Hostname: page-component-586b7cd67f-l7hp2 Total loading time: 0 Render date: 2024-11-26T01:34:51.164Z Has data issue: false hasContentIssue false
  • English
  • Français

The High Temperature Deformation Behavior of A Cr2Nb Ordered Intermetallic System

Published online by Cambridge University Press:  26 February 2011

G. E. Vignoul ,
J.M. Sanchez  and
J. K. Tien
G. E. Vignoul
Affiliation:
Strategic Materials R&D Laboratory, The University of Texas, Austin, Texas 78721
J.M. Sanchez
Affiliation:
Strategic Materials R&D Laboratory, The University of Texas, Austin, Texas 78721
J. K. Tien
Affiliation:
Strategic Materials R&D Laboratory, The University of Texas, Austin, Texas 78721
Get access

Abstract

A basic characterization of the deformation behavior of Cr2Nb by microindention at ambient and elevated temperatures (up to 1400 °C) was undertaken. The microhardness of this system was seen to decrease with increasing temperature, from 1040 MPa at 25°C to 322 MPa at 1400 °C. Further, the microindention creep behavior of this system was studied by varying time on load at T = 1000 and 1200°C. Analysis of the data showed that m = 24 and Qapp = 477.61 kJ/mole. These unusually high values are indicative of the existence of an effective resisting stress against creep. When the data was fit against a microindention creep deformation law which was modified to incorporate an effective resisting stress term, it was determined that m = 4.5, Qcreep = 357 kJ/mole and the resisting stress term σr = 300 MPa.

Type
Research Article
Information
MRS Online Proceedings Library (OPL) , Volume 213: Symposium Q – High-Temperature Ordered Intermetallic Alloys IV , 1990 , 739
Copyright
Copyright © Materials Research Society 1991

Access options

Get access to the full version of this content by using one of the access options below. (Log in options will check for institutional or personal access. Content may require purchase if you do not have access.)

References

REFERENCES

1. In Binary Alloy Phase Diagrams, vol. 1, editted by Massalski, T.B., Murray, J.L., Bennett, L.H. and Baker, H. (American Society for Metals, Metals Park, OH 1986), p. 839 Google Scholar
2. Kear, B.H. and Wisldorf, H.G.F., Trans. AIME 224, 382 (1962)Google Scholar
3. Takeuchi, S. and Kuramoto, E., Acta Metall. 21,415 (1973)CrossRefGoogle Scholar
4. Paider, V., Pope, D.P. and Vitek, V., Acta Metall. 32, 435 (1984)CrossRefGoogle Scholar
5. Atkins, A.G., Siverio, A. and Tabor, D., J. of the Institute of Metals 94, 369 (1966)Google Scholar
6. Atkins, A.G., Siverio, A. and Tabor, D., J. of the Institute of Metals 94, 369 (1966)Google Scholar
7. Howson, T.E., Stulga, J.E. and Tien, J.K., Met. Trans. 11A, 1599 (1980)CrossRefGoogle Scholar
8. Livingston, J.D., Hall, E.L. and Koch, E.F. in High Temperature Ordered Intermetallic Alloys III, edited by Liu, C.T., Taub, A.I., Stoloff, N.S. and Koch, C.C. (Mater. Res. Soc. Proc. 133, Pittsburgh, PA 1989), pp. 243–248 Google Scholar