nissan Motor Co., Ltd., 1, Natsushima-cho, Yokosuka, 237, Japan
Yoshio Akimune
Affiliation:
Nissan Motor Co., Ltd., 1, Natsushima-cho, Yokosuka, 237, Japan
Mamoru Mitomo
Affiliation:
National Institute for Research in Inorganic Materials, 1-1, Namiki, Tsukuba-shi, 305, Japan
Get access

Abstract

Raw β-Si3N4 powder was gas-pressure sintered with Y2 O3-Nd2O3additives at > 1700ºC. Graingrowth behavior was investigated in relation to sintering conditions. Selective growth of large grains was accomplished by sintering the powder at high temperatures with small amounts of additives. As a result, in-situ composites were obtained from β-powder.

The desired material properties have been attained by controlling the microstructural design using large grains. Materials with high reliability, having a Weibull modulus of about 50, were fabricated by maintaining a uniform size and distribution of elongated grains. Tough materials, having fracture toughness of, were developed by increasing the diameter of elongated grains. This method was applied to the sintering of refractory grade powder with the aim of lowering sintered material cost. Fairly good mechanical properties have been obtained even with impure powders.

Type
Research Article
Information
MRS Online Proceedings Library (OPL) , Volume 287: Symposium K – Silicon Nitride Ceramics–Scientific and Technological Advances , 1992 , 405
Copyright
Copyright © Materials Research Society 1993

Access options

Get access to the full version of this content by using one of the access options below. (Log in options will check for institutional or personal access. Content may require purchase if you do not have access.)

References

REFERENCES

1. Lange, F. F., J. Am. Ceram. Soc. 56, [10] 518–522, (1973).Google Scholar
2. Mitomo, M. and Mizuno, K., Yogyo-Kyokai-Shi, 94, [1] 106–11, (1986).Google Scholar
3. Tani, E., Umebayashi, S., Kishi, K., Kobayashi, K., and Nishijima, M., Am. Ceram. Soc. Bull 65, [9] 1311–15, (1986).Google Scholar
4. Li, C-W. and Yamanis, J, Ceram. Eng. Sci. Proc. 10, [7-8] 632–645 (1989).Google Scholar
5. Kawashima, T., Okaxnoto, H., Yamanmoto, H., and Kitamura, A., J. Ceram. Soc. Japan 99 [4] 320–323, (1991).Google Scholar
6. Mitomo, M., Tsutsumi, M., Tanaka, H., Uenosono, S., and Saito, F., J. Am. Ceram. Soc. 73, [8] 2441–45, (1990).Google Scholar
7. Hirosaki, N., Ando, M., Akimune, Y., and Mitomo, M., J. Ceram. Soc. Japan 100 [6] 826–829, (1992).Google Scholar
8. Mitomo, M., in Proceeding of the 1st International Symposium of the Science of Engineering Ceramics, edited by Kimura, S. and Niihara, K., (The Ceramic Society of Japan 1991), p. 101–107.Google Scholar
9. Nose, T. and Fujii, T., J. Am. Ceram. Soc., 71, [5] 328–33, (1988).Google Scholar
10. Sarian, S. and Weart, H. W., J. Appl. Phys., 37 [4] 1675–81, (1966).Google Scholar
11. Hirosaid, N. and Okada, A., J. Ceram. Soc. Jpn., 97 [6] 673–675, (1989).Google Scholar
12. Mitomo, M. and Uenosono, S., J. Am. Ceram. Soc. 75, [1] 103–108, (1992).Google Scholar
13. Rice, R. W., McKinney, K.R., Wu, C. C., Freiman, S. W. and Donough, W. J. M., J.Mater. Sci., 20 [4]1392–1406 (1985).Google Scholar
14. Okada, A. and Hirosaki, N., J. Mater. Sci., 25 1656–61 (1990).Google Scholar
15. Rice, R. W., Freiman, S. W., and Becher, P. F., J. Am. Ceram. Soc. 64 [6] 345–350, (1981).Google Scholar