Hostname: page-component-586b7cd67f-tf8b9 Total loading time: 0 Render date: 2024-11-25T17:27:40.709Z Has data issue: false hasContentIssue false
  • English
  • Français

Mechanical and Tribological Properties of Chromium-Nitrogen Films Deposited by Ion Beam Assisted Deposition

Published online by Cambridge University Press:  03 September 2012

E. J. Tobin ,
F. Namavar ,
H. F. Karimy ,
C. Colerico-Stenstrom ,
R. J. Bricault ,
Justus Haupt ,
J.-P. Hirvonen  and
R. Ayer
E. J. Tobin
Affiliation:
Spire Corporation, One Patriots Park, Bedford, MA 01730–2396
F. Namavar
Affiliation:
Spire Corporation, One Patriots Park, Bedford, MA 01730–2396
H. F. Karimy
Affiliation:
Spire Corporation, One Patriots Park, Bedford, MA 01730–2396
C. Colerico-Stenstrom
Affiliation:
Spire Corporation, One Patriots Park, Bedford, MA 01730–2396
R. J. Bricault
Affiliation:
Spire Corporation, One Patriots Park, Bedford, MA 01730–2396
Justus Haupt
Affiliation:
Institute for Advanced Materials, Ispra (VA), ITALY
J.-P. Hirvonen
Affiliation:
Commrission of the European Communities, Joint Research Centre, Petten, The Netherlands
R. Ayer
Affiliation:
STEM, Inc., Woodbridge, CT.
Get access

Abstract

Mechanical and tribological properties of chromium-nitrogen films deposited by ion beam assisted deposition (IBAD) were investigated. The films were deposited reactively, i.e., via chromium evaporation with concurrent nitrogen ion beam bombardment, on stainless steel substrates at low deposition temperatures (<200°C). Two primary deposition regimes, with differing Cr/N atom-to-ion arrival ratios, were investigated: approximately 0.8–1.0 and 2.5–3.0. Rutherford Backscattering Spectroscopic analysis showed the lower arrival ratio films to be essentially stoichiometric CrN, whereas films deposited at higher arrival ratios were Cr-rich with Cr/N ratios of about 3:1. Both films were fine grained polycrystalline (typically 5–20 nanometer crystal dimension). The stoichiometric films were approximately two times harder than the Cr-rich films., based on nanohardness indentation measurements, and possessed higher residual stress levels. Both film types substantially improved the wear resistance of stainless steel disks, based on the results of ball-ondisk wear tests against ruby balls. The best performance was obtained with Cr-rich films, which exhibited a very low wear rate and lower friction than either the stoichiometric film or the uncoated steel.

Type
Research Article
Information
MRS Online Proceedings Library (OPL) , Volume 438: Symposium A – Materials Modificaton and Synthesis by Ion Beam… , 1996 , 657
Copyright
Copyright © Materials Research Society 1997

Access options

Get access to the full version of this content by using one of the access options below. (Log in options will check for institutional or personal access. Content may require purchase if you do not have access.)

References

1. Ramalingam, S., Wear, 118, 335 (1984).Google Scholar
2. Zlatanovic, M. and Munz, W.D., Surf. Coat. Technol., 41, 17–32 (1990).Google Scholar
3. Munz, W.D., J. Vac. Sci. Technol., A 4, 2717 (1986).Google Scholar
4. Freller, H. and Haessler, H., Thin Solid Films, 153, 433 (1987).Google Scholar
5. Navinsek, B. and Panjan, P., Thin Solid Films, 223, 4 (1993).Google Scholar
6. Ichimura, H. and Kawana, A., J. Mater. Res., 9(1), 151–155 (1994).Google Scholar
7. Chiba, Y., Omura, T., and Ichimura, H., J. Mater. Res., 8(5), 1109–1115 (1993).Google Scholar
8. Kacsich, T., Neubauer, M., Geyer, U., Baumann, K., Rose, F., and Uhmacher, M., J. Phys. D: Appl. Phys., 28, 424–431 (1995).Google Scholar
9. Sugiyama, H.K., Hayashi, K., Sasaki, J., Ichiko, O., and Hashiguchi, Y., Nuclear Instruments and Methods in Physics Research, B80/81, 1376–1379 (1993).Google Scholar