Hostname: page-component-586b7cd67f-dlnhk Total loading time: 0 Render date: 2024-11-23T12:21:46.670Z Has data issue: false hasContentIssue false
  • English
  • Français

Magnetron Sputtered Intermetallic Al2Au and Al-Zr-Y Coatings for the Oxidation Protection of γ-TiAl

Published online by Cambridge University Press:  26 February 2011

Martin Moser ,
Paul Heinz Mayrhofer  and
Reinhold Braun
Martin Moser
Affiliation:
[email protected], University of Leoben, Physical Metallurgy and Materials Testing, Franz-Josef Str. 18, Leoben, 8700, Austria, +43/3842/402/4229, +43/3842/402/4202
Paul Heinz Mayrhofer
Affiliation:
[email protected], University of Leoben, Department Physical Metallurgy and Materials Testing, Franz-Josef-Str.18, Leoben, A-8700, Austria
Reinhold Braun
Affiliation:
[email protected], DLR - German Aerospace Centre, Institute of Materials Research, Cologne, D-51170, Germany
Get access

Abstract

Al-based intermetallic coatings are widely used as bond coats and for oxidation protection of turbine blades and engine components. Here we present and discuss the structural and thermal properties of novel unbalanced-magnetron sputtered Al-based coatings (single-phase intermetallic Al2Au, binary Al-Zr, and nano-structured Al-Zr-Y) developed to protect gamma-TiAl from environmental attack at elevated temperatures. Al-Zr films exhibit a coarse-grained dual-phase Al3Zr2-Al2Zr structure and are nano-structured by alloying with ~5, 10, and 14 at% Y.

Combined dynamic differential-scanning calorimetry and thermogravimetric analyses up to a temperature of 1150 °C reveal that the Al2Au film is very stable with only marginal mass gain from oxidation found between 800 and 1000 °C. High temperature X-ray diffraction shows that this coating retains its (311) texture up to 900 °C where Al2O3 formation leads to the depletion of Al in Al2Au and subsequently the precipitation of intermetallic AlAu. When gamma-TiAl is coated with Al2Au and exposed to cyclic oxidation tests at 750 and 850 °C good oxidation resistance is obtained as a protective oxide layer is formed.

Dual-phase Al3Zr2-Al2Zr coatings form ZrO2 and Al2O3 in oxidizing atmosphere. However, the phase transition from monoclinic (m-)ZrO2 to tetragonal (t-)ZrO2 with the accompanying volume change causes flaking of the oxide. Yttrium addition to the Al-Zr films stabilizes the cubic (c-) and t-ZrO2 and hence avoids the fatal tetragonal-monocline transformation. The thermally grown c-ZrO2 based oxides allow good adhesion to thermal barrier coatings which are themselves based on c-ZrO2.

Keywords

oxidationphysical vapor deposition (PVD)coating
Type
Research Article
Information
MRS Online Proceedings Library (OPL) , Volume 980: Symposium II – Advanced Intermetallic-Based Alloys , 2006 , 0980-II05-08
Copyright
Copyright © Materials Research Society 2007

Access options

Get access to the full version of this content by using one of the access options below. (Log in options will check for institutional or personal access. Content may require purchase if you do not have access.)

References

REFERENCES

1. Clemens, H., Lorich, A., Eberhardt, N., Glatz, W., Knabl, W., and Kestle, H., Z Metallkd 90 (8), 569–580 (1999).Google Scholar
2. Clemens, H. and Kestler, H., Adv. Eng. Mater. 2, 551 (2000).Google Scholar
3. Kestler, H. and Clemens, H., in Titanium and Titanium Alloys, edited by Leyens, C. and Peters, M. (Wiley-VCH, 2003) pp. 351–392.Google Scholar
4. Appel, F. and Wagner, R., Materials Science and Engineering: R: Reports 22, 187 (1998).Google Scholar
5. Leyens, C., Peter, M., Hovsepian, P. Eh., Lewis, D. B., Luo, Q., and Münz, W-D., Surf. Coat. Technol. 155, 103–111 (2002).Google Scholar
6. Schütze, M. ed., Corrosion and Environmental Degradation Vol. II, (Wiley-VCH, London)Google Scholar
7. Pichoir, R., Aluminide coatings on nickel or cobalt-base superalloys, in High Temperature Alloys for Gas Turbines, edited by Coutsouradis, D. et al., (Appl. Sci. Pub., London, 1978), p. 191.Google Scholar
8. Zhang, Y., Aluminide coatings for power-generation applications, Technical Report, ORNL/Sub/01-47035/01Google Scholar
9. Sivakumar, R. et al., Surf. Sci. Techn., 37, 139 (1989)Google Scholar
10. Moser, M., Mayrhofer, P. H., Ross, I. M., and Rainforth, W. M.: Thermal Stability of Sputtered Intermetallic Al-Au Coatings, submitted, 2006.Google Scholar
11. Mitterer, C., Lenhart, H., Mayrhofer, P. H., and Kathrein, M., Intermetallics 12, 579 (2004)Google Scholar
12. Murray, J., Peruzzi, A., and Abriata, J. P., J. Phase Equilibria, 13, 277–291 (1992)Google Scholar
13. Yashima, M., Kakihana, M., and Yoshimura, M., Solid State Ionics, 86–88, 1131 (1996),Google Scholar
14. Stecura, S., NASA Tech. Memo. (1985), 86905Google Scholar
15. Moser, M., Mayrhofer, P. H., Ross, I. M., and Rainforth, W. M.: Microstructure and Mechanical Properties of Sputtered Intermetallic Al-Au Coatings, submitted, 2006 Google Scholar
16. Okamoto, H., J. Phase Equilibria, 12, 114–115 (1991)Google Scholar
17. Trethewey, K. R. and Chamberlain, J., in Corrosion for Science and Engineering, 2nd Edition, (Longman Group Ltd., Singapore, 1995)Google Scholar
18. Ross, I.M., Walker, J.C., Moser, M., Mayrhofer, P.H., Braun, R., and Rainforth, W.M., Structural Characterization of Al-Au Based Intermetallic Coatings Prepared by Unbalanced Magnetron Sputtering, in preparation for ICMCTF 2007, San Diego, US Google Scholar
19. Lakiza, S., Fabrichnaya, O., Zinkevich, M., Aldinger, F., J. Alloys and Comp., 420, 237 (2006)Google Scholar