Hostname: page-component-78c5997874-94fs2 Total loading time: 0 Render date: 2024-11-08T04:45:00.626Z Has data issue: false hasContentIssue false
  • English
  • Français

Magnetron Sputtered Ti-Basis Hard Material Coatings on Thermoplastic Polymers for Applications in Particle Sensitive Environments

Published online by Cambridge University Press:  10 February 2011

E. Lugscheider ,
S. Barwulf ,
C. Barimani ,
M. Riester  and
H. Hilgers
E. Lugscheider
Affiliation:
Materials Science Institute, University of Technology Aachen, Augustinerbach 4-22, 52056 Aachen, Germany
S. Barwulf
Affiliation:
Materials Science Institute, University of Technology Aachen, Augustinerbach 4-22, 52056 Aachen, Germany
C. Barimani
Affiliation:
Materials Science Institute, University of Technology Aachen, Augustinerbach 4-22, 52056 Aachen, Germany
M. Riester
Affiliation:
IBM Storage Systems Germany GmbH, Hechtsheimer StraBe 2, 55131 Mainz, Germany
H. Hilgers
Affiliation:
IBM Storage Systems Germany GmbH, Hechtsheimer StraBe 2, 55131 Mainz, Germany
Get access

Abstract

Even under demanding environments, like clean rooms, polymers are already used in different-ranges of applications. The wear and particle generation within a specific particle size even under-mechanical stress is a limiting factor. So it was the aim to develop an innovative material-concept, that enables to apply a thermoplastic polymer coated with a thin hard material (thickness-up to 2.5 gm), which also prevents for electrostatical discharges and is usable for complex-bodies. Therefore it was necessary to improve the wear resistance and the adherence between the-polymer and the coating. To take also economic aspects into consideration a two step production-process sequence was required, consisting of the injection moulding process and then the plasma-deposition process including a plasma pre-treatment. In this investigation, poly(butyleneterephthalate)-(PBT) and poly(amide) 6.6 (PA) and polycarbonate (PC) were chosen as substrate-material. The coating materials used, which were mainly deposited by Magnetron Sputter Ion-Plating (MSIP), were on titanium basis (Ti-N). To get detailed chemical information about the-coatings and the interfacial region they were analyzed by X-Ray Photoelectron Spectroscopy-(XPS), additionally Secondary Ion Mass Spectrometry (SIMS) experiments were carried out to-confirm the results. The process parameter's influence on the microstructure, which extend from-amorphous to columnar (crystalline), and the film thickness were analyzed by SEM. It will be-shown and discussed, that it is possible to improve the coating's adherence by plasmapretreatment-as well as to reduce the particle generation after a suitable etching and coating process.

Type
Research Article
Information
MRS Online Proceedings Library (OPL) , Volume 544: Symposium Y – Plasma Deposition and Treatment of Polymers , 1998 , 191
Copyright
Copyright © Materials Research Society 1999

Access options

Get access to the full version of this content by using one of the access options below. (Log in options will check for institutional or personal access. Content may require purchase if you do not have access.)

References

[1] Federal, N.N. Standard 209;Google Scholar
[2] VDI-Richtlinie, N.N. 2083 Google Scholar
[3] Gath, H.-C. and Simon, R., Reinraumtechnik: Entwicklung, Stand, Perspektiven, Handbuch der Reinraumpraxis, Ecomed Verlag, (1991)Google Scholar
[4] Wan, C.T., Chambers, D.L., Susi, G. T. and Taylor, K.A., in Metallized Plastics, edited by Mittal, K.L., Vol. 2, Plenum Press, New York, (1991) 81–95 Google Scholar
[5] Nowak, S., Mauron, R., et al., in Metallized Plastics, edited by Mittal, K.L.,, Vol.2, Plenum Press, New York,(1991) 233–244 Google Scholar
[6] Van Stappen, M., Malliet, B., et. al., Surf. Eng. 5 (4) (1989) 305–310 Google Scholar
[7] Holleck, H., Surf. Eng. 7 (2) (1991) 137 - 144Google Scholar
[8] Vallon, S., Hofrichter, A., et al., Thin Solid Films. 290–291 (1996) 68–73.Google Scholar
[9] Nakumara, Y., Suzuki, Y., Watanabe, Y., Thin Solid Films. 290–291 (1996) 367–369 Google Scholar
[10] Meyer, M., Suchentrunk, R., et al., Surf. Coat. Technol. 59 (1993) 297–300 Google Scholar
[11] Friedrich, J. F., Rohrer, P., Saur, W., et al., Surf. Coat. Technol. 59 (1993) 371–378 Google Scholar
[12] Harth, K., Hibst, H., Surf. Coat. Technol. 59 (1993) 350–355 Google Scholar
[13] Mann, D. A., Leyendecker, F., Surf. Coat. Technol. 68/69 (1994) 691–695 Google Scholar
[14] Riester, M., Titannitrid auf Thermoplasten - Untersuchung zu vier Werkstoffverbunden, doctorate thesis, Univ. OsnabrÜck, Shaker 1998 Google Scholar
[15] Hilgers, H., Riester, M., et al., Anforderungen und Charakterisierungb eschichteter Polymereffir Reinraumanwendungen, paper printed in proceedings: Verbundwerkstoffe und Werkstoffverbunde”, DGM 17.9.97-19.9.97, Kaiserslautern, GermanyGoogle Scholar
[16] Lugscheider, E., Bärwulf, S., et al., Magnetron Sputtered Hard Material Coatings On Thermoplastic Polymers For Clean Room Applications, reviewed and accepted paper, will be published in proceedings ICMCTF 98, San Diego and Surf. Coat. Tech.Google Scholar
[17] Riester, M., Lutz, A., Hilgers, H. and Friedrich, K., Surf. Coat. Technol. 97 (1997) 649–655 Google Scholar
[18] Lugscheider, E., Bdrwulf, S., et al., Magnetron Sputtered Titanium Nitride Thin Films On Thermoplastic Polymers, submitted paper for publication, will be published in proceedings PSE ‘98, Garmisch Partenkirchen, GermanyGoogle Scholar